Table of Contents
Advertisement
Quick Links
Connecting Cisco Analog Video Gateway
Network Modules to the Network
Revised: May 1, 2008, OL-16670-01
This guide describes how to connect Cisco Analog Video Gateway network modules to your network. It
contains the following sections:
•
•
•
•
Information About the EVM-IPVS-16A Network Module
The EVM-IPVS-16A network module enables Cisco integrated services routers to capture analog video
signals. The EVM-IPVS-16A network module supports up to 16 simultaneous composite video inputs,
such as video surveillance cameras. The EVM-IPVS-16A network module also provides alarm input
detection, control relay outputs, and RS-485 serial communication interfaces.
EVM-IPVS-16A network module faceplate.
You need a router that supports the EVM-IPVS-16A network module. For a list of supported platforms,
Note
see the Cisco Analog Video Gateway Network Module (EVM-IPVS-16A) Data Sheet.
Americas Headquarters:
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Information About the EVM-IPVS-16A Network Module, page 1
How to Install, Connect, or Replace the EVM-IPVS-16A Network Module, page 5
Related Documents, page 12
Obtaining Documentation, Obtaining Support, and Security Guidelines, page 13
Figure 1
shows the
Advertisement
Table of Contents
Related Manuals for Cisco EVM-IPVS-16A
Summary of Contents for Cisco EVM-IPVS-16A
- Page 1 RS-485 serial communication interfaces. Figure 1 shows the EVM-IPVS-16A network module faceplate. You need a router that supports the EVM-IPVS-16A network module. For a list of supported platforms, Note see the Cisco Analog Video Gateway Network Module (EVM-IPVS-16A) Data Sheet. Americas Headquarters:...
-
Page 2: Video Ports
Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Warning Statement 1030 The compact flash module installed in the EVM-IPVS-16A network module is not field-replaceable. Note For software-related prerequisites and restrictions, see the Cisco Analog Video Gateway 1.0 Installation... -
Page 3: Rs-485 Serial Communication Interfaces
The EIA/TIA RS-485 communications standard supports up to 32 devices (driver/receiver pairs) on a cable of up to 4,000 feet. The EVM-IPVS-16A network module has two RS-485 ports, supporting up to 64 devices. The EVM-IPVS-16A network module typically acts as the master for each of the two RS-485 networks. -
Page 4: Evm-Ipvs-16A Network Module Connectors
Video (labeled VIDEO) DB-37 female connector DB-37 to BNC video breakout cable (provided) EVM-IPVS-16A Network Module LEDs The Cisco analog video gateway network module (EVM-IPVS-16A) has LEDs which denote the status of the network module, shown in Figure 3 and described in... -
Page 5: How To Install, Connect, Or Replace The Evm-Ipvs-16A Network Module
This section contains the following procedures, each of which may or may not be required, depending on which tasks your service provider performs for you: Installing the EVM-IPVS-16A Network Module in the Router Chassis, page 6 • Connecting the EVM-IPVS-16A Network Module to the Network, page 8 •... -
Page 6: Installing The Evm-Ipvs-16A Network Module In The Router Chassis
Performing Online Insertion and Removal of the EVM-IPVS-16A Network Module, page 10 • Installing the EVM-IPVS-16A Network Module in the Router Chassis To install the EVM-IPVS-16A network module in the router chassis, see the Installing Cisco Network Modules in Cisco Access Routers guide at: http://www.cisco.com/en/US/docs/routers/access/interfaces/nm/hardware/installation/guide/InstNetM. - Page 7 Connecting Cisco Analog Video Gateway Network Modules to the Network How to Install, Connect, or Replace the EVM-IPVS-16A Network Module Table 4 a plus (+) sign and minus (–) sign are used to note the polarity for the contact closure and Note RS-485 ports.
-
Page 8: Connecting The Evm-Ipvs-16A Network Module To The Network
Connecting Cisco Analog Video Gateway Network Modules to the Network How to Install, Connect, or Replace the EVM-IPVS-16A Network Module Connecting the EVM-IPVS-16A Network Module to the Network This section describes how to connect the EVM-IPVS-16A network module to devices in the video surveillance network. Note If an installation technician has already connected the EVM-IPVS-16A to the devices in your network, then do not perform this task. - Page 9 After you have wired the provided terminal block connectors according to the pinout information provided in Table 4, connect the terminal block connectors to the terminal block on the EVM-IPVS-16A network module and tighten the screws using a small slotted screwdriver. Figure 6...
-
Page 10: What To Do Next
Also, routing information is maintained during OIR of network modules. If your router does not support OIR, do not perform this task to replace your EVM-IPVS-16A network Note module. - Page 11 Hazardous voltages may be present in the outdoor camera cables under fault conditions. Disconnect Warning all cables from the outdoor cameras before servicing this equipment. Statement 376 Disconnect the DB-37 to BNC video breakout cable from the VIDEO connector on the EVM-IPVS-16A Step 4 network module.
-
Page 12: Related Documents
Connecting Cisco Analog Video Gateway Network Modules to the Network Related Documents Connect the terminal block connector cables to the terminal blocks on the EVM-IPVS-16A network Step 11 module. Step 12 Confirm that the network module LEDs come on. For more information about the LEDs, see the “EVM-IPVS-16A Network Module LEDs”... -
Page 13: Obtaining Documentation, Obtaining Support, And Security Guidelines
CCDE, CCENT, Cisco Eos, Cisco Lumin, Cisco Nexus, Cisco StadiumVision, the Cisco logo, DCE, and Welcome to the Human Network are trademarks; Changing the Way We Work, Live, Play, and Learn is a service mark; and Access Registrar, Aironet, AsyncOS, Bringing the Meeting To... - Page 14 Connecting Cisco Analog Video Gateway Network Modules to the Network Obtaining Documentation, Obtaining Support, and Security Guidelines Connecting Cisco Analog Video Gateway Network Modules to the Network...