Pfaff 333-712/02 Instruction Manual
Hide thumbs
Also See for 333-712/02:
- Instruction manual (72 pages) ,
- Adjustment manual (30 pages) ,
- Instruction manual (58 pages)
Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Instruction Manual
Advertisement
Table of Contents
Related Manuals for Pfaff 333-712/02
Summary of Contents for Pfaff 333-712/02
-
Page 1: Instruction Manual
-712/02 INSTRUCTION MANUAL This instruction manual applies to machines from the following serial numbers onwards: 7 262 019 and software version 0435/002. 296-12-19 288/002 Instruction Manual engl. 10.15... - Page 2 Internet download, the settings manual can also be ordered un- der order no. 296-12-19 289/002 . Reprinting, reproduction and/or translation of PFAFF instruction manuals (including parts thereof) is only permitted with our prior agreement and citation of the source.
-
Page 3: Table Of Contents
Danger warnings ........................8 Proper Use ..........................9 Technical Data ........................10 3.01 PFAFF 333-712/02 ........................ 10 Disposal of the Machine ....................11 Transport, Packaging and Storage ................... 12 Transport to the customer’s premises ................12 Transport within the customer’s premises ................12 Disposal of the packaging materials .................. - Page 4 Table of Contents Contents ..................Page Connecting the plug-in connections and ground cable ............20 Assembling the reel stand ....................21 Initial start-up ........................22 Switching the machine on / off .................... 22 Machine drive home position ....................22 Set-up ..........................23 Inserting the needle ......................
-
Page 5: Safety
Fitting or using these products may therefore have negative effects on features which depend on the machine design. We are not liable for any damage caused by the use of non-Pfaff parts. -
Page 6: Safety Symbols
Safety Safety symbols Hazard point! Special points of attention. Risk of injury to operating personnel or technical staff! Electric voltage! Danger to operating personnel or technical staff Caution! Do not operate without finger guard and safety covers! Turn off the main switch before threading, changing the bobbin or needle, cleaning, etc.! Special points of attention for the owner-operator ●... -
Page 7: Operating Personnel And Technical Staff
Safety Operating personnel and technical staff Operating personnel .05.01 Operating personnel are persons responsible for equipping, operating and cleaning the ma- chine and for fault clearance in the sewing area. The operating personnel are obligated to comply with the following points: ●... -
Page 8: Danger Warnings
Safety Danger warnings A work area of 1 m must be kept free in front of and behind the machine to en- sure unobstructed access at all times. Do not reach into the needle range during the sewing operation! Risk of injury from the needle! Do not allow any objects to be placed on the table during the adjustment work! The objects could become jammed or be slung away! Risk of injury from parts flying around! -
Page 9: Proper Use
Proper Use Proper Use The PFAFF 333-712/02 is a single needle lockstitch free arm sewing machine for industrial lockstitch darning work. Any usage not approved by the manufacturer is deemed misuse! The manufac- turer shall assume no liability for damage caused by misuse! Proper use also... -
Page 10: Technical Data
Technical Data Technical Data ▲ PFAFF 333-712/02 Stitch type: ......................301 ( lock stitch ) Needle system : ........................190 Design A: ...............for the machining of light-weight materials. Needle size in 1/100 mm: Model A: ......................... 60 - 80 Thread thickness max. -
Page 11: Disposal Of The Machine
Disposal of the Machine Disposal of the Machine ● It is up to the customer to dispose of the machine properly. ● The materials used for the machine include steel, aluminium, brass and various plastics. The electrical equipment consists of plastics and copper. ●... -
Page 12: Transport, Packaging And Storage
Transport, Packaging and Storage Transport, Packaging and Storage Transport to the customer’s premises All machines are completely packed for delivery. Transport within the customer’s premises The manufacturer assumes no liability for transport within the customer’s premises or to the individual usage sites. Please ensure that the machines are only transported in a vertical po- sition. -
Page 13: Work Symbols
Work Symbols Work Symbols Activities to be performed or important information in this instruction manual are empha- sised by symbols. The symbols used have the following meaning: Note, information Cleaning, care Lubrication Maintenance, repairs, adjustment, service work (only to be carried out by technical staff) -
Page 14: Operating Controls
Operating Controls Operating Controls Main switch Before switching on the ma- chine, raise the take-up lever as far as possible. ● Operating the main switch 1 switches the machine on and off. Fig. 7 - 01 Material presser foot stroke adjustment Switch off the machine! Risk of injury due to accidental machine start-up! -
Page 15: Treadle
Operating Controls Treadle ● With the main switch turned on = Resting position = Sewing = Trim thread and raise materi- al presser foot/(in machines with thread trimmer -900/51) Fig. 7 - 03 Control panel (only in machines with P40 CD) The description can be found in the instruction manual for the drive. -
Page 16: Set-Up And Initial Commissioning
Set-up and Initial Commissioning Set-up and Initial Commissioning The machine may only be set up and started up by qualified personnel! All of the relevant safety regulations must always be complied with in this process! If the machine was delivered without a table, then the stand and the table top provided must safely support the weight of the machine and its motor. -
Page 17: Mounting The Thread Retainers
