Watchguard Firebox M200 Configuration Manual
  1. Manuals
  2. Brands
  3. Watchguard Manuals
  4. Network Router
  5. Firebox M200
  6. Configuration manual

Watchguard Firebox M200 Configuration Manual

Firewall/router
Hide thumbs Also See for Firebox M200:
Table of Contents

Advertisement

Quick Links

WatchGuard M200 Firewall/Router
QoS Configuration Guide

Advertisement

Table of Contents
loading

Related Manuals for Watchguard Firebox M200

Summary of Contents for Watchguard Firebox M200

  • Page 1 WatchGuard M200 Firewall/Router QoS Configuration Guide...

  • Page 2: Table Of Contents

    Configure Your Fir ewall ....... . . 4 WatchGuard M200 Firewall Configuration .

  • Page 3: Introduction

     less fierce than those targeting larger organizations.. IPS — 1.4 Gbps  The Firebox M200 Unified Threat Management (UTM) solution is up to UTM — 515 Mbps  3 times faster than competing products with all security layers turned 1 Gig ports —...

  • Page 4: Configure Your Firewall

    To review the Quick Start Guide for the WatchGuard M200 click here. See the WatchGuard M200 Hardware Guide here. Log into your WatchGuard. For information about logging into your WatchGuard GUI for first time setup, please refer to the WatchGuard Quick Start Guide.
  • Page 5 QoS Configuration Guide | WatchGuard M200 | Configure Your Firewall Navigate to ‘Firewall’ and select subcategory ‘Firewall Policies’. Hit the ‘Add Policy’ button.. (Figure 2) Figure 2...
  • Page 6 QoS Configuration Guide | WatchGuard M200 | Configure Your Firewall In Figure 2 above, under ‘Select Policy Type’ hit ‘Custom’. Then hit ‘Add’. Name your new policy “RingCentral”. Keep ‘Type’ as Packet Filter. Under Protocols, enter all applicable RingCentral ports.
  • Page 7 QoS Configuration Guide | WatchGuard M200 | Configure Your Firewall Now we need to finalize the configuration of the RingCentral Policy. Under the ‘Settings’ tab: (Figure 4) In the ‘From’ table, change it from ‘Any-trusted’ to ‘Any’, change if you have VLANs setup and want to specific ‘From’ endpoints.
  • Page 8 QoS Configuration Guide | WatchGuard M200 | Configure Your Firewall Now navigate to the ‘Traffic Management’ tab. (Figure 5) Under ‘Forward Action (From > To)’, hit ‘Add’. To help calculate these values, check here on Section 10. Name is ‘RC BWM’...
  • Page 9 QoS Configuration Guide | WatchGuard M200 | Configure Your Firewall Now navigate to the ‘Advanced’ tab. (Figure 6) Browse down to the ‘QoS’ section and modify the following values : Change ‘Marking Type’ to ‘DSCP’ Change ‘Marking Method’ to ‘Assign’...

  • Page 10: Quality Of Service

    RingCentral cannot control the final configuration of highest-possible QoS experience on the WatchGuard M200 the hardware or your computer systems/networks, or promise Firewall/Router. Please reference the relevant TCP/UDP settings on the that any given router will work with your system, or guarantee that our information is 100% up to date.

  • Page 11: Test Your Connection Quality

    QoS Configuration Guide | WatchGuard M200 | Quality of Service Test Your Connection Quality RingCentral provides a VoIP Quality test that will simulate VoIP calls between your computer and RingCentral, and provide an estimate of the voice quality you should expect when using our service. For the...

  • Page 12: Ports And Firewalls Settings For Ringcentral Voip Service

    QoS Configuration Guide | WatchGuard M200 | Ports and Firewalls Settings for RingCentral VoIP Service Ports and Firewalls Settings for RingCentral VoIP Service Please see RingCentral Ports and Firewalls reference link for the required TCP/UDP ports that need to be opened for RingCentral devices to work.

Table of Contents