Technicolor TD5130 User Manual
  1. Manuals
  2. Brands
  3. Technicolor Manuals
  4. Gateway
  5. TD5130
  6. User manual

Technicolor TD5130 User Manual

Wireless adsl2+ gateway
Hide thumbs Also See for TD5130:
Table of Contents

Advertisement

Quick Links

See also: Setup and User's Manual

Advertisement

Table of Contents
loading

Related Manuals for Technicolor TD5130

Summary of Contents for Technicolor TD5130

  • Page 2: Table Of Contents

    Table of Contents Chapter 1: Product Overview ..................6 1.1 Features ......................... 6 1.2 Package Contents....................7 1.3 Hardware Overview ....................8 1.3.1 Front Panel ................... 8 1.3.2 Rear Panel................... 10 Chapter 2: Installation ....................11 2.1 Connect the Power....................11 2.2 Connect Wired Devices ..................
  • Page 3 5.3.2 DHCP Setting ..................36 5.3.3 DHCP Reserved Address ..............38 5.4 Time and Date ..................... 39 Chapter 6: Advanced ....................41 6.1 6.1 Advanced Wireless ..................41 6.1.1 Wireless Router Settings ..............41 6.1.2 MBSSID Settings ................. 43 6.1.3 Wireless MAC Filter ................43 6.1.4 WPS Setting ..................
  • Page 4 6.9.4 DOS Protection ................... 64 6.9.5 Domain Blocking ................65 6.9.6 DMZ..................... 65 6.9.7 SPI Settings ..................66 6.10 Packet Filter ......................67 6.10.1 Filters & Rules ................... 67 6.10.2 Statistics .................... 69 6.11 Static Route ......................69 6.12 Multicast ......................70 6.12.1 IGMP....................
  • Page 5 Chapter 8: Status......................95 8.1 Summary......................95 8.2 IPv6 Info....................... 95 8.3 ADSL Info......................96 8.4 Wireless Clients....................97 8.5 LAN Clients ......................97 8.6 Logs........................98 8.7 Routing Table ...................... 98 8.8 Traffic Meter ....................... 99 8.9 Driver Version....................100 8.10 Statistics ......................

  • Page 6: Chapter 1: Product Overview

    Product Overview Chapter 1: Product Overview ® Thank you for choosing Technicolor Wireless ADSL2+ Gateway. This Wireless Gateway combines the functionality of an ADSL modem and Internet gateway in one. You can access the Internet and share resources such as printers, scanners, and files, via a wireless connection or through one of the Ethernet ports.

  • Page 7: Package Contents

    Product Overview Package Contents Check if the package contains the following items. If any item is missing or appears damaged, contact your dealer. Wireless Gateway Power adapter CD-ROM with User’s Guide RJ-45 Ethernet cable RJ-11 telephone cable Wireless ADSL2+ Gateway...

  • Page 8: Hardware Overview

    Product Overview Hardware Overview 1.3.1 Front Panel 1 2 3 4 5 6 Description Lights up when the device is powered on. • Solid GREEN – Indicates normal operation. Power LED • Flashing GREEN – Firmware upgrade in progress. • Solid RED –...
  • Page 9 Product Overview Description Lights up to indicate the Wi-Fi Protected Setup (WPS) connection status. • Solid GREEN – WPS-enabled device is connected. WPS LED • Flashing GREEN – Data transmission is in progress. • Flashing RED – WPS connection failed. •...

  • Page 10: Rear Panel

    Product Overview 1.3.2 Rear Panel 1 2 3 5 6 7 Ports / Buttons Description DSL port Connects to the DSL line using the RJ-11 cable. Press and hold this button for at least 10 seconds to restore Reset button your device to its original factory default setting.

  • Page 11: Chapter 2: Installation

    Installation Chapter 2: Installation Make sure that all devices are powered off before starting installation. Installation Diagram Connect the Power 1. Connect the power adapter to the DC In jack of your Wireless Gateway. 2. Plug the power adapter to a wall outlet or a power strip. NOTE: •...

