O2 / temperature transmitter / controller (48 pages)
Summary of Contents for Endress+Hauser Cerabar S
Page 1
Operating Instructions – Description of device functions Cerabar S/Deltabar S/Deltapilot S Pressure and Differential pressure transmitters BA274P/00/en/08.06 71027249 valid from Software version 02.10 Hardware version 02.00...
Page 2
® – Operation HistoROM /M-DAT Functional Safety Manual SD190P – Safety function with Cerabar S – The documentation is supplied with the – Behaviour in operation and failure devices showing version "E" in feature 100 – Commissioning and iterative tests "Additional options 1"...
Page 3
Cerabar S/Deltabar S/Deltapilot S Overview documentation Device Documentation Content Remarks Deltabar S Technical Information TI382P Technical data – The documentation is located on the ToF Tool 4 to 20 mA HART CD. The CD is enclosed with every device ordered with the "HistoROM/M-DAT"...
Page 4
Overview documentation Cerabar S/Deltabar S/Deltapilot S Device Documentation Content Remarks Deltapilot S Technical Information TI416P Technical data – The documentation is located on the ToF Tool 4 to 20 mA HART CD. The CD is enclosed with every device ordered with the "HistoROM/M-DAT"...
Page 5
Cerabar S/Deltabar S/Deltapilot S Table of contents Table of contents Notes on use ....6 Finding parameter description using ID numbers . . . 6...
Notes on use Cerabar S/Deltabar S/Deltapilot S Notes on use Section 7 describes all the parameters in order of how they appear in the menu. Sections 4 to 6 provide typical examples of configuration. Sections 1.1 to 1.3 describe ways of finding a certain parameter description more easily.
Page 7
SIM. CURRENT HART MESSAGE ADDITIONAL INFO. PRESSURE – "Pressure" measuring mode PRESSURE – "Level" measuring mode PRESSURE – "Flow" measuring mode LONG TAG NUMBER See Safety Manual SD189P for Deltabar S, SD190P for Cerabar S and SD213P for Deltapilot S.
Page 8
Finding parameter description using ID numbers Cerabar S/Deltabar S/Deltapilot S ID number Parameter name Description, see page GET LRV GET URV MAX. FLOW 52 or 95 UNIT VOLUME – "Linear" level type 71 or 75 UNIT VOLUME – "Pressure Linearized" level type UNIT VOLUME –...
Page 9
Cerabar S/Deltabar S/Deltapilot S Finding parameter description using ID numbers ID number Parameter name Description, see page COUNTER:T > Tmax OPERATING HOURS SIMULATION MODE SIM. PRESSURE NEG. FLOW TOT. 2 MENU DESCRIPTOR ALTERNATE DATA MANUFACTOR ID CORRECTED PRESS. – "Pressure" measuring mode CORRECTED PRESS.
Page 10
Finding parameter description using ID numbers Cerabar S/Deltabar S/Deltapilot S ID number Parameter name Description, see page TOTALIZER 1 UNIT – "Mass" flow type TOTALIZER 2 UNIT – "Mass" flow type TOTALIZER 1 UNIT – "Gas. std. conditions" flow type TOTALIZER 2 UNIT –...
Page 11
MAX PRESS. FLOW LOW FLOW CUT-OFF SET. L. FL. CUT-OFF SET LRV SET URV LINEAR/SQROOT. DAMPING VALUE CONF. PASSWORD TANK VOLUME TANK HEIGHT CURRENT OUTPUT See Safety Manual SD189P for Deltabar S, SD190P for Cerabar S and SD213P for Deltapilot S.
Page 12
→ → OPERATING → → DIAGNOSTICS (562) → SIMULATION → → MESSAGES → → USER LIMITS → → SERVICE (561) → SYSTEM 2 → See Safety Manual SD189P for Deltabar S, SD190P for Cerabar S and for SD213P Deltapilot S.
Note! • See also Operating Instructions Deltabar S (BA270P), Section 6.6 "Differential pressure measurement", Cerabar S (BA271P), Section 6.4 "Pressure measurement" or Deltapilot S (BA332P), Section 6.5 "Pressure measurement". • For a description of the parameters mentioned, see – Page 45, Table 2: MEASURING MODE –...
Note! • See also Operating Instructions Deltabar S (BA270P), Section 6.6 "Differential pressure measurement", Cerabar S (BA271P), Section 6.4 "Pressure measurement" or Deltapilot S (BA332P), Section 6.5 "Pressure measurement". • Due to the orientation of the device, there may be a shift in the measured value, i.e. when the container is empty, the MEASURED VALUE parameter does not display zero.
Page 15
Cerabar S/Deltabar S/Deltapilot S Pressure measurement Description If necessary, select the "Pressure" measuring mode via the MEASURING MODE parameter. On-site display: Menu path: GROUP SELECTION → MEASURING MODE ToF Tool, FieldCare, HART handheld terminal: Menu path: OPERATING MENU → SETTINGS →...
• The tank can be filled or emptied. Note! • See also Operating Instructions for Deltabar S (BA270P) or Cerabar S (BA271P), Section 6.5 "Level measurement" or Deltapilot S (BA332P), Section 6.4 "Level measurement". • The values entered for EMPTY CALIB./FULL CALIB. and SET LRV/SET URV must have a minimum interval of 1% for the "Level Easy Pressure"...
Page 18
Level measurement Cerabar S/Deltabar S/Deltapilot S Description On-site display: Select BASIC SETUP function group. Menu path: GROUP SELECTION → OPERATING MENU → SETTINGS → BASIC SETUP ➁ Select a pressure unit via the PRESS. ENG. UNIT parameter, here mbar for example.
Page 19
Note! • See also Operating Instructions for Deltabar S (BA270P) or Cerabar S (BA271P), Section 6.5 "Level measurement" or Deltapilot S (BA332P), Section 6.4 "Level measurement". • The values entered for EMPTY CALIB./FULL CALIB. and SET LRV/SET URV must have a minimum interval of 1% for the "Level Easy Pressure"...
