Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Planet Networking & Communication MH-5000
Summary of Contents for Planet Networking & Communication MH-5000
- Page 1 Multi-Homing Security Gateway MH-5000 Quick Installation Guide...
-
Page 2: Before You Begin
Before You Begin It’s best to use a computer with an Ethernet adapter for configuring the MH-5000. The default IP address for the MH-5000 is 192.168.1.254 (LAN1 at the port number 4) with a Subnet Mask of 255.255.255.0. You will need to assign your computer a Static IP address within the same range as the MH-5000’s IP address, say... -
Page 3: System Architecture
System Architecture MH-5000 is an integrated solution that can provide enterprises the maximum security and the best resource utilization. It contains stateful inspection Firewall, NAT, VPN, Intrusion Detection System, Dynamic Routing, Content Filtering, Bandwidth Management, WAN load balancer, Anti-Virus and Anti-Spam in a single box. - Page 4 The Power LED will turn ON to indicate proper operation. Using an Ethernet cable, insert one end of the cable to the WAN port on the front panel of the MH-5000 and the other end of the cable to a DSL / Cable modem or other internet access devices.
-
Page 5: Using The Setup Wizard
A computer on your LAN1 must be assigned an IP address and subnet mask from the same range as the IP address and subnet mask assigned to the MH-5000, in order to be able to make an HTTPS connection using a web browser. The MH-5000 is assigned an IP address of 192.168.1.254 with a subnet mask of 255.255.255.0 by... - Page 6 BASIC SETUP > Wizard Step 3 － System Name Enter the Host Name and the Domain Name, followed by clicking the Next. BASIC SETUP > Wizard > Next Step 4 － WAN Connectivity To setup the first WAN link, make WAN1 as the Default WAN link.
- Page 7 BASIC SETUP > Wizard > Next > Fixed IP Step 4.b — Fixed IP If Fixed IP Address is selected, enter the ISP-given IP Address, Subnet Mask, Gateway IP, Primary DNS and Secondary DNS IP. Click Next to proceed. BASIC SETUP > Wizard > Next > PPPoE Step 4.c —...
- Page 8 BASIC SETUP > Wizard > Next > Next Step 5 － System Status Here we select Fixed IP method in WAN1 port. Then the MH-5000 provides a short summary of the system. Please check if anything mentioned above is properly set into the system.
-
Page 9: Basic Setup
‘applied’ before going on to the next page. WAN Settings The WAN Settings page allows you to modify the protocol that the MH-5000 will use to connect to your ISP and obtain the necessary network address information. - Page 10 2. Fixed IP Address If your ISP has assigned you an IP address that will never change, choose this option. When this option is chosen, the following fields appear to allow you to enter the network address information. The example shows that the ISP assigns an IP 61.2.1.1, a netmask 255.255.255.248, a default gateway 61.2.1.6, and DNS (168.95.1.1).
- Page 11 IP Address FIELD DESCRIPTION Assignment Default WAN When Default WAN link is enabled. link All the packets sent out from MH-5000 (Gateway/DNS) will be via this port. Get DNS Automatically à Get DNS Get DNS related information from DHCP Server Automaticaslly Get IP DNS IP Address à...
- Page 12 PPPoE line To simplify the initial settings of the MH-5000, the Network Address Translation is automatically configured if the NAT Basic mode is selected. Then the MH- 5000 will let all private-IP traffic from the subnets of LAN/DMZ ports to access...
-
Page 13: Lan Settings
The LAN Settings page allows you to modify the IP address and subnet mask that will identify the MH-5000 on your LAN. This is the IP address you will enter in the URL field of your web browser to connect to the MH-5000. It is also the IP address that all of the computers and devices on your LAN will use as their Default Gateway. - Page 14 FIELD DESCRIPTION Range / Limitation IP Address LAN port IP address IPv4 format IP Subnet LAN port IP subnet mask netmask format Mask Enable DHCP Enable LAN port of the Enable/Disable Server DHCP Sever or not IP Pool Specify the starting address IPv4 format in the LAN Starting of the DHCP IP address.
-
Page 15: Dmz Settings
IP address range) specified on the DHCP Servers. The DHCP Server fields allow you to configure the MH-5000 to be a DHCP Server on your DMZ. The MH-5000 can then automatically assign IP addresses, subnet masks, default gateway and DNS server addresses to computers on your DMZ. - Page 16 FIELD DESCRIPTION Range / Limitation IP Address DMZ port IP address IPv4 format IP Subnet DMZ port IP subnet mask netmask format Mask Enable DHCP Enable DMZ port of the Enable/Disable Server DHCP Sever or not IP Pool Specify the starting address IPv4 format in the DMZ Starting of the DHCP IP address.
-
Page 17: Virtual Server Settings
As the above Figure 2 illustrated, the server 10.1.1.5 provides FTP service and is located on the DMZ region behind MH-5000. By this way, MH-5000 will act as a Virtual Server role which redirects the packets to the real server 10.1.1.5. And you can announce to the internet users that the ftp server ip/port is 61.2.1.1/44444. - Page 18 Dest Port The port number in the internet. If the Passive FTP client is checked, it will Passive FTP connect to the internal DMZ FTP server of client? MH-5000 when FTP client uses passive mode. Otherwise, it will not work.
- Page 19 Redirect to The subnet which is located the virtual internal server server. under The IP address which is actually transferred Translated dest IP to the internal DMZ Translated dest The port number which is actually port transferred to the internal DMZ. Action Auto update to If you checked this, it will add a Firewall...