  • Page 12: Connect Wired Devices

    Installation Connect Wired Devices Connect devices such as computers, printers, and other Ethernet-enabled devices to the LAN port of the Wireless Gateway. NOTE: When setting up the Wireless Gateway for the first time, connect the host computer via Ethernet connection. 1.

  • Page 13: Connect The Broadband (Dsl)

    Installation Connect the Broadband (DSL) 1. Connect one end of the RJ-11 cable to the DSL port of your Wireless Gateway. 2. Connect the other end of the RJ-11 cable to a wall jack with DSL service. 2.4.1 Use a Splitter You need a splitter when connecting the Wireless Gateway to the wall jack that also connects to a telephone.

  • Page 14: Chapter 3: Configure The Computer

    Configure the Computer Chapter 3: Configure the Computer This chapter will guide you on how to configure your computer according to the operating system you are using. ® Windows XP, see below. ® Windows Vista, see page 16. ® Windows 7, see page 16.

  • Page 15: Windows Vista

    Configure the Computer Windows Vista ® If you are using Windows Vista, follow the instructions below to configure your computer. 1. Click Start > Control Panel > Network and Internet Connections > Network Connections. 2. Right-click Local Area Connection, then click Properties.

  • Page 16: Chapter 4: Access The Wireless Gateway

    Log In to the Modem Router Chapter 4: Access the Wireless Gateway Use the Web Configurations utility to configure your Wireless Gateway. 1. Launch the web browser. 2. On the address bar, enter http://192.168.1.1, then press Enter. NOTE: • For first time access, the Setup Wizard appears. See below. •...
  • Page 17 Log In to the Modem Router 2. Select a network protocol. Click Next to continue. The information required on the succeeding pages varies depending on the network protocol you select here. 3. Select a scanning method, and then click Next to continue. •...
  • Page 18 Log In to the Modem Router a. Enter desired Profile Name. b. Enter the Virtual Path Identifier (VPI) and Virtual Channel Identifier (VCI). c. Select an Encapsulation mode: LLC, VCMUX. d. Select the ATMQoS option. e. Enter a Peak Cell Rate. f.
  • Page 19 Log In to the Modem Router 6. Select whether to enable or disable wireless connection. From this point, you can also change the SSID with a name that you can easily remember. Click Next to continue. 7. Select the Security Mode, Authentication Type, and Encryption, and enter a passphrase.

  • Page 20: Menu

    Log In to the Modem Router 9. To reboot the Wireless Gateway, click Reboot. Menu Use the main menu, located on the left panel of the screen, to manually configure your Wireless Gateway. Click a menu item, then a submenu to display the page on the screen.

  • Page 21: Chapter 5: Setup

    Setup Chapter 5: Setup The Setup menu allows you to configure the Internet connection of your Wireless Gateway manually. Internet Setup The Internet Setup page is divided into three sections: Internet Connection Settings, Internet Settings, and Protocol. To access the Internet Setup page, click SETUP >...