Set-up and Initial Commissioning Mounting the thread retainers .01.02 ● Screw the thread retainers 1 and 2 into the tapped holes on the top of the ma- chine and secure them using the nuts 3 and 4. When mounting the thread re- tainers, make sure that the ❶... -
Page 18: Mounting The Fl Ange Motor On The Machine
Set-up and Initial Commissioning Mounting the flange motor on the machine .01.04 ● Use screws 3 to fix the bearing plate 1 of the motor 2 to the machine housing (slightly tighten the screws 3). ● Remove the wedge from the motor shaft 4. -
Page 19: Mounting The Synchroniser
Set-up and Initial Commissioning Mounting the synchroniser .01.06 ● Slide the synchroniser 1 onto the shaft so that the position finger 2 is positioned in the synchroniser groove (see arrow) ● Tighten the screws 3. ● Insert the synchroniser plug on the con- trol box (see Chapter 8.02 Connecting the plug-in connections and ground cable). -
Page 20: Connecting The Plug-In Connections And Ground Cable
Set-up and Initial Commissioning Connecting the plug-in connections and ground cable Fig. 8 - 07 ● Insert all plugs on the control box 2 in accordance with their designation. ● Insert the “motor” to the bushing E and the bushing M. Caution Inserting the plug incorrectly can damage the control unit! ●... -
Page 21: Assembling The Reel Stand
Set-up and Initial Commissioning Assembling the reel stand ● Assemble the reel stand as shown in the adjacent illustration. ● Then insert the stand into the hole in the table top and secure it with the enclosed nuts. Fig. 8 - 08... -
Page 22: Initial Start-Up
Set-up and Initial Commissioning Initial start-up ● Inspect the machine, particularly the electric cables, for any damage. ● Clean the machine thoroughly and then oil it, see also Chapter 10 Maintenance and Care. ● Arrange for technical staff to check whether the machine’s motor may be operated at the existing mains voltage and whether it is connected properly. -
Page 23: Set-Up
Set-up Set-up Observe and comply with all regulations and instructions in this instruction manual. Pay particular attention to all safety regulations! All set-up work may only be carried out by appropriately instructed personnel. Disconnect the machine from the electricity mains for all set-up work by operat- ing the main switch or by removing the mains plug! Inserting the needle Switch off the machine! -
Page 24: Winding The Bobbin Thread, Adjusting The Thread Tension
Set-up Winding the bobbin thread, adjusting the thread tension Fig. 9 - -02 ● Fit the empty bobbin 1 onto the bobbin winder spindle 2 with the rest thread chamber on the outside. ● Thread in the thread as shown in Fig. 9 - 02 and wind it round the bobbin 1 a few times in an anti-clockwise direction. -
Page 25: Removing / Inserting The Bobbin Case
Set-up Removing / inserting the bobbin case Switch off the machine! Risk of injury due to accidental machine start-up! Removing the bobbin case: ● Open the flap 1. ● Raise the lever 2 and remove the bob- bin case 3. Fig. -
Page 26: Inserting The Bobbin Case / Adjusting The Bobbin Thread Tension
Set-up Inserting the bobbin case / adjusting the bobbin thread tension ● Insert the bobbin as shown in Fig. 9-05. ● When the thread is drawn off, the bob- bin must turn in the direction shown by the arrows. ● Adjust the thread tension on the screw 1. Fig. -
Page 27: Threading The Needle Thread / Adjusting The Needle Thread Tension
Set-up Threading the needle thread / adjusting the needle thread tension Fig. 9 - 06 Switch off the machine! Risk of injury due to accidental machine start-up! ● Thread the needle thread as shown in Fig. 9-06. Please ensure that the needle is thread- ed from the left. -
Page 28: Setting The One-Point Sewing
Set-up Setting the one-point sewing ● Switch the machine on. ● Press the button to call up the sewing program. ● Set the stitch count by pressing the corresponding +/- button ● Press the button and set the speed. ● Set the speed by pressing the corresponding +/- button ●... -
Page 29: Maintenance And Care
Maintenance and Care Maintenance and Care Maintenance intervals Cleaning ............daily, several times if in continuous operation Clean the hook area ........daily, several times if in continuous operation General oiling ....................twice a week Oil the hook ..................daily, before start-up Oil the front parts ................... -
Page 30: General Oiling
● Oil all points marked with arrows twice a week. Only use oil with a centre viscosity of 22.0 mm /s at 40 °C and a density of 0.865 g/cm at 15 °C! We recommend PFAFF sewing machine oil, order no. 280-1-120 144. -
Page 31: Oiling The Hook
22.0 mm at 40 °C and a density of at 15 °C! 0.865 g/cm We recommend PFAFF sewing machine oil, order no. 280-1-120 144. Fig. 10 - 03 Oiling the front parts Switch off the machine! Risk of injury due to accidental machine start-up! ●... -
Page 32: Parameter Settings
Maintenance and Care Parameter settings Parameter settings are described in the separate parameter list for the drive and may only be changed by qualified technicians. -
Page 33: Table Top
Table top cutout Table Top Table top cutout... -
Page 34: Table Top Assembly
Table top assembly Table top assembly 102,5 102,5 Stecker / Steuerung / control box P40CD connector... -
Page 35: Wearing Parts
This list shows the most important wearing parts. A detailed parts list for the complete machine can be downloaded at www.pfaff-industrial.de/de/service-support/downloads/technical. As an alternative to the Internet download, the parts list can also be requested as a hard copy under order no. 296-12-19 288. - Page 36 Wearing Parts 99-137 151-45 91-171 049-05 91-171 042-05 95-774 464-25 91-700 996-15 91-060 461-91 91-000 713-15 (2x) 91-141 954-91 91-000 678-15 (4x) 91-009 076-61 91-175 690-05 91-009 026-05 91-000 250-15 91-000 390-05 91-002 134-05 91-168 144-15...
- Page 37 Notes...
- Page 38 PFAFF Industriesysteme und Maschinen GmbH Hans-Geiger-Str. 12 - IG Nord D-67661 Kaiserslautern Tel.: +49 - 6301 3205 - 0 Fax: +49 - 6301 3205 - 1386 E-mail: info@pfaff-industrial.com Gedruckt in der BRD / Printed in Germany / Imprimé en la R.F.A. / Impreso en la R.F.A...