SERVICING NOTICES ON CHECKING 1. KEEP THE NOTICES 3. PUT PARTS AND WIRES IN THE ORIGINAL POSITION AFTER As for the places which need special attentions, ASSEMBLING OR WIRING they are indicated with the labels or seals on the cabinet, chassis and parts. Make sure to keep the There are parts which use the insulation indications and notices in the operation manual.
GENERAL SPECIFICATIONS G-1. Outline of the Product -Speed 1/2" Video Cassette Recorder G-2. VCR Format VHS Standard NTSC SECAM PAL-M PAL-N VHS Hi-Fi Audio System G-3. Video Recording System : Rotary,slant azimuth two head helical scan system Luminance Component : FM recording Chrominance Component: Low frequency converted direct recording G-4.
Page 4
GENERAL SPECIFICATIONS G-17.Tuner and Receiving Channel Tuner: Contactless Electric Tuner Oscar(W/O HYPER) Oscar(W/ HYPER) France CATV Others Channel coverage 2 ~ 69 , 4A , A-5 ~ A-1 , A ~ I , J ~ W , W+1 ~ W+84 Tuning System Frequency syn.
Page 5
GENERAL SPECIFICATIONS G-26.Power Source AC 50Hz AC 60Hz G-27.Power Consumption: W at AC Hz(Approx.) Stand by: W at AC Hz(Approx.) Per Year: kWh / Year G-28.Dimensions(Approx.) 360 mm(W) 232.5 mm(D) mm(H) G-29.Weight(Approx.) Kg ( 7.1 lbs) Gross Kg ( 8.4 lbs) G-30.Cabinet Material Cabinet Front: 94HB...
Page 6
GENERAL SPECIFICATIONS G-39.Terminals VHF/UHF Antenna Input/Output Din Type F-Type France Type Front Video Input<RCA ø8.3> Front Audio Input<RCA ø8.3> x2 Rear Video Input<RCA ø8.3> Rear Audio Input<RCA ø8.3> Rear Video Output<RCA ø8.3> Rear Audio Output<RCA ø8.3> x2 21 Pin G-40.Indicator Power Play Repeat...
Page 7
GENERAL SPECIFICATIONS G-43.Carton Master Carton: Need No Need Content: ---- Material: ---- ---- Corrugated Carton Dimensions: ---- mm(W) ---- mm(D) ---- mm(H) Description of Origin Gift Box Need No Need Material Single/Brown Corrugated Carton ( with Photo Label) Single/White Corrugated Carton ( with Photo Label) Single Full Color Carton W/Photo Dimensions:...
Page 8
GENERAL SPECIFICATIONS G-47.Remote Control Unit :RC-DP Glow in Dark Remocon Power Source: D.C V Battery UM - 4 x 2 Control Key :Total Ch Up Power Ch Down Eject Input Select Play Audio Select Stop TV/VCR F.FWD Pause/Still Slow Timer Rec Speed REC/OTR Counter Reset...
DISASSEMBLY INSTRUCTIONS 1. REMOVAL OF MECHANICAL PARTS 1-3: DECK CHASSIS (Refer to Fig. 1-3) Remove the 3 screws 1. AND P.C. BOARDS Remove the screw 2. 1-1: TOP CABINET, FRONT CABINET AND Disconnect the following connectors: (CP1001, CP1002, OPERATION PCB (Refer to Fig. 1-1) CP1003, CP4001, CP4002 and CP4003).
DISASSEMBLY INSTRUCTIONS 2. REMOVAL OF DECK PARTS NOTE When you install the Tape Guide L, install as shown in the 2-1: TOP BRACKET (Refer to Fig. 2-1) circle of Fig. 2-3-B. (Refer to Fig. 2-3-B) Remove the 2 screws 1. Slide the 2 supports 2 and remove the Top Bracket.
Page 11
DISASSEMBLY INSTRUCTIONS 2-6: LINK ASS'Y (Refer to Fig. 2-6) Tension Adjust Set the Link Ass'y to the Eject position. Remove the (A) side of the Link Ass'y first, then remove Tension Band Ass'y the (B) side. Tension Spring Tension Arm Ass'y Tension Holder Link Ass'y SS Brake Spring...
Page 12
DISASSEMBLY INSTRUCTIONS 2-10: S REEL/T REEL (Refer to Fig. 2-10) NOTE Remove the S Reel and T Reel. Do not touch the Pinch Roller. (Use gloves.) Remove the 2 Polyslider Washers 1. When you install the Pinch Roller Block, install as shown in the circle of Fig.
Page 13
DISASSEMBLY INSTRUCTIONS 2-14: AHC ASS'Y/CYLINDER UNIT ASS'Y (Refer to Fig. 2-14) Middle Gear Unlock the support 1 and remove the AHC Ass'y. E-Ring Remove the 3 screws 2. Remove the Cylinder Unit Ass'y. Main Cam NOTE Pinch Roller Cam When you install the Cylinder Unit Ass'y, tighten the screws from (1) to (3) in order while pulling the Ass'y Joint Gear toward the left front direction.
Page 14
DISASSEMBLY INSTRUCTIONS 2-18: LOADING GEAR S/T ASS'Y (Refer to Fig. 2-18-A) 2. When you install the Clutch Actuator, install as shown in the circle of Fig. 2-18-C. (Refer to Fig. 2-18-C) Remove the E-Ring 1 and remove the Main Loading Gear.
KEY TO ABBREVIATIONS Audio/Control H.SW Head Switch Automatic Color Control Hertz Audio Erase Integrated Circuit Automatic Frequency Control Intermediate Frequency Automatic Fine Tuning Indicator AFT DET Automatic Fine Tuning Detect Inverter Automatic Gain Control Killer Amplifier Left Antenna Light Emitting Diode A.PB Audio Playback LIMIT AMP...
