Download
Share
Print this page
Alinco DJ-196 Instruction Manual
  1. Manuals
  2. Brands
  3. Alinco Manuals
  4. Two-Way Radio
  5. DJ-196
  6. Instruction manual
Alinco DJ-196 Instruction Manual

Alinco DJ-196 Instruction Manual

Hide thumbs Also See for DJ-196:

Advertisement

Quick Links

Download this manual See also: Instruction Manual
DJ196 INSTRUCTION MANUAL
1. INNOVATIVE AND NEW FEATURES
. Comes equipped 39 CTCSS Tone Squelch function.
. Comes equipped 104DCS Digital code squelch function.
. TOT(Time Out Timer) can be set to a Duty Cycle most accommodating to the user's
requirements.
. Alphanumeric channel name function.
. Tone burst function（1750,2100,1000,1450Hz）
. Nine Autodial memories easily accessed from the DTMF keypad with redial function.
. Direct frequency entry from DTMF function.
. Burglary Alarm Function
. Mosquito Repel sound function.
2. SPECIFICATIONS
  GENERAL
  Frequency coverage T: TX 144-147.995MHz  RX 135-173.995MHz
        
           
        
        
  Mode
  
  Channel steps  
  Memory channels 
Antenna connector
Frequency stability 
Microphone input impedance
Power supply requirement  6.0 - 16.0 V DC (negative ground)
  Current drain (at 13.8 V DC) 1.2 A(typical) Transmit high at 5W
        
        
Usable temperature range   -10 - +60 deg.
Dimensions  
   (Projections not included)
Weight            Approx.375ｇ（with EBP-48N）
DTMF  
Subaudible Tone(CTCSS) encoder/decoder installed(39tones)
Subaudible Tone (DCS) encoder/decoder installed(104codes)
 
TRANSMITTER
  Output power 
        
  Modulation system    Variable reactance frequency modulation
  Spurious emissions  
  Max.frequency deviation +/-5Hz
  
E: TX 144-145.995MHz  RX 144-145.995MHz
TA2: TX 150-173.995MHz  RX 135-173.995MHz
F3E (FM)
5,10,12.5,15,20,25,& 30kHz
40 channels＋1CALL channel
BNC(50ohm unbalanced）
+/-5 ppm
2Kohm nominal
200 mA(typical) Receive at 280mW
50 mA(typical) standby
56(Ｗ）＊124(H)＊ 40(D)mm (with EBP-48N)
16 Buttons Keypad
  Approx. 5 W EBP-48N installed
Approx. 5 W 13.8 V DC
Approx. 0.8 W (LOW)
Less than -60dB
                     

