Shure 526T Series II Wiring Manual page 16
Cb and amateur radio
Hide thumbs
Also See for 526T Series II:
- Datasheet (4 pages) ,
- Instruction manual (2 pages) ,
- Wiring manual (37 pages)
Advertisement
SBE
Land Command
LCM-8
26CB/A, 45CB,
42CB, 44C8 (Malibi
40), 54CB
Land Command
LCM-5
Land Command
LCM-8P
1CB (Coronado)
lOCB (Coronado II),
1 l C B (Trinidad).
SEARS
1, 2
934-38260701
934-38310700
2, 3, 5, 7
663-38070700;
934-38080700,
-381 10700,
1,2
-381 20700,
-38081700,
8
-38060700,
-38062700,
-38310700
2
934-38260700
934-38160700;
#4
#2
#2
AUDlO
#2
WHITE
(white)
#2
#1
#1
GND
#3
BLACK
526T Series II
Model
(others)
#5
#4
#3
RELAY
#4
SHIELD
(shield)
Notes
526T Series II
Model
(others)
YELLOW
(black)
#2
#3
#1
GND
#3
WHITE
(white)
12CB (Sidebander
1 1 )
6CB
7CB (Sierra)
8CB (Console),
16CB (Console !I)
9CB (Catalina)
14CB (Super Console)
21CB (Cortez),
18CB (Side-
bander Ill),
26CB (Formula D),
29CB (Catalinal
Malibu)
22CB (Cataiina II)
23CB (Capri II)
32CB, 34CB (Brute)
26CB, 30CB
31CB (Shasta I),
24CB (Shasta Ill)
39CB (Sidebander
V), 40CB (Console
V)
41CB (Aspen)
43CB, 47CB
(Stowaway)
49CB (Tahoe 40)
YELLOW
(black)
RED
(red)
SHIELD
(shield)
#1
AUDlO
AUDlO
AUDlO
# I
WHT
#4
#2
AUDlO
BLUE
#4
CKT GND
CKT GND
CHAS GND
#2
BLK
#1
# l
CKT GND
RED
(red)
#3
#3
#1
+
12v
$4
#3
CKT GND
RED
BRN
#4
# I
#3
#2
CKTGND
LSGND
I
CKTGND
I
NC
CHAS GND
LS GND
BLUE
XMTR CKT
XMTR CKT
XMTR CKT
#4
RED
#2
#1
#2
AUDlO
#2
#2
AUDlO
WHT
WHT
#2
#2
#2
i
BLACK
#3
#2
#1
GND
#4
# I
CKT GND
SHLD
SHLD
#1
#1
#1
#2
Notes
#2
NC
CKTGND
BLK
# I
#5
#1
NC
CKT GND
NC
,
XMTR CKT
SHAKESPEARE
GBS1500, GBS2500
GBS2000
GBS240
#2
#3
SHARP
CB-800, -2260
CB-2460
CB-2170, -4370
CB-4470, -4670
CBT-58
CB-5OOUB
CB-700
CB-750A, CB800A
#4
#3
#4
CHAS GND
GND
#4
#3
#4
#2
SLEEVE
#2
XMTR CKT
XMTR-VIO
SlLTRONiX
SSB-23
SSB-23A
101 18, C, D
RING
SLEEVE
NC
AM-1, AM-2
NC
(ApachelMohawk)
#2
#3
TIP
#4
M.H. SCOTT
Daks Mark IX
SEARS
370-38050700
562-38200700;
934-36771 500,
-36772600
934-38270700
663-38000900,
-38020800
NOTES
1. When using the 526T oniy (not the Series II) with this transceiver, cut the internal GRAY lead of the microphone.
2.
When using the 526T oniy (not the Series II) with this trans:?iver, cut the internal WHITE lead of the microphone from the
amDlifier to the ~ress-to-talk switch (see Fiaure 4).
ABBREVIATIONS
3. when using the'526T only (not the ~eries'il) wiih this transceiver, cut the internal BLUE lead. Refer to the Isolated
Switching section of the data sheet.
4. This transceiver requires a high-impedance audio input. When using the CB41, CB42, CB43, CB44, and CB45, the GREEN
audio lead replaces the WHITE audio lead.
5. This transceiver requires an isolated switching contact when using the CB41, C842, CB43, CB44, and CB45. Refer to the
Isolated Switching section of the data sheet for circuit modification instructions (see Figure 3).
6. This transceiver is recommended for use only with the 526T Series II.
7. When using the 526T Series II with this transceiver, the YELLOW lead is not used.
8. This transceiver is not recommended for use with Shure Citizens Band microphones.
9.
This transceiver is recommended for use only with the 526T Series II after special internal modifications are made. Refer
to the data sheet, or write to Shure Brothers Incorporated.
SW
=
switch
V
=
volt
VIO
=
violet
WHT
=
white
XMTR
=
transmittel
YEL
=
yellow
Z
=
impedance
BLK
=
black
BLU
=
blue
BRN
=
brown
CHAS
=
chassis
CKT
=
circuit
CTR
=
center
GND
=
ground
GRN
=
green
HI
=
high
LO
=
low
LS
=
loudspeaker
MIC
=
microphone
NC
=
no connection
ORN
=
orange
PWR SPLY
=
power supply
RCVR
=
receiver
Rev
=
revised
SHLD
=
shield
Advertisement
