Table of Contents
Advertisement
ELECTRICAL REQUIREMENTS AND SAFETY
POWER SUPPLY AND MOTOR SPECIFICATIONS
The AC motor used in this saw is a universal, nonreversible
type. See "PRODUCT SPECIFICATIONS" section on
page 2.
WARNING
to a 120 V, 15 A circuit and use a 15 A time delay fuse
ELECTRICAL REQUIREMENTS
DOUBLE INSULATED
The power tool is double insulated to provide a double
thickness or insulation between you and tool's electrical
system. All exposed metal parts are isolated from the
internal metal motor components with protecting insulation.
When servicing, use only identical
replacement parts.
This saw has a plug that looks like the
one shown below:
To reduce the risk of electrical shock, this saw has
a
arized plug (one blade is wider than the other).
This plug will fit in a polarized outlet only one way. If
the plug does not fit fully in the outlet, reverse the plug.
If it is still does not fit, contact a qualified electrician to
install the proper outlet. Do not change the plug in any
way.
WARNING
To avoid electrocution:
1. Use only identical replacement parts when servicing
a tool with double insulation. Servicing should be
performed by a qualified technician.
2. Do not use power tools in wet or damp locations or
expose them to rain or snow.
MOTOR SAFETY PROTECTION
IMPORTANT
To avoid motor damage, the motor should be blown out
or vacuumed frequently to keep sawdust from interfering
with the motor ventilation.
1. Connect this saw to a 120 V circuit. This circuit must
not be less than a #12 wire with a 20 A time lag fuse
or a #14 wire with a 15 A time lag fuse. NOTE: When
using an extension cord on a circuit with a # 14 wire,
the extension cord must not exceed 25 feet in length.
2. If the motor will not start, release the trigger switch
immediately. UNPLUG THE SAW. Check the saw
blade to make sure it turns freely. If the blade is free,
try to start the saw again. If the motor still does not
start, refer to the TROUBLESHOOTING GUIDE.
3. If the tool suddenly stalls while cutting wood, release
the trigger switch, unplug the tool and free the blade
from the wood. The saw may now be started and the
cut finished.
4. FUSES may "bolw" or circuit breakers may trip
frequently if:
a: MOTOR is overload - overloading can occur if you
feed too rapidly or make too many start/stops in a
short time.
b: LINE VOLTAGE is more than 10% above or below
the nameplate voltage rating. For heavy loads, the
voltage at motor terminals must equal the voltage
specified on the nameplate.
c. IMPROPER or dull saw blades are used.
5. Most motor trouble may be traced to loose or incorrect
connections, overload, low voltage or inadequate
power supply wiring. Always check the connections,
the load and supply circuit if the motor doesn't run
well. Check minimum gauge for the length of cord you
are using on the chart below.
GUIDELINES FOR EXTENSION CORDS
Use a proper extension cord. Make sure your extension
cord is good condition. When using an extension cord,
be sure to use one heavy enough to carry the current
your product will draw. An undersized cord will cause a
drop in line voltage, resulting in loss of power and
overheating. The table (on page 9) shows the correct size
to use depending on cord length and nameplate ampere
rating. If in doubt, use the next heavier gauge. The smaller
the gauge number, the heavier the cord.
good condition. Always replace a damaged extension cord
or have it repaired by a qualified person before using it.
Protect your extension cords from sharp objects, excessive
heat and damp or wet areas.
circuit must not be less than a #12 wire with a 20 A time
lag fuse or a #14 wire with a 15 A time lag fuse. NOTE:
When using an extension cord on a circuit with a #14
wire, the extension cord must not exceed 25 feet in length.
Before connecting the tool to the power line, make sure
the switch is in the OFF position and the electric current
is rated the same as the current stamped on the motor
nameplate, running at a lower voltage will damage the
motor.
8
and in
This
Hide quick links:
Advertisement
Table of Contents