Advertisement

loading

Related Manuals for Alinco DJ-196

Summary of Contents for Alinco DJ-196

  • Page 1 DJ196 INSTRUCTION MANUAL                       1. INNOVATIVE AND NEW FEATURES . Comes equipped 39 CTCSS Tone Squelch function. . Comes equipped 104DCS Digital code squelch function. . TOT(Time Out Timer) can be set to a Duty Cycle most accommodating to the user’s requirements.
  • Page 2 RECEIVER   Receive system    Double conversion superheterodyne   Intermediate frequencies  1st 21.7MHz／ 2nd 450kHz   Sensitivity(12dB SINAD)  Less than –14.0 dBu(0.2uV) [144-147.995MHz]          Less than –12.0 dBu(0.25uV)[135-173.995MHz]   Selectivity    -6dB:12kHz or more   -60 dB:24kHz or less   Audio output power  280 mW (typical with an 8ohm load)             ...
  • Page 3 Operation Manual DJ196Contents 5 Operation 1(Basics) 5-1 Adjusting the Volume 5-2 Adjusting the Squelch 5-3 Receiving 5-4 Transmitting 5-5 Frequency Selection 5-6 Channel Step 5-7 Shift Direction and Offset Frequency 5-8 Memory Channel Operation 5-9 CALL Channel Operation 5-10 Scanning 5-11 Output Power Switching 5-12 Key Lock Function 5-13 Tone Burst Function...
  • Page 4 5 Operation 1 (Basics) 5-1 Adjusting the Volume . [VOL｣ appears on LCD when VOL key is pressed, volume level is displayed. The initial value is 00 (minimum). The volume can be increased or decreased by rotating the dial. The maximum value is 20.  There are 21 steps from 00-20 in volume adjustment.
  • Page 5 [Ｍ] or [Ｃ] is not displayed on the LCD in the VFO mode. [UP/DOWN with channel step] 1. Rotating the dial clockwise increases frequency 1 channel step/1 click, and rotating counterclockwise decreases the frequency 1 channel step/1 click. [1MHz UP/DOWN] 1.
  • Page 6 30kHz to either 12.5kHz or 25kHz, or changed in reverse, the frequency and shift width may be compensated. 5-7 Shift Direction and Offset Frequency Usually the repeater is used in the duplex mode. Namely the signal received with a certain frequency is transmitted with another frequency. The difference between these frequencies is the offset frequency.
  • Page 7 2. Rotate the dial to select the desired memory channel number. When the memory channel is programmed, [Ｍ] appears on the LCD. 3. Press and hold the FUNC key, then press MW key while [F] icon is ON. A beep sounds, and the programmed frequency will be erased.
  • Page 8 . The last direction of UP/DOWN is defined as the scan direction. (1) VFO SCAN 1. Press the V/M key to enter VFO mode. 2. Press the SCAN key to start scanning. The decimal point of the frequency on the LCD starts flashing to indicate the scanning is started.
  • Page 9 The initial value of the tone frequency is 1750Hz, and it is changeable in the set mode. When tone and DCS are set, the signal will be transmitted with tone frequency and DCS code. 5-14 Auto Power Off Function The function prevents the battery from consuming when you forget to turn off the power switch. (1) Setting Press and hold the F key, then press 6/APO key while F icon is ON.
  • Page 10 5-19 Clock Shift Function In the unlikely event that CPU clock noise is present on a particular operating frequency programmed into the radio, you can shift the CPU clock frequency to avoid the CPU clock noise, which normally is so weak that it is inaudible even if the radio is tuned exactly to its frequency.
  • Page 11 respectively to each memory CH. 【Changing both of tone encoder/tone decoder frequencies】 1. Set the tone encoder in the tone squelch setting mode. (T icon is ON.) Change the tone encoder frequency with dialing, then the setting is completed. 2. When memory is programmed in this mode, the current tone frequency will be programmed to both of encoder frequency and decoder frequency.
  • Page 12 1. Press and hold the F key, then press 9/ dial M key, the unit enters the dialer setting mode. 6 digits are displayed, and nothing appears at first. 2. Select the dialer memory NO. with the dial. 3. For example, when you input 1 2 3 4 5 6 7 8 9, the LCD displays as shown below: [ １] →...
  • Page 13 starts after the programmed WAIT time elapsed. The initial setting is 100ms. 【DTMF burst/Pause time】 1. When the DTMF code is transmitted using the auto dialer, the code is transmitted with programmed burst/ pause time. The initial setting is 60ms. 【DTMF first digit's burst time】...
  • Page 14 (When the TOT Penalty is set, transmission can not be done even if you turn OFF the PTT then ON again within the programmed time.) 6-12 TOT Penalty Function When the transmission is completed by the TOT function, the transmission will be inhibited within the programmed TOT Penalty time.

  • Page 15: Operation

    data is transferred to the other transceiver. 4. The transfer is completed, "PASS" appears on the LCD. 5. Turn the power OFF, and the Clone mode is released. If data transfer is failed, "PASS" does not appear on the LCD. Try again from the first. 7-2 Burglary Alarm Function If someone tries to steal your transceiver, an alarm goes off from the speaker.
  • Page 16 Here is the explanation of each function. [No.1] Battery Save Function ON/OFF 1. [BS-ON] appears on the LCD. 2. Rotate the dial, and the display toggles as shown below. Then ON and OFF are switched repeatedly. ..downward upward….. ……BS-ON → BS-OF ………. ………………………………….
  • Page 17 ….. Downward…….Upward………… ……. TP-0FF….. TP-1…… TP-4…… TP-15………. ………………………………………………………. The setting is available up to max. 15 seconds. [No.8] DTMF WAIT time 1. [DWT-01] appears on the LCD. 2. Rotate the dial, and the display toggles as shown below. Then the DTMF WAIT time will be changed.

  • Page 18: Reset Function

    2. Rotate the dial, and the display toggles as shown below. The ON/OFF of the Mosquito repel sound will be switched repeatedly. …… Downward…….Upward………….. …………MRS-OF …..MRS-ON……….. …………………………………………… ９ RESET Function Press and hold the F key, then turn on the power. The unit returns to the factory's default setting. …………………………………………………………………………………………………..