Page 20
Level measurement Cerabar S/Deltabar S/Deltapilot S Description Select a pressure unit via the PRESS. ENG. UNIT parameter, here mbar for example. Select a volume unit via the OUTPUT UNIT parameter, ➂ 1000 here l (litres) for example.. Select the "Dry" option by means of the CALIBRATION MODE parameter.
• The tank can be filled or emptied. Note! • See also Operating Instructions for Deltabar S (BA270P) or Cerabar S (BA271P), Section 6.5 "Level measurement" or Deltapilot S (BA332P), Section 6.4 "Level measurement". • The values entered for EMPTY CALIB./FULL CALIB., EMPTY PRESSURE/FULL PRESSURE, EMPTY HEIGHT/FULL HEIGHT and SET LRV/SET URV must have a minimum interval of 1% for the "Level Easy Height"...
Page 22
Level measurement Cerabar S/Deltabar S/Deltapilot S Description Select a pressure unit via the PRESS. ENG. UNIT parameter, here mbar for example. ρ · g Select a volume unit via the OUTPUT UNIT parameter, here l (litres) for example.. Select a height unit via the HEIGHT UNIT parameter, ➀...
Page 23
Note! • See also Operating Instructions for Deltabar S (BA270P) or Cerabar S (BA271P), Section 6.5 "Level measurement" or Deltapilot S (BA332P), Section 6.4 "Level measurement". • The values entered for EMPTY CALIB./FULL CALIB., EMPTY PRESSURE/FULL PRESSURE, EMPTY HEIGHT/FULL HEIGHT and SET LRV/SET URV must have a minimum interval of 1% for the "Level Easy Height"...
Page 24
Level measurement Cerabar S/Deltabar S/Deltapilot S Description Select a pressure unit via the PRESS. ENG. UNIT parameter, here mbar for example. ρ · g Select a volume unit via the OUTPUT UNIT parameter, here l (litres) for example.. Select a height unit via the HEIGHT UNIT parameter, ➀...
• The tank can be filled or emptied. Note! • See also Operating Instructions for Deltabar S (BA270P) or Cerabar S (BA271P), Section 6.5 "Level measurement" or Deltapilot S (BA332P), Section 6.4 "Level measurement". • For a description of the parameters mentioned, see –...
Page 26
Level measurement Cerabar S/Deltabar S/Deltapilot S Description On-site display: Select BASIC SETUP function group. Menu path: GROUP SELECTION → OPERATING MENU → SETTINGS → BASIC SETUP ➁ Select a pressure unit via the PRESS. ENG. UNIT parameter, here mbar for example.
Page 27
Note! • See also Operating Instructions for Deltabar S (BA270P) or Cerabar S (BA271P), Section 6.5 "Level measurement" or Deltapilot S (BA332P), Section 6.4 "Level measurement". • Due to the orientation of the device, there may be a shift in the measured value, i.e. when the container is empty, the MEASURED VALUE parameter does not display zero.
Page 28
Level measurement Cerabar S/Deltabar S/Deltapilot S Description Select a pressure unit via the PRESS. ENG. UNIT parameter, here mbar for example. [mA] Select the "Linear" option by means of the LEVEL MODE ➁ parameter. Select the "Volume" option by means of the LIN.
• The tank can be filled. The linearisation characteristic must rise continuously. Note! • See also Operating Instructions for Deltabar S (BA270P) or Cerabar S (BA271P), Section 6.5 "Level measurement" or Deltapilot S (BA332P), Section 6.4 "Level measurement". • For a description of the parameters mentioned, see –...
Page 30
Level measurement Cerabar S/Deltabar S/Deltapilot S Description On-site display: Select BASIC SETUP function group. Menu path: GROUP SELECTION → OPERATING MENU → SETTINGS → BASIC SETUP Select a pressure unit via the PRESS. ENG. UNIT parameter, here mbar for example.
Page 31
Cerabar S/Deltabar S/Deltapilot S Level measurement Description Enter linearisation table (min. 2 points, max. 32 points). [m ] Fill the tank to the height of the 1st point. ➃ LINE-NUMB: confirm value displayed. X-VAL.: the hydrostatic pressure present is displayed.
Page 32
• This is a theoretical calibration, i.e. the points for the linearisation table are known. Note! • See also Operating Instructions for Deltabar S (BA270P) or Cerabar S (BA271P), Section 6.5 "Level measurement" or Deltapilot S (BA332P), Section 6.4 "Level measurement".
Page 33
Cerabar S/Deltabar S/Deltapilot S Level measurement Description On-site display: Select the "Editor table" option by means of the TABLE [m ] SELECTION parameter. ➃ Select the "Manual" option by means of the LIN. EDIT MODE parameter. Select the "New table" option by means of the EDITOR ➄...
• The tank can be filled. The linearisation characteristic must rise continuously. Note! • See also Operating Instructions for Deltabar S (BA270P) or Cerabar S (BA271P), Section 6.5 "Level measurement" or Deltapilot S (BA332P), Section 6.4 "Level measurement". • For a description of the parameters mentioned, see –...
Page 35
Cerabar S/Deltabar S/Deltapilot S Level measurement Description Select the "Height Linearized" option by means of the ➁ ➃ LEVEL MODE parameter. Select the "Height + Volume" option by means of the COMB. MEASURAND parameter. Select the unit for the 1st measured value via the HEIGHT UNIT parameter, here m for example.
Page 36
Level measurement Cerabar S/Deltabar S/Deltapilot S Description Perform linearisation (calibration for the 2nd measured variable) [m ] Change the function group. Menu path: (GROUP SELECTION →) OPERATING MENU → SETTINGS → LINEARISATION Select TANK CONTENT MIN parameter. Specify the minimum tank contents to be expected, here for example.
