Step 5 — Field Fabricate Ductwork - Bryant 580J*04A Installation Instructions Manual

Step 5 — Field Fabricate Ductwork —
return-air static pressure (a negative condition) shall not
exceed 0.35 in. wg (87 Pa) with economizer or 0.45 in. wg
(112 Pa) without economizer. For vertical ducted applica-
tions, secure all ducts to roof curb and building structure.
Do not connect ductwork to unit. Fabricate supply
ductwork so that the cross sectional dimensions are equal
to or greater than the unit supply duct opening dimensions
for the first 18 in. (458 mm) of duct length from the unit
basepan. Insulate and weatherproof all external ductwork,
joints, and roof openings with counter flashing and mastic
in accordance with applicable codes.
Ducts passing through unconditioned spaces must be insu-
lated and covered with a vapor barrier. If a plenum return is
used on a vertical unit, the return should be ducted through the
roof deck to comply with applicable fire codes.
A minimum clearance is not required around ductwork.
CAUTION
Failure to follow this caution may result in damage to roof-
ing materials.
Membrane roofs can be cut by sharp sheet metal edges. Be
careful when placing any sheet metal parts on such roof.
Step 6 — Rig and Place Unit —
do not drop. Spreader bars are required. Rollers may be used to
move unit across a roof. Level by using unit frame as a refer-
ence. See Table 1 and Fig. 6 for additional information.
Lifting holes are provided in base rails as shown in Fig. 6.
Refer to rigging instructions on unit.
Rigging materials under unit (cardboard or wood to prevent
base pan damage) must be removed PRIOR to placing the unit
on the roof curb. When using the standard side drain connec-
tion, ensure the red plug in the alternate bottom connection is
tight. Do this before setting the unit in place. The red drain pan
can be tightened with a 1 / -in. square socket drive extension.
2
"B"
REQUIRED
SPREADER
BARS
MAX WEIGHT
UNIT
LB
580J-04A 772
580J-05A 826
580J-06A 896
580J-07A 1075
NOTES:
1. SPREADER BARS REQUIRED — Top damage will occur if spreader bars are not used.
2. Dimensions in () are in millimeters.
3. Hook rigging shackles through holes in base rail, as shown in detail "A." Holes in base rails are centered around the unit center of gravity. Use wooden top to prevent
rigging straps from damaging unit.
4. Max weight includes the base unit plus shipping pallet plus all available FIOPs which could be on that size unit.
Cabinet
Keep unit upright and
36"- 54"
(914-1371)
"C"
"A"
SEE DETAIL "A"
A
KG LB
350 74.5
375 74.5
406 74.5
489 74.5
Fig. 6 — Rigging Details
For further details see Step 11 — Install External Condensate
Trap and Line on page 14.
Before setting the unit onto the curb, recheck gasketing on
curb.
Failure to follow this caution may result in equipment
damage.
All panels must be in place when rigging. Unit is not
designed for handling by fork truck.
POSITIONING ON CURB — Position unit on roof curb so
that the following clearances are maintained:
clearance between the roof curb and the base rail inside the
front and back, 0.0 in. clearance between the roof curb and the
base rail inside on the duct end of the unit. This will result in
the distance between the roof curb and the base rail inside on
the condenser end of the unit being approximately
(6.4 mm).
Although unit is weatherproof, guard against water from
higher level runoff and overhangs.
Flue vent discharge must have a minimum horizontal clear-
ance of 4 ft (1220 mm) from electric and gas meters, gas regu-
lators, and gas relief equipment. Minimum distance between
unit and other electrically live parts is 48 inches (1220 mm).
Flue gas can deteriorate building materials. Orient unit such
that flue gas will not affect building materials. Locate mechani-
cal draft system flue assembly at least 48 in. (1220 mm) from
an adjacent building or combustible material.
NOTE: Installation of accessory flue discharge deflector kit
will reduce the minimum clearance to combustible material
to 18 in. (460 mm).
After unit is in position, remove rigging skids and shipping
materials.
PLACE ALL SEAL STRIP IN PLACE
BEFORE PLACING UNIT ON ROOF CURB.
DUCT END
DIMENSIONS
B
KG LB
1890 39.0
1890 39.0
1890 39.0
1890 39.0
9
CAUTION
1 / in. (6.4 mm)
4
DETAIL "A"
C
KG LB
990 33.5
990 33.5
990 33.5
990 41.5
1 / in.
4
KG
850
850
850
1055