  • Page 22: Internet Settings

    Setup Enable Default Vlan — Select whether to enable or disable VLAN tagging. PPPoE PassThrough — Select whether to enable or disable PPPoE passthrough. 5.1.2 Internet Settings DSL lines use different network protocols to establish Internet connection. Ask your ISP and select the protocol used by your DSL line, options are: •...
  • Page 23 Setup State of Connection — Select whether to enable or disable this connection. IP Protocol Version — Select the type of IP protocol to use with this connection: • IPv4 only: Select to use IPv4 protocol. • IPv4/v6 both: Select to use this connection in both IPv4 and IPv6 protocols. •...
  • Page 24 Setup LCP Interval — Enter the number of seconds that you want to be the interval in sending LCP (Link Control Protocol) packets. As system default route — Check this box to set the current setting as the default route. ICMP Reply Enable —...
  • Page 25 Setup IPMode of Connection — Select the connection mode, options are: Dynamic: Select Dynamic if the IP address can be automatically obtained • from your ISP. • Static: Select Static if you are required to use a permanent IP address to connect to the Internet.
  • Page 26 Setup NOTE: If the IPv6 protocol is selected, the web utility may prompt for you to configure the IPv6 connection settings. See “IPv6 WAN” on page 48. IPoA (RFC-1483 Routed) If you select IPoA (IP over ATM), the screen below is displayed. State of Connection —...
  • Page 27 Setup ICMP Reply Enable — Check this box to enable ICMP (Internet Control Message Protocol) messages to be sent back to the host that sent the message. Proxy ARP Enable — Check this box to enable proxy ARP function. Click the Apply button to save your changes or click the Cancel button to discard your changes.
  • Page 28 Setup DNS Server 1 and DNS Server 2 — If provided by your ISP, enter the DNS server. Otherwise, leave these fields blank. MAC Address — Displays the cloned MAC address. Click the Clone Mac button to clone the MAC address of your computer. Option 125 —...

  • Page 29: Bridge Mode

    Setup • IPv4/v6 both: Select to use this connection in both IPv4 and IPv6 protocols. IPv6 only: Select to use IPv6 protocol. • Name — Enter your desired connection name. NAT — Select whether to enable or disable NAT (Network Address Translation). Enable this setting to share one WAN IP address with multiple computers on your network.
  • Page 30 Setup Name — Enter your desired connection name. Click the Apply button to save your changes or click the Cancel button to discard your changes. NOTE: If the IPv6 protocol is selected, the web utility may prompt for you to configure the IPv6 connection settings.

  • Page 31: Wireless Settings

    Setup DNS Server 1 and DNS Server 2 — If provided by your ISP, enter the DNS server. Otherwise, leave these fields blank. As system default route — Check this box to set the current setting as the default route. ICMP Reply Enable —...

  • Page 32: Security Setting

    Setup Wireless Channel — Select the appropriate channel that corresponds to your network settings. You should assign different channels for each access point to avoid signal interference. TIP: Select Auto for Wireless Channel to allow your Wireless Gateway to select the best possible channel for your wireless network.
  • Page 33 Setup Security Mode — Select the security and the encryption type to use. Select None if you do not want to use any security mode. WEP (Wired Equivalent Privacy) is the basic security method. With WEP security, all wireless devices must enter the same key to connect to the network. Authentication Type —...
  • Page 34 Setup WPA / WPA2 Select WPA (Wi-Fi Protected Access) or WPA2 for better encryption. Authentication Type — Select an authentication type. Options are: • PSK: Select to use a passphrase for authentication. If you select PSK, enter a passphrase in the Confirmed Passphrase field. EAP —...
  • Page 35 Setup WPA/WPA2+TKIP/AES Select this security mode if you are unsure which mode is suitable for your wireless devices. Authentication Type — Select an authentication type. Options are: PSK: Select to use a passphrase for authentication. • If you select PSK, enter a passphrase in the Confirmed Passphrase field. •...

  • Page 36: Local Network

    Setup Local Network To access the Local Network page, click SETUP > Local Network. 5.3.1 LAN This section contains the local settings of your network. These settings are private to your internal network and cannot be seen on the Internet. It is recommended to keep the default values.
  • Page 37 Setup The information required on the DHCP Setting screen vary depending on the selected DHCP option. DHCP Option — Select the DHCP mode of your Wireless Gateway. Options are: • Disabled: Select this setting if there is already a DHCP server on your network and all devices on your network use static IP addresses.

  • Page 38: Dhcp Reserved Address

    Setup • Primary DNS Server and Secondary DNS Server — Enter a primary and a secondary DNS server of the sub range. Extra Option Enable — Check this box to enable extra options. • Option 240, Option 241, Option 242, Option 243, Option 244, and Option 245: Enter a name for the corresponding option.