Page 37
Cerabar S/Deltabar S/Deltapilot S Level measurement Note! For this level type, the measured variables "Height + %", "Height + Volume", "Height + Mass", "%-Height + %", "%-Height + Volume" and "%-Height + Mass" are available. → See Page 79 ff.
Page 38
• This is a theoretical calibration, i.e. the points for the linearisation table are known. Note! • See also Operating Instructions for Deltabar S (BA270P) or Cerabar S (BA271P), Section 6.5 "Level measurement" or Deltapilot S (BA332P), Section 6.4 "Level measurement".
Page 39
Cerabar S/Deltabar S/Deltapilot S Level measurement Description Perform linearisation (calibration for the 2nd measured variable) Change the function group. [m ] Menu path: (GROUP SELECTION →) OPERATING ➅ MENU → SETTINGS → LINEARISATION Select TANK CONTENT MIN parameter. Specify the minimum tank contents to be expected, here for example.
Page 40
Level measurement Cerabar S/Deltabar S/Deltapilot S A level value is assigned to both the lower and upper current value with the SET LRV (→ Page 97) and SET URV (→ Page 98) parameters. You can use the ASSIGN CURRENT parameter (→ Page 113) to specify whether the current output should depict the 1st or 2nd measured variable.
Cerabar S/Deltabar S/Deltapilot S Flow measurement Flow measurement Calibration Example: In this example, a volume flow should be measured in m Note! • The "Flow measurement" measuring mode is only available for the Deltabar S differential pressure transmitter. • See also Operating Instructions BA270P Deltabar S, Section 6.4 "Flow measurement".
Page 42
Flow measurement Cerabar S/Deltabar S/Deltapilot S Note! You can also perform calibration by means of the QUICK SETUP menu. → See Page 52 ff, Table 5: QUICK SETUP menu. Using the FLOW-MEAS. TYPE parameter, you can choose between the following flow types: –...
Cerabar S/Deltabar S/Deltapilot S Flow measurement Totalizers Example: In this example, the volume flow should be totalised and displayed in the unit m . Negative flows should be added to the flow rate. Note! • For a description of the parameters mentioned, see –...
Description of parameters Cerabar S/Deltabar S/Deltapilot S Description of parameters Note! • The following tables list all the parameters as per the menu structure. Each table corresponds to a function group in the menu tree. The overall menu structure is illustrated in Section 9.1.
QUICK SETUP menus and in the BASIC SETUP function group (OPERATING MENU → SETTINGS → BASIC SETUP). Options: • Pressure • Level • Deltabar S: Flow Factory setting: • Cerabar S and Deltabar S: Pressure • Deltapilot S: Level...
RESET parameter (menu path: (GROUP SELECTION →) OPERATING MENU → OPERATION) using the reset code "7864". → For additional information, see the Safety Manual for Deltabar S (SD189), Cerabar S (SD190) or Deltapilot S (SD213P). Options: •...
Page 47
When the measuring mode is changed, no conversion takes place. The device has to be recalibrated if the measuring mode is changed. Prerequisite: • ToF Tool, FieldCare or HART handheld terminal Options: • Pressure • Level • Deltabar S: Flow Factory setting: • Cerabar S and Deltabar S: Pressure • Deltapilot S: Level...
Page 48
– The current value is also corrected. The CALIB. OFFSET parameter displays the resulting pressure difference (offset) by which the MEASURED VALUE was corrected. Prerequisite: • This parameter is displayed for Deltabar S, Cerabar S with gauge pressure sensor and Deltapilot S. Options: • Abort •...
Page 50
– The current value is also corrected. The CALIB. OFFSET parameter displays the resulting pressure difference (offset) by which the MEASURED VALUE was corrected. Prerequisite: • This parameter is displayed for Deltabar S, Cerabar S with gauge pressure sensor and Deltapilot S. Options: • Abort •...
Page 51
Cerabar S/Deltabar S/Deltapilot S Description of parameters Table 4: (GROUP SELECTION →) QUICK SETUP "Level" Parameter name Description FULL CALIB. (315)/(004) Enter level value for the upper calibration point (container full). Entry The container is either completely or almost full. By entering a value for this parameter, you are assigning a level value to the pressure present at the device.
Page 52
Options: • Pressure • Level • Deltabar S: Flow Factory setting: • Cerabar S and Deltabar S: Pressure • Deltapilot S: Level POS. ZERO ADJUST (685) Position adjustment – the pressure difference between zero (set point) and the measured Entry pressure need not be known.
Due to the orientation of the device, there may be a shift in the measured value, i.e. when the container is empty, the measured value does not display zero. Deltabar S and Cerabar S offer three different ways of performing a position adjustment.
Description of parameters Cerabar S/Deltabar S/Deltapilot S Table 6: (GROUP SELECTION →) OPERATING MENU → SETTINGS → POSITION ADJUSTMENT Parameter name Description POS. ZERO ADJUST (685) Position adjustment – the pressure difference between zero (set point) and the measured Entry pressure need not be known.
When the measuring mode is changed, no conversion takes place. The device has to be recalibrated if the measuring mode is changed. Prerequisite: • ToF Tool, FieldCare or HART handheld terminal Options: • Pressure • Level • Deltabar S: Flow Factory setting: • Cerabar S and Deltabar S: Pressure • Deltapilot S: Level...
Page 56
Description of parameters Cerabar S/Deltabar S/Deltapilot S Table 7: (GROUP SELECTION →) OPERATING MENU → SETTINGS → BASIC SETUP "Pressure" Parameter name Description PRESS. ENG. UNIT (060) Select pressure unit. Selection If a new pressure unit is selected, all pressure-specific parameters are converted and displayed with the new unit.
Page 57
Cerabar S/Deltabar S/Deltapilot S Description of parameters Table 7: (GROUP SELECTION →) OPERATING MENU → SETTINGS → BASIC SETUP "Pressure" Parameter name Description GET LRV (309) Set lower range value – reference pressure is present at device. Entry The pressure for the lower current value (4 mA) is present at device. With the "Confirm"...