Page 16
KEY TO ABBREVIATIONS SYNC Synchronization SYNC SEP Sync Separator, Separation Transistor TRAC Tracking TRICK PB Trick Playback Test Point UNREG Unregulated Volt Voltage Controlled Oscillator Video Intermediate Frequency Vertical Pulse, Voltage Display V.PB Video Playback Variable Resistor V.REC Video Recording Visual Search Fast Forward Visual Search Rewind Voltage Super Source...
SERVICE MODE LIST This unit provided with the following SERVICE MODES so you can repair, examine and adjust easily. Method Operations Press both PLAY button and Initialization of the factory. CH UP button on the set for NOTE: Do not use this for the normal servicing. more than 2 seconds.
PREVENTIVE CHECKS AND SERVICE INTERVALS The following standard table depends on environmental conditions and usage. Unless maintenance is properly carried out, the following service intervals may be quite shortened as harmful effects may be had on other parts. Also, long term storage or misuse may cause transformation and aging of rubber parts. Time 1,000 1,500...
PREVENTIVE CHECKS AND SERVICE INTERVALS CLEANING NOTE 2. TAPE RUNNING SYSTEM After cleaning the heads with isopropyl alcohol, do not When cleaning the tape transport system, use the run a tape until the heads dry completely. If the heads gauze moistened with isopropyl alcohol. are not completely dry and alcohol gets on the tape, 3.
NOTE FOR THE REPLACING OF MEMORY IC If a service repair is undertaken where it has been required to change the MEMORY IC, the following steps should be taken to ensure correct data settings while making reference to TABLE 1. Table 1 Turn on the POWER.
MECHANICAL ADJUSTMENTS 1. CONFIRMATION AND ADJUSTMENT 1-2: CONFIRMATION AND ADJUSTMENT OF TENSION POST POSITION Read the following NOTES before starting work. Set to the PLAY mode. • Place an object which weighs between 450g~500g on Adjust the Tension Adjust until the edge of the Tension the Cassette Tape to keep it steady when you want to Arm is positioning within 0.5mm range from the make the tape run without the Cassette Holder.
MECHANICAL ADJUSTMENTS 1-4: CONFIRMATION OF VSR TORQUE 2. CONFIRMATION AND ADJUSTMENT OF TAPE RUNNING MECHANISM Operate within 4~5 seconds after the reel disk begins to turn. Tape Running Mechanism is adjusted precisely at the Install the Torque Gauge (JG002F) and Adapter (JG002B) factory.
Page 24
MECHANICAL ADJUSTMENTS 2-2: CONFIRMATION AND ADJUSTMENT OF AUDIO/ 2-3: TAPE RUNNING ADJUSTMENT CONTROL HEAD (X VALUE ADJUSTMENT) When the Tape Running Mechanism does not work well, Confirm and adjust the height of the Reel Disk. adjust the following items. (Refer to item 1-1) Confirm and adjust the position of the Tension Post.
MECHANICAL ADJUSTMENTS 3. MECHANISM ADJUSTMENT PARTS LOCATION GUIDE 1. Tension Adjust X value adjustment driver hole 2. Tension Arm P4 Post 3. Guide Roller T Brake Spring 4. P1 Post T Reel 5. Audio/Control Head S Reel...
ELECTRICAL ADJUSTMENTS Read and perform this adjustment when repairing the circuits or replacing electrical parts or PCB assemblies. 1. BASIC ADJUSTMENT CAUTION When replacing IC's or transistors, use only specified silicon grease. (To prevent the damage to IC's and transistors.) 1-1: PG SHIFTER CONDITIONS MODE-PLAYBACK...
OPERATION SCHEMATIC DIAGRAM (OPERATION PCB) REW/REV SW607_2 SKQNAED010 PLAY SW606_2 SKQNAED010 FF/CUE SW605_2 SKQNAED010 REC/OTR SW604_2 SKQNAED010 STOP/EJECT SW603_2 SKQNAED010 CH-DOWN SW602_2 SKQNAED010 POWER SW608_2 SKQNAED010 CH UP SW601_2 TO DISPLAY SKQNAED010 CP601 IMSA-9604S-04Z13 KEY-A KEY-B PCB270 VE8859 NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE...
DECK SCHEMATIC DIAGRAM LOADING MOTOR M101 (DECK PCB) S105 BOT SENSOR S106 Q101 RPT-38PB113 S101 S102 S103 S104 FROM/TO MICON CP101 (CP1003) 52044-0445 LDM+ LDM- PCB550 VE8851 NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME NOTE: THE DC VOLTAGE AT EACH PART WAS CAUTION: SINCE THESE PARTS MARKED BY ATTENTION:...
INTERCONNECTION DIAGRAM HALL MAIN ROTOR SENSOR COIL MAGNET FG SENSOR HALL HALL SWITCH LOGIC CP1002 MOTOR GND I LIMIT VCO(12V) CAP FG 0R614902 CAP.M F/R VCC(5V) CAPSTAN DD UNIT WHITE M2001 BLACK CD501 CP501 AC120V_60Hz HEAD AUDIO CONTROL ASS’Y H5001 CD1002 CP4002 AUDIO PB...
CHASSIS EXPLODED VIEW (TOP VIEW) M2003 UN4001 H5001 H5002 M101 PCB550 (DECK PCB ASS'Y) NOTE: Applying positions AA and BA for the grease or CLASS MARK oil are displayed for this section. GREASE Check if the correct grease or oil is applied for each position.
CHASSIS EXPLODED VIEW (BOTTOM VIEW) M2001 NOTE: Applying positions AA and BA for the grease or CLASS MARK oil are displayed for this section. GREASE Check if the correct grease or oil is applied for each position.