  • Page 39: Time And Date

    Setup Enable — Check this box to enable this function. IP Address — Enter the IP address to reserve. MAC Address — Enter the MAC address of the device to reserve the IP address to. Click the Apply button to save your changes; the reserved IP address is listed on the DHCP Reserved Address table.

  • Page 40: Manual Setup

    Setup Sync By Time Zone Time Zone — Select the time zone in your location. To set the network time and date according to the selected time zone, click the Sync Time button at the bottom of the screen. Sync With NTP Server NTP (Network Time Protocol) —...

  • Page 41: Chapter 6: Advanced

    Advanced Chapter 6: Advanced The Advanced menu configurations greatly affect the operating performance of your Wireless Gateway. This menu is intended for advance users. It is recommended to retain the default settings if you are unsure about them. Advanced Wireless 6.1.1 Wireless Router Settings This page allows you to configure advanced wireless router settings.
  • Page 42 Advanced WMM (Wi-Fi Multimedia) — Select whether to enable or disable WMM. The WMM feature enhances the Quality of Service (QoS) of a network that is used by multimedia applications such as Voice-over-IP (VoIP) and video. If WMM is enabled, multimedia applications on your network have priority over regular data packets, allowing multimedia applications to run smoother and with fewer errors.

  • Page 43: Mbssid Settings

    Advanced 6.1.2 MBSSID Settings This page allows you to configure up to four virtual access points (VAP). Click Advanced > Advanced Wireless > MBSSID Setting or click the MBSSID Setting button. Check the corresponding Enabled box of the VAP to enable it. If you enable a VAP, you can modify its SSID and check its SSID Advertise box to allow wireless devices scanning for a wireless network to detect the VAP.

  • Page 44: Wps Setting

    Advanced To Set MAC Filter Do the following to deny or allow a device to access to the wireless network. 1. On the MAC Address field, enter the MAC address of the device that you want to deny or allow access. 2.

  • Page 45: Multi-Wan

    Advanced Enable WPS — Check this box to prompt WPS-enabled devices to enter the PIN before allowing access to the wireless network. Device Password (PIN) — Displays the PIN password. To generate a new PIN, click the Generate New PIN button. To reset the PIN to default, click the Reset PIN to Default button.

  • Page 46: Ip/Ppp Config

    Advanced 6.2.2 IP/PPP Config This page allows you to create multiple Wide Are Networks (WAN) and manually add an IP or a PPP connection. To access the IP/PPP Config page, click Advanced > Multi-WAN > IP/PPP Config or click the WAN Config button. To add an IP or PPP connection, do the following: 1.

  • Page 47: Advanced-Lan

    Advanced Change Default Route — Select the connection to set as the default route from the drop-down list. Click the Apply button to save your changes or click the Cancel button to discard your changes. Advanced-LAN This page allows you to add multiple LAN IP addresses of the Wireless Gateway. To access the Advanced-LAN page, click Advanced >...

  • Page 48: Ipv6 Wan

    Advanced IPv6 WAN This page allows you to configure IPv6 settings. To access the IPv6 WAN page, click Advanced > IPv6 WAN. The table lists the existing IPv6 connection settings. To edit an entry, click the corresponding icon. To delete an entry, click the corresponding button.

  • Page 49: Autoconfiguration (Stateless/Dhcpv6)

    Advanced DS-Lite — Check this box to enable the Dual-Stack Lite (DS-Lite) function. DS-Lite is used to omit IPv4 address deployment from Customer-premises equipment (CPE) devices but instead use the global IPv6 address provided. AFTR IPv6 Address — Enter an After Family Transition Router (AFTR) IPv6 address. Click the Apply button to save your changes or click the Cancel button to discard your changes.

  • Page 50: Pppoe

    Advanced DS-Lite — Check this box to enable the Dual-Stack Lite (DS-Lite) function. DS-Lite is used to omit IPv4 address deployment from Customer-premises equipment (CPE) devices but instead use the global IPv6 address provided. AFTR IPv6 Address — Enter an After Family Transition Router (AFTR) IPv6 address. Click the Apply button to save your changes or click the Cancel button to discard your changes.