Description of parameters Cerabar S/Deltabar S/Deltapilot S Measured value GROUP SELECTION LANGUAGE OPERATING MENU SETTINGS DISPLAY POSITION ADJUSTMENT BASIC SETUP EXTENDED SETUP MEASURING MODE Pressure Level Flow LEVEL SELECTION Level Easy Pressure Level Easy Level Standard Height PRESS. ENG. UNIT CUSTOMER UNIT P CUST.
Description of parameters Cerabar S/Deltabar S/Deltapilot S Measured value GROUP SELECTION LANGUAGE OPERATING MENU SETTINGS DISPLAY POSITION ADJUSTMENT BASIC SETUP EXTENDED SETUP MEASURING MODE Pressure Level Flow LEVEL SELECTION Level Easy Pressure Level Easy Height Level Standard PRESS. ENG. UNIT CUSTOMER UNIT P CUST.
Page 63
Cerabar S/Deltabar S/Deltapilot S Description of parameters Table 9: (GROUP SELECTION→ → → → ) OPERATING MENU → → → → SETTINGS → → → → BASIC SETUP "Level", LEVEL SELECTION "Level Easy Height" PRESS. ENG. UNIT (060) Select pressure unit.
Description of parameters Cerabar S/Deltabar S/Deltapilot S Table 9: (GROUP SELECTION→ → → → ) OPERATING MENU → → → → SETTINGS → → → → BASIC SETUP "Level", LEVEL SELECTION "Level Easy Height" FULL HEIGHT (006) Enter height value for the upper calibration point (container full). The unit is selected via Entry the HEIGHT UNIT parameter (→...
Page 67
Cerabar S/Deltabar S/Deltapilot S Description of parameters Table 10: (GROUP SELECTION → ) OPERATING MENU → SETTINGS → BASIC SETUP "Level" Parameter name Description Prerequisite: • MEASURING MODE = level (→ see also Page 45). Note: See also – Page 70 ff, Tables 11 to 13: BASIC SETUP – contd.
Description of parameters Cerabar S/Deltabar S/Deltapilot S Table 10: (GROUP SELECTION → ) OPERATING MENU → SETTINGS → BASIC SETUP "Level" Parameter name Description CUST. UNIT FACT. P (317) Enter conversion factor for a customer-specific pressure unit. The conversion factor must be entered in relation to the SI unit "Pa". → See also Entry CUSTOMER UNIT P.
Page 69
Cerabar S/Deltabar S/Deltapilot S Description of parameters Measured value GROUP SELECTION LANGUAGE OPERATING MENU SETTINGS DISPLAY POSITION ADJUSTMENT BASIC SETUP EXTENDED SETUP MEASURING MODE Pressure Level Flow LEVEL SELECTION PRESS. ENG. UNIT CUSTOMER UNIT P CUST. UNIT FACT. P LEVEL MODE...
Description of parameters Cerabar S/Deltabar S/Deltapilot S Table 11: (GROUP SELECTION →) OPERATING MENU → SETTINGS → BASIC SETUP "Level", LEVEL MODE "Linear" Parameter name Description The following parameters are displayed if you selected the "Linear" option for the LEVEL MODE parameter. For this level type, the measured variable (level, volume, mass or %) is in direct proportion to the measured pressure.
Page 71
Cerabar S/Deltabar S/Deltapilot S Description of parameters Table 11: (GROUP SELECTION →) OPERATING MENU → SETTINGS → BASIC SETUP "Level", LEVEL MODE "Linear" Parameter name Description CUST. UNIT FACT. H (705) Enter conversion factor for a customer-specific level unit. Entry The conversion factor must be entered in relation to the SI unit "m".
Page 72
Description of parameters Cerabar S/Deltabar S/Deltapilot S Table 11: (GROUP SELECTION →) OPERATING MENU → SETTINGS → BASIC SETUP "Level", LEVEL MODE "Linear" Parameter name Description CUST. UNIT FACT. V (607) Enter conversion factor for a customer-specific volume unit. Entry The conversion factor must be entered in relation to the SI unit "m...
Page 73
Cerabar S/Deltabar S/Deltapilot S Description of parameters Table 11: (GROUP SELECTION →) OPERATING MENU → SETTINGS → BASIC SETUP "Level", LEVEL MODE "Linear" Parameter name Description CUST. UNIT FACT. M (703) Enter conversion factor for a customer-specific mass unit. Entry The conversion factor must be entered in relation to the SI unit "kg".
Page 74
Description of parameters Cerabar S/Deltabar S/Deltapilot S Table 11: (GROUP SELECTION →) OPERATING MENU → SETTINGS → BASIC SETUP "Level", LEVEL MODE "Linear" Parameter name Description EMPTY PRESSURE (710) Displays the pressure value for the lower calibration point (container empty).
Description of parameters Cerabar S/Deltabar S/Deltapilot S Table 11: (GROUP SELECTION →) OPERATING MENU → SETTINGS → BASIC SETUP "Level", LEVEL MODE "Linear" Parameter name Description HEIGHT UNIT (708) Select level unit. Selection Prerequisite: • LIN. MEASURAND = % (Level), CALIBRATION MODE = Dry Options: •...
Page 77
Cerabar S/Deltabar S/Deltapilot S Description of parameters Table 11: (GROUP SELECTION →) OPERATING MENU → SETTINGS → BASIC SETUP "Level", LEVEL MODE "Linear" Parameter name Description 100% POINT (813) Enter level value for 100% point. Entry Prerequisite: • LIN. MEASURAND = % (Level), CALIBRATION MODE = Dry Example: –...
Page 78
Description of parameters Cerabar S/Deltabar S/Deltapilot S Measured value GROUP SELECTION LANGUAGE OPERATING MENU SETTINGS DISPLAY POSITION ADJUSTMENT BASIC SETUP EXTENDED SETUP MEASURING MODE Pressure Level Flow LEVEL SELECTION PRESS. ENG. UNIT PRESS. ENG. UNIT CUSTOMER UNIT P CUST. UNIT FACT. P...
