Caller Id - Coby CD-RA195 Operating Manual

5. Press to exit the Caller ID log.
To Delete All Records
1. Press .
2. Press and hold . The display will show
3. To delete all the Caller ID records press
Returning Caller ID Calls
You can return calls by using the Caller ID callback feature.
1. Press .
2. Use the to scroll to the call record you wish to call back.
3. If the number displayed is not correct (needing 7, 10,11 digits), use the
number to display the correct number of digits to be dialed.
Press
4. Press to dial out the displayed number.
5. Press to cancel dialing.
6. To end the call, press or place the handset back in the base.
MESSAGE WAITING AND OTHER FEATURES
If you subscribe to voice mail from the telephone company and if there are voice messages that
have been left in your voice mailbox, the display will show
Note: This function requires voice mail subscription from the local telephone company.
Furthermore, the local phone company must provide a type of voice mail signaling called FSK
(Frequency Shift Key) Not all telephone companies have the visual message waiting feature
available. Please contact your local telephone company to check if this is available in your area.
Tip: If you wish to delete the "Message Waiting" message, delete it as described in the handset
settings section Deleting the Message Waiting Indication (see page 12-13).
New Call Light : When you receive a Caller ID message, voice mail message, or when the
phone is ringing, the New Call light will flash accordingly.
!
For Caller ID, the New Call light will flash to indicate that you have a new Caller ID call stored in
memory.
!
When you have a voice message waiting the New Call light will also flash.
Using the Handset Finder (PAGE)
1. Press on the base.

CALLER ID

"ERASE ALL?"
.
key to toggle the
Press
" MSG WAITING " (see note below).
If the handset is within range,it
will beep for 20 seconds.
25
2. Place the handset back into the base or press the
feature.
Out-of-Range Warning:
display will show " OUT RANGE"
or the call will be dropped. When the base detects that the handset has been out of range for 20
continuous seconds it will release the engaged line. If you try to access the line when the handset
is out of range of the base, the display will show
Channel Changing: If you are experiencing interference during a telephone call, press
key. The CD-RA195 will scan up to 40 channels and select the clearest one to provide the best
possible reception. If the current channel is the clearest available channel, it will keep you on that
channel.
CARE MAINTENANCE AND TROUBLESHOOTING
Your CD-RA195 telephone has been designed to give 90 days of trouble-free service.It is a
sensitive electronic instrument. To assure its longevity, please read the following maintenance
instructions.
1. Keep the CD-RA195 away from heat as high temperatures can shorten the life of the electrical
components and distort or melt its plastic parts.
2. The CD-RA195 should be kept free of dust and moisture. If it gets wet, wipe it dry immediately.
Liquids can contain minerals that can corrode electronic circuits.
3. Handle your CD-RA195 gently and carefully. Dropping it can cause serious damage to circuitry,
or the plastic case, which may result in malfunction.
4. Do not use any type of chemical or any abrasive powder to clean the cabinet. Use only mild
detergents on a soft, damp cloth to clean the CD-RA195 telephone.
5. The CD-RA195 has built-in surge protection circuits that meet or exceed FCC requirements.
However, an incident such as a lightning strike at or near the telephone lines, could cause
serious damage.
6. If the CD-RA195 is installed in an area with frequent or severe electrical storms, it is suggested
that the telephone be disconnected during these storms or that additional surge suppression
equipment be added to the installation.
7. In the case of trouble with the telephone, do not attempt to repair the telephone yourself. It is
the responsibility of users requiring service to report the need for service to our Service
Department. They will make the necessary arrangements for repair or replacement.
8. If you should have any questions about the operation of your CD-RA195 telephone, you may
contact COBY ELECTRONICS CORP. customer service dept for technical assistance
9. Please register your product online at
No dial tone/phone will not dial out:
Check that the AC power adapter is plugged into a working AC power outlet.
Check all telephone cord connections or try another wall jack.
Do a basic reset of the phone: Disconnect the phone from the wall and remove the battery. Leave
" "
for 30 minutes and then re-install as instructed by the manual.
Can't hear the ring signal:
Check the ringer volume controls; at the lowest level the ring may not be heard.
While on a call, you hear another call on the line or experience radio frequency
interference.
Switch channels to a clear channel.
Check the wiring for bad connections.
Do not use this phone within 20 feet of a working microwave. The microwave produces
frequencies in this range which may cause interference. This interference is normal for all 5.8GHz
phones and should not be considered a product defect.
The caller's name and/or phone number does not appear on the display.
Make sure you have subscribed to Caller ID service from your local telephone company and that
service has been activated.
MESSAGE WAITING AND OTHER FEATURES
key on the handset to stop the page/find
If you venture too far from the base, the handset will beep and the
. Reverse your direction to re-establish connection with the base
"
"TRY AGAIN" .
www.coby.com
26
the
.