  • Page 51: Ipv6 In Ipv4 Tunnel

    Advanced DS-Lite — Check this box to enable the Dual-Stack Lite (DS-Lite) function. DS-Lite is used to omit IPv4 address deployment from Customer-premises equipment (CPE) devices but instead use the global IPv6 address provided. AFTR IPv6 Address — Enter an After Family Transition Router (AFTR) IPv6 address. Click the Apply button to save your changes or click the Cancel button to discard your changes.

  • Page 52: To 4

    Advanced 6.4.5 6 to 4 On My IPv6 Connection is, select 6 to 4. Connection Name — Select an Internet connection to use. This is the connection that you set up in SETUP > Internet Setup page. See “Internet Setup” on page 21. 6 To 4 Settings Connection Name —...

  • Page 53: 6Rd

    Advanced 6.4.6 6rd On My IPv6 Connection is, select 6rd. Connection Name — Select an Internet connection to use. This is the connection that you set up in SETUP > Internet Setup page. See “Internet Setup” on page 21. 6rd Settings Connection Name —...

  • Page 54: Ipv6 Lan

    Advanced IPv6 LAN After creating IPv6 WAN, create IPv6 LAN to configure local IPv6 addresses. To access the IPv6 WAN page, click Advanced > IPv6 LAN. WAN Interface — Select the IPv6 WAN interface. This is the IPv6 interface that you created in ADVANCED >...

  • Page 55: Ipv6 Lan Stateful

    Advanced Advertise Local Address Prefix — Check this box to advertise the local address prefix. LAN Local Address — Enter the Wireless Gateway LAN local address. IPv6 Local Address Prefix — Enter the IPv6 local address prefix. Available only if Advertise Local Address Prefix is enabled.

  • Page 56: Adsl Settings

    Advanced IPv6 Address Range (max) — Enter the ending range of IPv6 address for your local computers. Lifetime — Enter the advertisement lifetime (in minutes). Click the Apply button to save your changes or click the Cancel button to discard your changes.

  • Page 57: Nat

    Advanced To add RIP settings, do the following: 1. Select the Interface. 2. On the Receive Mode and Send Mode drop-down lists, select the appropriate rsions. NOTE: The selected versions should match the versions supported by the other routers on your network.

  • Page 58: Port Trigger

    Advanced Rule Name — Enter a rule name or select an application name from the drop-down list on the right, then click the << button. If you select a predefined applicatio n name, the Public Port, Private Port, and Protocol Type are automatically configured. DSL Interface —...

  • Page 59: Alg

    Advanced Use Interface — Select a DSL interface from the drop-down list. Trigger Port — Enter the port that will trigger the device to open ports for incoming data. Trigger Port Protocol — Select the trigger port protocol from the drop-down list. Public Port —...

  • Page 60: Vpn Passthrough

    Advanced IRC — Internet Relay Chat (IRC) is a real-time Internet chatting protocol designed fo group communications. Check this box to enable this function to work through your Wireless Gateway. H323 — H.323 is a standard that provides audio-visual communication sessions on a network.

  • Page 61: Firewall

    Advanced Firewall 6.9.1 MAC Filter This page allows you to set up a list of MAC addresses which will be allowed or restricted to access the Internet. To access the MAC Filter page, click ADVANCED > Firewall > MAC Filter or click the MAC Filter button.
  • Page 62 Advanced The table lists the existing filter rules. To edit an entry, click the corresponding icon. To delete an entry, click the corresponding button. To add a filter, click the Add button. The IP Filter Config screen is displayed. IP Filter — Check this box to enable IP filtering. Filter Name —...

  • Page 63: Url Filter

    Advanced 6.9.3 URL Filter This page allows you to deny network devices to access specific URLs or URLs that contain specific keywords. To access the URL Filter page, click ADVANCED > Firewall > URL Filter or click the URL Filter button. URL Filter —...