Description of parameters Cerabar S/Deltabar S/Deltapilot S Table 12: (GROUP SELECTION →) OPERATING MENU → SETTINGS → BASIC SETUP "Level", LEVEL MODE "Pressure Linearized" Parameter name Description MASS UNIT (709) Select mass unit. Selection Prerequisite: • LINd. MEASURAND = Pressure and Mass Options: •...
Cerabar S/Deltabar S/Deltapilot S Description of parameters Table 12: (GROUP SELECTION →) OPERATING MENU → SETTINGS → BASIC SETUP "Level", LEVEL MODE "Pressure Linearized" Parameter name Description HYDR. PRESS MAX. (761) Enter the maximum hydrostatic pressure to be expected. Entry The input limits for the calibration (editing limits) are derived from the value entered.
Page 82
Description of parameters Cerabar S/Deltabar S/Deltapilot S Measured value GROUP SELECTION LANGUAGE OPERATING MENU SETTINGS DISPLAY POSITION ADJUSTMENT BASIC SETUP EXTENDED SETUP MEASURING MODE Pressure Level Flow LEVEL SELECTION PRESS. ENG. UNIT CUSTOMER UNIT P CUST. UNIT FACT. P LEVEL MODE...
Cerabar S/Deltabar S/Deltapilot S Description of parameters Table 13: (GROUP SELECTION →) OPERATING MENU → SETTINGS → BASIC SETUP "Level", LEVEL MODE "Height Linearized" Parameter name Description The following parameters are displayed if you selected the "Height Linearized" option for the LEVEL MODE parameter.
Page 84
Description of parameters Cerabar S/Deltabar S/Deltapilot S Table 13: (GROUP SELECTION →) OPERATING MENU → SETTINGS → BASIC SETUP "Level", LEVEL MODE "Height Linearized" Parameter name Description CUSTOMER UNIT H (706) Enter text (unit) for customer-specific level unit. You can enter a maximum of eight alphanumeric characters here. → See also CUST.
Page 85
Cerabar S/Deltabar S/Deltapilot S Description of parameters Table 13: (GROUP SELECTION →) OPERATING MENU → SETTINGS → BASIC SETUP "Level", LEVEL MODE "Height Linearized" Parameter name Description CUSTOMER UNIT V (608) Enter text (unit) for customer-specific volume unit. You can enter a maximum of eight alphanumeric characters here. → See also CUST.
Description of parameters Cerabar S/Deltabar S/Deltapilot S Table 13: (GROUP SELECTION →) OPERATING MENU → SETTINGS → BASIC SETUP "Level", LEVEL MODE "Height Linearized" Parameter name Description CUSTOMER UNIT M (704) Enter text (unit) for customer-specific mass unit. You can enter a maximum of eight alphanumeric characters here. → See also CUST.
Page 87
Cerabar S/Deltabar S/Deltapilot S Description of parameters Table 13: (GROUP SELECTION →) OPERATING MENU → SETTINGS → BASIC SETUP "Level", LEVEL MODE "Height Linearized" Parameter name Description CALIBRATION MODE (392) Select the calibration mode for the calibration of the 1st measured variable.
Page 88
Description of parameters Cerabar S/Deltabar S/Deltapilot S Table 13: (GROUP SELECTION →) OPERATING MENU → SETTINGS → BASIC SETUP "Level", LEVEL MODE "Height Linearized" Parameter name Description DENSITY UNIT (812) Select density unit. Selection Prerequisite: • COMB. MEASURAND = %-Height and %, CALIBRATION MODE = Dry •...
Page 89
Cerabar S/Deltabar S/Deltapilot S Description of parameters Table 13: (GROUP SELECTION →) OPERATING MENU → SETTINGS → BASIC SETUP "Level", LEVEL MODE "Height Linearized" Parameter name Description CUSTOMER UNIT H (706) Enter text (unit) for customer-specific level unit. Entry You can enter a maximum of eight alphanumeric characters here.
Page 90
Description of parameters Cerabar S/Deltabar S/Deltapilot S Table 13: (GROUP SELECTION →) OPERATING MENU → SETTINGS → BASIC SETUP "Level", LEVEL MODE "Height Linearized" Parameter name Description ZERO POSITION (814) Enter value for level offset. Entry If the measurement should not start at the mounting location of the device, e.g. for containers with a sump, carry out zero point shift (level offset).
Cerabar S/Deltabar S/Deltapilot S Description of parameters Measured value GROUP SELECTION LANGUAGE OPERATING MENU SETTINGS DISPLAY POSITION ADJUSTMENT BASIC SETUP EXTENDED SETUP MEASURING MODE Pressure Level Flow PRESS. ENG. UNIT CUSTOMER UNIT P CUST. UNIT FACT. P FLOW-MEAS. TYPE Mass Volume norm cond.
Page 92
Options: • Pressure • Level • Deltabar S: Flow Factory setting: • Cerabar S and Deltabar S: Pressure • Deltapilot S: Level PRESS. ENG. UNIT (060) Select pressure unit. Selection If a new pressure unit is selected, all pressure-specific parameters are converted and displayed with the new unit.
Cerabar S/Deltabar S/Deltapilot S Description of parameters Table 14: (GROUP SELECTION →) OPERATING MENU → SETTINGS → BASIC SETUP "Flow" Parameter name Description CUST. UNIT FACT. P (317) Enter conversion factor for a customer-specific pressure unit. The conversion factor must be entered in relation to the SI unit "Pa". → See also Entry CUSTOMER UNIT P.
