Page 3
English Contents Dear Customer, KombiSystem Guide to Using this Manual Thank you for choosing a quality engineered STIHL product. Safety Precautions and Working Techniques It has been built using modern Using the Unit production techniques and comprehensive quality assurance. Approved KombiEngines...
Caution where there is a risk of serious or even fatal damaging the machine or its individual In the STIHL KombiSystem a number of injury. components. different KombiEngines and KombiTools Lend or rent your power tool only to...
Page 5
STIHL recommends the use of genuine STIHL tools and accessories. They are specifically designed to match the product and meet your performance WARNING requirements.
Page 6
To reduce the risk of burn Make sure you always have good injury, do not touch the 15m (50ft) balance and secure footing. gearbox housing. Always hold the power tool firmly with both hands on the handles. FCB-KM...
Page 7
Shut off the engine. exhaustion. for cracks. After finishing work, clean dirt, soil and Replace a damaged blade – plant residue off the cutting attachment – immediately, even if it has only wear gloves to reduce the risk of injury. superficial cracks. FCB-KM...
Only use deflectors or attachments servicing dealer. which have been approved by STIHL for STIHL recommends the use of genuine this machine or which are technically Preparations STIHL replacement parts. They are equivalent.
Page 9
The deflector has been set by the manufacturer so that the arrow on the deflector and the open side point away from the operator. This ensures that cuttings and other debris will be directed away from the machine and operator. FCB-KM...
This KombiTool may be operated only in combination with the following KombiEngines: STIHL KM 55 R, KM 56 R, KM 85 R, KM 90, KM 90 R, KM 94 R, KM 100, KM 100 R, KM 110, KM 110 R, KM 130,...
Reverse the above sequence to Push the shaft (3) in as far as it will remove the drive tube. Screw in the clamping screw (1) as far as it will go – do not tighten yet! FCB-KM...
(4) until the shaft is blocked. becomes fatigued, then the nut must be the control handle while doing so – replaced! Fit Allen wrench (5) onto nut (6). see instruction manual for the KombiEngine or basic power tool FCB-KM...
Remove, clean and inspect the that maintenance and repair work be cutting blade. If the engine is started, the blade may carried out only by authorized STIHL If the KombiTool is removed from rotate as soon as the engine is running – dealers.
Do not attempt to straighten or weld a bent or cracked blade – it may break – it must be replaced – see "Mounting the Cutting Blade". STIHL recommends you use only the following original STIHL cutting blades: Length Thick-...
Check that it is secure, before starting work If necessary, have it checked to see if it is out of balance, replace if it is out of balance – see "Replacing the blade" Replace if damaged – see "Replacing the blade" FCB-KM...
English Protection against wear servicing dealer. STIHL dealers are Minimize Wear and Avoid regularly given the opportunity to attend Check before starting work Damage training courses and are supplied with Replace if necessary – see "Check the necessary technical information.
Sound power level L to ISO 11789 Noise and vibration data measurements the sound pressure level and sound on power tools with the FCB-KM KM 94 R with loop handle: 103 dB(A) power level; the K-factor in accordance KombiTool include idling and rated with Directive 2006/42/EC is 2.0 m/s...
When repairing the machine, only use the garbage can. Take the product, replacement parts which have been accessories and packaging to an approved by STIHL for this power tool or approved disposal site for environment- are technically identical. Only use high- friendly recycling.
English Done at Waiblingen, 28.10.2016 EC Declaration of Conformity ANDREAS STIHL AG & Co. KG p p. ANDREAS STIHL AG & Co. KG Badstr. 115 D-71336 Waiblingen Germany declare in exclusive responsibility that the product Thomas Elsner Director Product Management and...