  • Page 64: Dos Protection

    Advanced 2. Select the time to implement the URL filter or click the New Time Schedule button to create a new schedule. 3. Click the Add button of the Add Keyword Rule. The entry is listed on the URL LIST table. To delete an entry, click the corresponding button.

  • Page 65: Domain Blocking

    Advanced Dos Protection Option — Check the appropriate boxes to enable protection from SYN flood, FIN flood, UDP flood, ICMP flood, SMURF, IP spoofing, and others. Enter the flood count numbers or retain the default values if you are unsure about them. Check the Apply button to save and activate DoS protection or click the Cancel button to discard your changes.

  • Page 66: Spi Settings

    Advanced DMZ — Check this box to enable DMZ. DSL Interface — Select the DSL interface to activate DMZ from the drop-down list. DMZ Host IP Address — Enter the IP address of the computer to set as the DMZ host. Check the Apply button to save and activate DMZ.

  • Page 67: Packet Filter

    Advanced 6.10 Packet Filter 6.10.1 Filters & Rules This page allows you to create packet filters and rules. These filters are used to check each data that passes within your network. If the packet data does not meet the requirements, the packet is either dropped or rejected. To access the Filters &...
  • Page 68 Advanced Filter Name — Select the filter to assign the rule. Enable — Check this box to enable this rule. Ether Type — Select the Ether type: IP (0x800) or IPv6 (0x86DD). Protocol — Select a protocol from the drop-down list. Options are TCP, UDP, or ICMP. Action —...

  • Page 69: Statistics

    Advanced 6.10.2 Statistics This page displays the filter and rule statistics. To access the Statistics page, click ADVANCED > Packet Filter > Statistics or click the Statistics button. Click the Refresh button to refresh the list. 6.11 Static Route This page allows you to create routing tables for IPv4 and IPv6 protocols. To access the Static Route page, click ADVANCED >...

  • Page 70: Multicast

    Advanced IPv6 Static Route Rule Enable — Enable or disable rule. Forwarding Policy Option — Select whether to enable or disable routing. Rule Name — Enter desired rule name. Source IP — Enter the source IP address. Dest IP — Enter the destination IP address. Gateway —...
  • Page 71 Advanced To access the Multicast IGMP page, click ADVANCED > Multicast > IGMP or click the IGMP button. IGMP Proxy IGMP proxy enables your Wireless Gateway to forward multicasts traffics between LAN and WAN networks. 1. On IGMP Option, select Proxy. 2.

  • Page 72: Igmp Snooping

    Advanced 5. Select the DSL Interface to implement IGMP. Connected interfaces are displayed in the Connected Interfaces fields. 6. To enable IGMP fast leave option, check the IGMP Fast Leave box. 7. Enter values for IGMP Query Interval, Robust Count, IGMP Last Member Query Interval, IGMP Robustness, Query Response Interval, and Group Live Delay Time.

  • Page 73: Mld

    Advanced 6. Enter values for IGMP Last Member Query Interval, IGMP Last Member Query Count, Query Response Time, Host Timeout, Leave Timeout, or IGMP Max Groups. If you are unsure about them, leave the default values. 7. Check the Enable IGMP box for WLAN, LAN1, LAN2, LAN3, or LAN4 to enable IGMP in the respective network connection.
  • Page 74 Advanced 4. Enter values for Query Interval, Robust Count, Last Member Query Interval, Last Member Query Count, and Query Response Interval. If you are unsure about them, leave the default values. 5. Click the Apply button to save and apply changes. MLD Snooping With MLD snooping, your Wireless Gateway can make intelligent multicast forwarding to connections that have group members attached in IPv6 protocol.

  • Page 75: Dynamic Dns

    Advanced 6.13 Dynamic DNS Each time your Wireless Gateway connects to the Internet, your ISP assigns a different IP address to your device. In order to access your device from the WAN side, you need to manually track the IP that is currently used. The Dynamic DNS (DDNS) feature allows you to register your device with a DNS server and use the same host name to access your device.