Description of parameters Cerabar S/Deltabar S/Deltapilot S Table 14: (GROUP SELECTION →) OPERATING MENU → SETTINGS → BASIC SETUP "Flow" Parameter name Description STD. FLOW UNIT (660) Select standard volume flow unit. Selection When a new flow unit is selected, all flow-specific parameters are converted and displayed with the new unit within a flow mode (FLOW-MEAS.
Cerabar S/Deltabar S/Deltapilot S Description of parameters Table 14: (GROUP SELECTION →) OPERATING MENU → SETTINGS → BASIC SETUP "Flow" Parameter name Description CUST. UNIT FACT. F (609) Enter conversion factor for a customer-specific flow unit. The conversion factor must be Entry entered in relation to an appropriate SI unit, e.g.
Description of parameters Cerabar S/Deltabar S/Deltapilot S Measured value GROUP SELECTION LANGUAGE OPERATING MENU SETTINGS DISPLAY POSITION ADJUSTMENT BASIC SETUP EXTENDED SETUP Pressure Level Flow TEMP. ENG. UNIT TEMP. ENG. UNIT TEMP. ENG. UNIT ADJUST DENSITY LOW FLOW CUT-OFF PROCESS DENSITY SET L.
Cerabar S/Deltabar S/Deltapilot S Description of parameters Table 16: (GROUP SELECTION →) OPERATING MENU → SETTINGS → EXTENDED SETUP "Level" Parameter name Description DENSITY UNIT (001)/(812) Select density unit. Options Options: • g/cm • kg/dm • kg/m • US lb/in •...
Description of parameters Cerabar S/Deltabar S/Deltapilot S Table 16: (GROUP SELECTION →) OPERATING MENU → SETTINGS → EXTENDED SETUP "Level" Parameter name Description SET URV (763) Enter value for the upper current value (20 mA). Entry Prerequisite: • LEVEL MODE = Pressure Linearized or Height Linearized Note! •...
Cerabar S/Deltabar S/Deltapilot S Description of parameters Table 17: (GROUP SELECTION →) OPERATING MENU → SETTINGS → EXTENDED SETUP "Flow" Parameter name Description SET. L. FL. CUT-OFF (323) Enter switch-off point of low flow cut-off. Entry The hysteresis between the switch-on point and the switch-off point is always 1 % of the end flow value.
Description of parameters Cerabar S/Deltabar S/Deltapilot S Measured value GROUP SELECTION LANGUAGE OPERATING MENU SETTINGS DISPLAY Level measuring POSITION ADJUSTMENT LINEARIZATION mode only TANK CONTENT MIN TANK CONTENT MAX TABLE SELECTION Editor Table Measuring Table LIN. EDIT MODE MEASURING TABLE...
Cerabar S/Deltabar S/Deltapilot S Description of parameters Table 18: (GROUP SELECTION →) OPERATING MENU → SETTINGS → LINEARISATION – on-site operation Parameter name Description TANK CONTENT MAX Enter the maximum tank contents to be expected. (713) The input limits for the subsequent calibration (editing limits) are derived from the value Entry entered.
Page 102
Description of parameters Cerabar S/Deltabar S/Deltapilot S Table 18: (GROUP SELECTION →) OPERATING MENU → SETTINGS → LINEARISATION – on-site operation Parameter name Description EDITOR TABLE Enter table in the "Semiautomatic" editing mode. Entry ("Semiautomatic" edit A linearisation table must have at least 2 points and may not have more than 32 points. A mode) point consists of LINE-NUMB, X-VAL.
Cerabar S/Deltabar S/Deltapilot S Description of parameters Table 18: (GROUP SELECTION →) OPERATING MENU → SETTINGS → LINEARISATION – on-site operation Parameter name Description MEASURING TABLE (549) A point of the linearisation table saved (measuring table) appears on the display Display The parameter first displays the first point of the linearisation table.
Page 104
Description of parameters Cerabar S/Deltabar S/Deltapilot S Table 19: (GROUP SELECTION →) OPERATING MENU → SETTINGS → LINEARISATION – ToF Tool, HART handheld terminal Parameter name Description TANK CONTENT MIN Enter the minimum tank contents to be expected. Entry The input limits for the calibration (editing limits) are derived from the value entered. The closer the value entered corresponds to the minimum tank content to be expected, the more accurate the measurement result.
Page 106
Description of parameters Cerabar S/Deltabar S/Deltapilot S Table 19: (GROUP SELECTION →) OPERATING MENU → SETTINGS → LINEARISATION – ToF Tool, HART handheld terminal Parameter name Description EDITOR TABLE Select the function for the editor table. Options Prerequisite: • TABLE SELECTION = Editor table Options: •...
Page 107
Cerabar S/Deltabar S/Deltapilot S Description of parameters Measured value GROUP SELECTION LANGUAGE OPERATING MENU SETTINGS DISPLAY Flow measuring POSITION ADJUSTMENT TOTALIZER SETUP mode only TOTALIZER 1 UNIT TOT. 1 USER UNIT FACT. U. U. TOTAL. 1 NEG. FLOW TOT. 1...
Description of parameters Cerabar S/Deltabar S/Deltapilot S Table 20: (GROUP SELECTION →) OPERATING MENU → SETTINGS → TOTALIZER SETUP Parameter name Description TOT. 1 USER UNIT (627) Enter text (unit) for customer-specific unit for totalizer 1. You can enter a maximum of eight alphanumeric characters here. → See also FACT. U.
Cerabar S/Deltabar S/Deltapilot S Description of parameters Table 20: (GROUP SELECTION →) OPERATING MENU → SETTINGS → TOTALIZER SETUP Parameter name Description TOT. 2 USER UNIT (628) Enter text (unit) for customer-specific unit for totalizer 2. → See also TOT. 1 USER UNIT.
Parameter name Description MENU DESCRIPTOR (419) Specify contents for the main line of the on-site display in the measuring mode. → See also Operating Instructions BA270P (Deltabar S), BA271P (Cerabar S) or BA332P Selection (Deltapilot S), Section 5.1 "On-site display". Options: •...
