Table of Contents
Advertisement
Feb. 2005
ERROR MESSAGES
Blank Disc!
Cause:
Disc in the CD-R/RW drive contains no data.
Action:
Load a CD-R/RW disc that has data written on it.
Cannot Punch In for CD-R/RW!
Cause:
You attempted to press [REC] after you had already pressed [PLAY]
when directly bouncing tracks to a CD-R/RW disc .
Action:
To bounce tracks directly to a CD-R/RW disc, first press [REC] and
then [PLAY].
Cannot Select Same Track!
Cause:
You attempted to select the same track more than once during Track
Edit , WAV/AIFF Export , or another procedure.
Action:
Select a different track.
CD Full!
Cause 1: The CD-R/RW disc is full, and no more data can be written to it.
Action 1: Reduce the amount of data to be written, then try again.
Cause 2: When creating an audio CD, the total time of the tracks exceeds the
capacity of the CD-R/RW disc.
Action 2: Reduce the number of songs to be written, then try again.
CD Read Error!
Cause:
An error occurred while reading data from the CD-R/RW disc.
Action 1: This may be due to a low-quality or dated disc. Try using a new CD-
R/RW disc.
Action 2: The CD-R/RW drive's pickup may by dirty. Try cleaning the pickup
(p. 8).
CD Write Error!
Cause:
An error occurred while writing data to the CD-R/RW disc.
Action 1: This may be due to a low-quality or dated disc. Try using a new CD-
R/RW disc.
Action 2: The CD-R/RW drive's pickup may by dirty. Try cleaning the pickup
(p. 8).
Clock Error!
Cause:
Reception of the MIDI timing clock was interrupted during
recording of the Sync Track.
Action:
Make sure that the MIDI cable is connected correctly and check
whether the external MIDI device was turned off during the
recording process.
Data Too Large!
Cause 1: You attempted to import an SMF exceeding 250 KB.
Action 1: Prepare the SMF to be loaded so that it is no more than 250 KB.
Cause 2: You attempted to create a loop phrase using waveform data thirty
minutes or longer.
Action 2: Use waveform data less than thirty minutes long.
Data Too Short!
Cause 1: You attempted to load a waveform file lasting 0.5 seconds or less.
Action 1: Prepare the waveform file so that it is longer than 0.5 seconds.
Cause 2: You attempted to write an audio CD with a track that is less than
four seconds in length.
Action 2: Prepare tracks being written to audio CDs so that they are at least
four seconds long.
Cause 3: You attempted to create a loop phrase using waveform data less
than 0.5 seconds in length.
Action 3: Use waveform data that is at least 0.5 seconds long.
Data Type Not Supported!
Cause:
You are attempting to load a file or disc in an incompatible format.
Action:
Use a file in a compatible format.
Disc Not Ready!
Cause:
There is no CD-R/RW disc in the drive.
Action:
Place a CD-R/RW disc in the drive.
Drive Busy!
Cause:
The data on the hard disk has become fragmented, causing delays in
reading and writing data.
Action 1: Reduce the number of tracks that are played back simultaneously.
Use track bouncing (or other means) to combine tracks, or erase or
cut data from tracks which you do not need to play back, and then
try the playback again.
Action 2: Reduce the number of tracks that are being recorded
simultaneously.
Action 3: If using the drum and bass patterns or loop phrases, press the Track
button, causing the button's indicator to go out.
Action 4: First, back up the data on the hard disk to a CD-R/RW disc , then
after initializing the hard disk (p. 285), recover the data from the CD-
R/RW disc .
In cases of unfavorable disk access conditions, such as when track editing,
punch-in recording, etc. is used to connect phrases (musical data) of
several seconds.
Event Memory Full!
Cause:
The BR-1200CD has used up all the events that can be handled by
one song.
Action:
Perform the Song Optimize operation.
Finalized Disc!
Cause:
Data has already been written to the CD-R/RW disc, and the data
has been finalized.
Action:
Place a CD-R/RW disc that has not been finalized in the drive.
HDD Damaged! Can't Access HDD.
Cause:
Data could not be read from or written to the hard disk.
Action:
There is a possibility that the hard disk has been damaged. Shut
down the BR-1200CD as instructed and send it for repair.
HDD Full!
Cause:
There is insufficient free space on the hard disk.
Action 1: Erase unneeded data.
Action 2: Perform the Song Optimize operation.
HDD Read Error!
Cause:
An error occurred while reading data from the hard disk.
Action:
The hard disk must be initialized.
HDD Write Error!
Cause:
An error occurred while writing data to the hard disk.
Action:
The hard disk must be initialized. Also, the song data you had been
attempting to save will be lost.
Insert Disc #***!
Cause:
During recovery of backup data located on multiple CD-R/RW
discs, the disc of the requested number was not placed in the drive.
Action:
Place the disc with the requested number in the drive.
BR-1200CD
47
Advertisement
Table of Contents
