Advertisement
LOCATION OF CONTROLS
1.
Speakers
2.
Power/Alarm Off Button
3.
Play/Pause/Sync Button
4.
Function/Clock Adj. Button
5.
Skip-/Tune- Button
6.
Skip+/Tune+ Button
7.
Memory-/Alarm 1 Button
8.
Memory+/Alarm 2 Button
9.
P-Mode Button
10.
Sleep Button
11.
Snooze Button
12.
Stop Button
13.
Program/Mem Button
14.
Volume– Button
15.
Volume+ Button
16.
CD Door Open Button
17.
CD Door
18.
Display
19.
Remote Sensor
20.
Adjustable Dock Dial
21.
iPod/iPhone Connector
22.
FM Wire Antenna
23.
Aux-In Jack
24.
DC In Jack
25.
Remote Control
- 4 -
CONNECTING THE UNIT TO POWER
Plug one end of the AC/DC adaptor into the DC-In jack, and then plug the other end into AC wall outlet.
Before switching on the unit, make sure that the voltage of your electricity supply is the same as that
indicated on the rating plate.
CONNECTING THE LOUDSPEAKERS
Connect the cables of the two loudspeakers to the corresponding input (R) for the right speaker and
input (L) for the left speaker, located at the side of the unit.
Warning: Connect the loudspeakers before powering the unit. The unit may not work properly or get
damaged if you use speakers different than the ones supplied with the unit.
SETTING THE TIME
Before starting to set the time, make sure that the unit is in POWER OFF Mode.
If you have iPod (Except iPod Shuffle) or iPhone
1.
Dock in the iPod/iPhone on the 30 pins Connector
2.
Press the 'PLAY/PAUSE/SYNC' button for a few seconds until the display will show SYNC with
flashing, then the unit will synchronize the time same as the iPod/iPhone's automatically.
If you do not have any iPod/iPhone units
1.
Press and hold the 'FUNC/CL ADJ' button for a few seconds, the hour digit in the display will start
flashing.
2.
Press the 'SKIP+/TUNE+' or 'SKIP-/TUNE-' button to adjust the hour.
3.
When the correct hour is selected, press the 'FUNC/CL.ADJ' button again, the minute digit in the
display will start flashing.
4.
Press the 'SKIP+/TUNE+' or 'SKIP-/TUNE-' button to adjust the minute.
5.
When the correct time is selected, press the 'FUNC/CL ADJ' button to store the time in the memory.
SETTING THE ALARM TIME
Before starting to set the alarm time, make sure that the unit is in POWER OFF mode.
1.
Press the 'MEM-/AL1' or 'MEM+/AL2' button on the unit once (you can also use the 'AL1' or 'AL2'
button on the remote control) and the AL1 or AL2 icon will appear in the display.
2.
Press the 'FUNC/CL. ADJ.' button to select the alarm wake up source. The options are buzzer,
iPod/iPhone, Radio or CD.
3.
Press and hold the 'MEM-/AL1' or 'MEM+/AL2' button on the unit for a few seconds (you can also
use the 'AL1' or 'AL2' button on the remote control), the alarm hour digit will begin flashing.
4.
Press the 'SKIP+/TUNE+' or 'SKIP-/TUNE-' button on the unit to adjust the alarm hour.
5.
When the desired alarm hour is selected, press the 'MEM-/AL1' or 'MEM+/AL2' button again, (you
can also use the 'AL1' or 'AL2' button on the remote control), the alarm minute digit will begin
flashing.
6.
Press the 'SKIP+/TUNE+' or 'SKIP-/TUNE-' button on the unit to adjust the alarm minute.
7.
When the desired alarm time is selected, press the 'MEM-/AL1' or 'MEM+/AL2' button again to
confirm. (You can also use the 'AL1' or 'AL2' button on the remote control).
Note : If you choose iPod/iPhone or CD as the alarm wake up source, please make sure that you have
the iPod/iPhone or CD in place.
- 5 -
Advertisement