• Hold meas. value: last measured value is kept. • Min. alarm (–10%): 3.6 mA → See also this table SET MAX. ALARM and Operating Instructions BA270P (Deltabar S), BA271P (Cerabar S) or BA332P (Deltapilot S), Section 8.2.1. "Setting current output for alarm". Factory setting:...
Cerabar S/Deltabar S/Deltapilot S Description of parameters Table 22: (GROUP SELECTION →) OPERATING MENU → OUTPUT Parameter name Description ALT. CURR. OUTPUT (597) Set current output if sensor limits undershot or overshot. Selection Options: • Normal: the current output assumes the value set via the OUTPUT FAIL MODE and SET MAX.
Displays the device identification number in decimal numerical format, Display here Deltabar S: 23 Prerequisite: • Deltabar S differential pressure transmitter DEVICE TYPE (802) Displays the device identification number in decimal numerical format, Display here Cerabar S: 24 Prerequisite: • Pressure transmitter Cerabar S...
Cerabar S/Deltabar S/Deltapilot S Description of parameters Table 23: (GROUP SELECTION →) OPERATING MENU → TRANSMITTER INFO → HART DATA Parameter name Description DEVICE TYPE (002) Displays the device identification number in decimal numerical format, Display here Deltapilot S: 26 Prerequisite: •...
Description of parameters Cerabar S/Deltabar S/Deltapilot S Table 23: (GROUP SELECTION →) OPERATING MENU → TRANSMITTER INFO → HART DATA Parameter name Description SECONDARY VAL. IS Select second process value. You can choose between the following process values depending on the measuring mode selected: –...
INSERT PIN No. parameter, you can only unlock operation again by means of this parameter. (→ INSERT PIN NO, see Page 125.) → See also Operating Instructions BA270P (Deltabar S), BA271P (Cerabar S) or BA332P (Deltapilot S), Section 5.9 "Locking/unlocking operation".
Description of parameters Cerabar S/Deltabar S/Deltapilot S Table 25: (GROUP SELECTION →) OPERATING MENU → TRANSMITTER INFO → PROCESS CONNECTION Parameter name Description MAT. PROC. CONN. + For selecting and displaying the material of the process connection (P+). → See also parameter description for MAT. PROC. CONN. -...
Displays the membrane material Display Factory setting: As per version in the order code → For Deltabar S, see Technical Information TI382P, for Cerabar S, see Technical Information TI383P or for Deltapilot S, see Technical Information TI416P, "Ordering information" section.
Description of parameters Cerabar S/Deltabar S/Deltapilot S Table 26: (GROUP SELECTION →) OPERATING MENU → TRANSMITTER INFO → SENSOR DATA (all measuring modes) Parameter name Description FILLING FLUID (366) Displays the filling fluid. Display Tmin SENSOR (368) Displays the lower nominal temperature limit of the sensor.
Cerabar S/Deltabar S/Deltapilot S Description of parameters Table 27: (GROUP SELECTION →) OPERATING MENU → PROCESSINFO → PROCESS VALUES "Pressure" Parameter name Description MEASURED VALUE (679) Displays the measured value In the "Pressure" measuring mode, this value corresponds to the PRESSURE parameter.
Description of parameters Cerabar S/Deltabar S/Deltapilot S Table 28: (GROUP SELECTION →) OPERATING MENU → PROCESSINFO → PROCESS VALUES "Level" Parameter name Description CORRECTED PRESS. (434) Displays the measured pressure after sensor trim and position adjustment and before damping. → See also PRESSURE diagram.
Cerabar S/Deltabar S/Deltapilot S Description of parameters Table 29: (GROUP SELECTION →) OPERATING MENU → PROCESSINFO → PROCESS VALUES "Flow" Parameter name Description SUPPRESSED FLOW (375) Displays the current flow. Depending on the flow mode selected (→ FLOW-MEAS. Display TYPE), a volume flow, mass flow, standard volume flow or corrected volume flow is displayed.
Description of parameters Cerabar S/Deltabar S/Deltapilot S Table 30: (GROUP SELECTION →) OPERATING MENU → PROCESSINFO → PEAK HOLD INDICATOR Parameter name Description RESET PEAKHOLD (382) This parameter lists all the peak hold indicator parameters that can be reset. You can Selection select the peak hold indicators you want to reset.
Parameter name Description ENTER RESET CODE (047) Reset parameters completely or partially to factory values or delivery status. → See also Operating Instructions BA270P (Deltabar S), BA271P (Cerabar S) or BA332P Entry (Deltapilot S), Section 5.10 "Factory setting" (reset). Factory setting: OPERATING HOURS (409) Displays the hours of operation.
Table 31: (GROUP SELECTION →) OPERATING MENU → OPERATING Parameter name Description HistoROM CONTROL (832) For selecting the direction for copying the data. → See also Operating Instructions BA270P (Deltabar S), BA271P (Cerabar S) or BA332P Selection ® (Deltapilot S), Section 5.5. "HistoROM /M-DAT (optional)".
Description of parameters Cerabar S/Deltabar S/Deltapilot S Table 33: (GROUP SELECTION →) OPERATING MENU → DIAGNOSTICS → MESSAGES Parameter name Description ACK. ALARM (500) Acknowledge alarm. Selection Prerequisite: • ACK. ALARM MODE = on Options: • Abort • Confirm The cause of the alarm must be eliminated, the message must be acknowledged via the ACK.
Cerabar S/Deltabar S/Deltapilot S Description of parameters Table 34: (GROUP SELECTION →) OPERATING MENU → DIAGNOSTICS → USER LIMITS Parameter name Description Pmin ALARM WINDOW Customer-specific process monitoring – enter lower pressure limit. (332) You can use the SELECT ALARMTYPE parameter to enter how the device responds if the Entry operating pressure undershoots the specified value.
