Electrical Safety Warning - Poulan Pro 115259826 Instruction Manual

S Keep the handles dry and clean and
free from oil and grease.
S Keep oil cap and fasteners securely
tightened.
S Nonconforming replacement compo-
nents or the removal of safety devices
may cause damage to the unit and pos-
sible injury to the operator or bystand-
ers. Use only Poulan accessories and
replacement parts as recommended.
Never modify your saw.
S Maintain chain saw with care.
S Keep unit sharp and clean for better
and safer performance.
S Follow instructions for lubricating and
changing accessories.
S Unplug the chain saw from the power
source when not in use, before servic-
ing, and when changing accessories
and attachments, such as saw chain
and guard.
S Check for damaged parts. Before fur-
ther use of the chain saw, a guard or
other part that is damaged should be
carefully checked to determine that it will
operate properly and perform its in-
tended function. Check for alignment of
moving parts, binding of moving parts,
breakage of parts, mounting and any
other conditions that may affect its op-
eration. A guard or other part that is
damaged should be properly repaired
or replaced by an authorized service
dealer unless otherwise indicated else-
where in the instruction manual.
S When not in use, chain saws should
be stored in a dry, high or locked-up
place out of the reach of children.
S When storing saw, unplug and use a
bar sheath or carrying case.
ELECTRICAL SAFETY
WARNING:
Avoid a dangerous
environment. To reduce the risk of elec-
trical shock, do not use in rain, in damp
or wet locations, or around swimming
pools, hot tubs, etc. Do not expose to
snow, rain, or water to avoid the possibil-
ity of electrical shock. Do not handle ex-
tension cord or plug with wet hands.
S Use a voltage supply as shown on the
nameplate of the unit.
S Avoid dangerous situations. Do not
use in the presence of flammable liq-
uids or gases to avoid creating a fire or
explosion and/or causing damage to
unit.
S To reduce the risk of electrical shock,
this appliance has a polarized plug (one
blade is wider than the other) and will re-
quire the use of a polarized extension
cord. The appliance plug will fit into a po-
larized extension cord only one way. If
the plug does not fit fully into the exten-
sion cord, reverse the plug. If the plug
still does not fit, obtain a correct polar-
ized extension cord. A polarized exten-
sion cord will require the use of a polar-
ized wall outlet. This plug will fit into the
polarized wall outlet only one way. If
plug does not fit fully into the wall outlet,
reverse the plug. If the plug still does not
fit, contact a qualified electrician to install
the proper wall outlet. Do not change the
equipment plug, extension cord recep-
tacle, or extension cord plug in any way.
S To reduce risk of electrical shock, use
extension cords specifically marked as
suitable for outdoor appliances. The
electrical rating of the cord must not be
less than the rating of unit. The cord
must be marked with suffix "W- -A" (in
Canada, "W"). Use a polarized cord.
Make sure your extension cord is in
good condition. Inspect extension cord
before use and replace if damaged. Do
not use a damaged cord. Cord insula-
tion must be intact with no cracks or de-
terioration. Plug connectors must be
undamaged. An undersized extension
cord will cause a drop in line voltage re-
sulting in loss of power and overheating.
If in doubt, use the next heavier gauge.
The lower the gauge number, the heavi-
er the cord (see
SELECT AN EXTENSION
in the
CORD OPERATION
not use multiple cords.
S Do not abuse cord. Never carry the
unit by the extension cord or yank ex-
tension cord to disconnect unit.
S Secure extension cord to power cord
to prevent disconnection from unit.
S Do not use the unit if the switch does
not turn the unit on and off properly, or
if the lockout does not work. Repairs to
the switch must be made by an autho-
rized service dealer.
S Keep extension cord clear of operator
and obstacles at all times. Position
cord so that it will not be caught on
branches. Do not expose cords to
heat, oil, water, or sharp edges.
S To avoid the possibility of electric
shock, avoid body contact with any
grounded conductor, such as metal
fences or pipes.
S Ground Fault Circuit Interrupter (GFCI)
protection should be provided on circuit
or outlet to be used. Receptacles are
available having built-in GFCI protection
and may be used for this measure of
safety. Inspect chain saw cords periodi-
cally and if damaged, have repaired by
an authorized service dealer.
3
section). Do