Summary of Contents for Poulan Pro Poulan Pro 952711882
Page 1
AVERTISSEMENT: Lire le manuel d’instructions et bien respecter tous les avertisse- ments et toutes les instructions de sécurité. Tout défaut de le faire pourrait entraîner des blessures graves. Poulan PRO 1030 Stevens Creek Road Augusta, GA 30907 Instruction Manual PP446ET...
IDENTIFICATION OF SYMBOLS DANGER! This pruner can be dangerous! Careless or im- proper use can cause serious or even fatal injury. Always wear appropriate ear protection, eye protection and head protection. DANGER! Falling objects can cause severe head injury. Wear head protection when operating this unit.
Page 3
Never use flailing de- vices with any attachment. This unit (when used with supplied line trimmer attachment) is designed for line trimmer use only. Use of any other accessories with line trimmer attach- ment will increase the risk of injury.
S Maintain unit according to recommended procedures. Keep cutting line at proper length. S Use only 0.080″ (2 mm) diameter Poulan PRO brand line. Never use wire, rope, string, etc. S Install required shield properly before using the unit.
could close a cut and pinch or fall into chain. S Use the Reduced- -Kickback Guide Bar and Low- -Kickback Chain specified for your unit. MAINTAIN CONTROL S Keep a good, firm grip on the pruner with both hands when the engine is running and don’t let go.
Blade can thrust violently away from material it does not cut. Blade thrust can cause amputation of arms or legs. WARNING: Do not use trimmer head as a fastening device for the blade. WARNING: The blade continues to spin after the throttle is released or engine is turned off.
Page 7
bent, warped, cracked, broken or damaged in any other way. S Install required shield properly before using the unit. Use the metal shield for all metal blade use. WARNING: Only use brushcutter at- tachments that provide a metal shield with proboscis nose.
Page 8
TOOLS REQUIRED S Hex wrench (provided) INSTALLING PRUNER OR LINE TRIMMER ATTACHMENTS CAUTION: When removing or installing at- tachments, place the unit on a flat surface for stability. 1. Loosen the coupler by turning the knob counterclockwise.
Page 9
1. Loosen wing nut on handle. 2. Rotate the handle on the shaft to an up- right position; retighten wing nut. ATTACHING SHIELD (FOR LINE TRIMMER ATTACHMENT) WARNING: The shield must be prop- erly installed. The shield provides partial protec-...
See CHAIN TENSION in the SERVICE AND AD- JUSTMENTS section. Poulan/WEED EATER brand synthetic oil is recommended. Mix gasoline and oil at a ratio of 40:1. A 40:1 ratio is obtained by mixing 3.2 ounces (95 ml) of oil with 1 gallon (4 liters) of unleaded gasoline.
Page 11
Poulan or Poulan PRO oil resists high temperature thinning. If Poulan or Poulan PRO bar and chain oil is not available, use a good grade SAE 30 oil.
Coupler LOOSEN Lower Attachment TIGHTEN Knob 2. Press and hold the locking/release button. Locking/Release Button Coupler Upper Shaft Lower Attachment 3. While securely holding the engine and upper shaft, pull the attachment straight out of the coupler. INSTALLING OPTIONAL ATTACH- MENTS 1.
TRIMMER LINE ADVANCE The trimmer line will advance approximately 2 inches (5 cm) each time the bottom of the trimmer head is tapped on the ground with the engine running at full throttle. The most efficient line length is the maximum length allowed by the line limiter.
Page 14
S Hold the trimmer head parallel to and above the grassy area. S Tap the bottom of the trimmer head lightly on the ground one time. Approximately 2 inches (5 cm) of line will be advanced with each tap. Always tap the trimmer head on a grassy area.
If any dealer other than an authorized service dealer performs work on the product, Poulan PRO may not pay for repairs under warranty. It is your re- sponsibility to maintain and perform general maintenance.
1. Clean the cover and the area around it to keep dirt from falling into the carburetor chamber when the cover is removed. 2. Remove parts by pressing button to re- lease air filter cover. NOTE: To avoid creating a fire hazard or producing harmful evaporative emissions, do not clean filter in gasoline or other flammable solvent.
2. Clean entire surface of hub and spool. 3. Replace with a pre-wound spool, or cut two lengths of 12-1/2 feet of 0.080″ (2 mm) di- ameter Poulan PRO brand line. WARNING: Never use wire, rope, string, etc., which can break off and become a dangerous missile.
Page 18
WARNING: Keep others away when making idle speed adjustments. The chain will be moving during most of this procedure. Wear your protective equipment and observe all safety precautions. After making adjust- ments, the chain must not move at idle speed. The carburetor has been carefully set at the factory.
Page 19
WARNING: Always stop unit and disconnect spark plug before performing all of the recommended remedies below except remedies that require operation of the unit. TROUBLE CAUSE Engine will not 1. ON/OFF switch in start. OFF position. 2. Engine flooded. 3. Fuel tank empty. 4.
LIMITATIONS OF INCIDENTAL OR CON- SEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSION MAY NOT APPLY TO YOU. The policy of Poulan PRO is to continuously improve its products. Therefore, Poulan PRO reserves the right to change, modify, or discontinue models, designs, specifications, and accessories of all products at any time without notice or obligation to any purchaser.
ADD- - ON OR MODIFIED PARTS: The use of add- -on or modified parts can be grounds for disallowing a warranty claim. Poulan PRO is not liable to cover failures of warranted parts caused by the use of add- -on or modified parts.