Description of parameters Cerabar S/Deltabar S/Deltapilot S Table 35: (GROUP SELECTION →) OPERATING MENU → SERVICE → SYSTEM 2 Parametername Beschreibung CURR. TRIM 4mA (045) Enter current value for the lower point (4 mA) of the current output trim line.
• The ALARM STATUS (→ Page 127) parameter shows the message with the highest priority. → See "Priority" column. Note! • For support and further information, please contact Endress+Hauser Service. • → See also Section 8.4, 8.5 and 8.6. Code...
Page 132
– Block off electromagnetic effects or than specifications in the technical eliminate source of disturbance. data. → See Technical Information TI382P (Deltabar S), TI383P (Cerabar S) or TI416P (Deltapilot S). – Main electronics defect. – Replace main electronics. – Sensor defect. – Replace sensor.
Page 133
– HistoROM does not have any data. – Copy suitable data to the HistoROM. (→ See also Operating Instructions BA270P (Deltabar S) or BA271P (Cerabar S), Section 5.5.1 "Copying configuration data".) 703 (A703) Alarm B>Measurement error – Fault in the main electronics.
Page 134
Trouble-shooting Cerabar S/Deltabar S/Deltapilot S Code Error type/ Message/description Cause Measure Priority NA 64 707 (A707) Alarm B>X-VAL. of lin. table out of edit – At least one X-VALUE in the – Carry out calibration again. (→ See limits. linearisation table is either below the also these Operating Instructions, value for HYDR.
Page 135
→ See Technical Information TI382P (Deltabar S), TI383P (Cerabar S) or TI416P (Deltapilot S). – Sensor or main electronics defect. – Replace sensor or main electronics. 726 (E726) Error C>Sensor temperature error -...
Page 136
Trouble-shooting Cerabar S/Deltabar S/Deltapilot S Code Error type/ Message/description Cause Measure Priority NA 64 730 (E730) Error C>LRV user limits exceeded – Pressure measured value has – Check system/pressure measured undershot the value specified for the value. Factory Pmin ALARM WINDOW parameter.
Page 137
– Perform reset (Code 7864) and carry data. → See Technical Information out calibration again. TI382P (Deltabar S), TI383P (Cerabar S) or TI416P (Deltapilot S). This message normally only appears briefly. – Cable connection sensor – main – Check cable connection and repair if electronics disconnected.
Trouble-shooting Cerabar S/Deltabar S/Deltapilot S Response of outputs to errors The device differentiates between the error types Alarm, Warning and Error. → See also Section 8.1 "Messages" und Page 112 ff, Table 20: OUTPUT and Page 112 ff, Table 31: MESSAGES the following table and Page 131, Section 8.1 "Messages".
Cerabar S/Deltabar S/Deltapilot S Appendix Confirming messages Depending on the settings for the ALARM DISPL. TIME (→ Page 128) and ACK. ALARM MODE (→ Page 127) parameters, the following measures should be taken to clear a message: Settings Measures – ALARM DISPL. TIME = 0 s –...
Page 140
DAMPING VALUE 1) Display via on-site display only 2) Display via ToF Tool, FieldCare and HART Handheld terminal only 3) Cerabar S with gauge pressure sensor, Deltabar S or Deltapilot S 4) Cerabar S with absolut pressure sensor There are parameters that are only displayed if other parameters are appropriately configured.
Page 141
Cerabar S/Deltabar S/Deltapilot S Appendix BASIC SETUP MEASURING MODE Deltabar S only Pressure Level Flow PRESS. ENG. UNIT PRESS. ENG. UNIT LEVEL SELECTION CUSTOMER UNIT P CUSTOMER UNIT P Level Easy Pressure Level Easy Height Level Standard CUST. UNIT FACT. P CUST.
Page 142
Appendix Cerabar S/Deltabar S/Deltapilot S Continuation BASIC SETUP "Level", Height Volume Mass see also the previous page LEVEL SELECTION = HEIGHT UNIT UNIT VOLUME MASS UNIT Level Standard CUSTOMER UNIT V CUSTOMER UNIT M CUTOMER UNIT H PRESS. ENG. UNIT CUST.
Page 143
Cerabar S/Deltabar S/Deltapilot S Appendix EXTENDED SETUP LINEARISATION LINEARISATION TOTALIZER SETUP Level measuring Level measuring Flow measuring mode only mode only mode only (Deltabar S only) Display via on-site Display via ToF Tool or display only HART handheld terminal only...
Page 144
Appendix Cerabar S/Deltabar S/Deltapilot S OUTPUT SAFETY CONFIRM. DISPLAY OUTPUT CURRENT SAFETY LOCK MENU DESCRIPTOR CURR. CHARACT. SAFETY PASSWORD MAIN DATA FORMAT DIGIT SETS ALTERNATE DATA OUTPUT FAIL MODE ALT. CURR. OUTPUT CURRENT OUTPUT LANGUAGE ACK. ALARM MODE DISPLAY CONTRAST SET MAX.
Page 145
Cerabar S/Deltabar S/Deltapilot S Appendix TRANSMITTER INFO PROCESS INFO HART DATA TRANSMITTER DATA PROCESS CONNECTION SENSOR DATA PROCESS VALUE PEAK HOLD INDICATOR Pressure Level Flow BUS ADDRESS DEVICE SERIAL No Pmax PROC. CONN. SENSOR SER. NO. MEASURED VALUE MEASURED VALUE MEASURED VALUE COUNTER:P >...
Page 146
Appendix Cerabar S/Deltabar S/Deltapilot S OPERATION DIAGNOSTICS SERVICE SIMULATION MESSAGES USER LIMITS SYSTEM 2 ENTER RESET CODE SIMULATION MODE ALARM STATUS Pmin ALARM WINDOW CURR. TRIM 4mA OPERATING HOURS LAST DIAG. CODE Pmax ALARM WINDOW CURR. TRIM 20mA INSERT PIN NO ACK.
Page 147
Cerabar S/Deltabar S/Deltapilot S Appendix...