  • Page 76: Ethernet Setting

    Advanced 6.14 Ethernet Setting This page allows you to set the link mode and enable flow control for each of the four LAN ports of your Wireless Gateway. To access the Ethernet Setting page, click ADVANCED > Ethernet Setting. Check the Enable box of the LAN interface to enable the port. Select the LinkMode from the drop-down list.
  • Page 77 Advanced Port Mapping — Select Enabled to enable port mapping. To Create New Groups 1. Click the New button. An empty group appears on the table. 2. Click the radio button to select the empty group. 3. Add members to the group. To do so, select an interface from the Available Interfaces panel.

  • Page 78: Quality Of Service (Qos)

    Advanced 6.16 Quality of Service (QoS) Quality of Service (QoS) is a network standard that assigns the priorities of traffic that passes through your Wireless Gateway. This ensures that demanding real-time applications, such as video streaming, are given priority over other data. 6.16.1 Queue Management This page allows you to enable QoS and choose Differentiated Services Code Point (DSCP) markings to automatically mark incoming traffic without reference to a...

  • Page 79: Queue Classification

    Advanced The table displays QoS queue configurations. To edit an entry, click the corresponding icon. To delete an entry, click the corresponding icon. To configure QoS queue entries, click the Add button. Name — Enter a QoS queue entry name. Enable —...
  • Page 80 Advanced To access the Queue Classification page, click ADVANCED > Quality of Service > Queue Classification or click the QoS Classification button. The table displays QoS queue classification rules. To edit an entry, click the corresponding icon. To delete an entry, click the corresponding icon.

  • Page 81: Qos Status

    Advanced Depending on the selected Ether Type, the succeeding required information may vary. If packet length is used as a criteria, select the Packet Length Rule from the drop- down list and enter the Packet Length. Specify Classification Results Some fields may not be applicable; if so, leave inapplicable fields empty. Assign Classification Queue —...

  • Page 82: Upnp

    Advanced 6.17 UPnP Universal Plug and Play (UPnP) allows automatic discovery and control of services available on the network from other devices without user intervention. This feature is commonly used for gaming and video streaming. If you feel that UPnP is a security concern, disable this feature.

  • Page 83: Snmp

    Advanced 6.18 SNMP Simplified Network Management Protocol (SNMP) is a troubleshooting and management protocol that is used to monitor the status and change the configurations of your Wireless Gateway locally or remotely. It also allows configuring and receiving of trap messages from network devices that are configured for SNMP.

  • Page 84: Chapter 7: Maintenance

    Maintenance Chapter 7: Maintenance The Maintenance menu allows you to configure the web-based utility settings, such as password, remote management, backup/restore options, firmware upgrades, and others. Password Only one user name is allowed to login to the web-based utility of the Wireless Gateway.

  • Page 85: Remote Management

    Maintenance Remote Management This page allows you to enable remote devices to manage your Wireless Gateway using the Hypertext Transfer Protocol (HTTP), Command-Line Interface (CLI), and File Transfer Protocol Daemon (FTPD). To access the Remote Management page, click MAINTENANCE > Remote Management.
  • Page 86 Maintenance HTTP Management Check the Http Enable box to allow network administrators to remotely access the web-based utility via WAN interface. Click the Apply button to save your changes or click the Cancel button to discard your changes. CLI Management Check the TELNET Enable box to allow network administrators to use the command- line interface.

  • Page 87: Remote Access

    Maintenance Remote Access This page allows you to create and edit remote access rules. You can specify the IP address or the subnet mask of devices that are allowed or denied to remotely access your Wireless Gateway and set the type of management service that they can access. To access the Remote Access page, click MAINTENANCE >...

  • Page 88: Init Script

    Maintenance Init Script This page allows you to show, delete, and import initialization scripts running on customer-premises equipment (CPE), such as telephones, routers, or set-top boxes, during system startup or shutdown. To access the Init Script page, click MAINTENANCE > Init Script. Init start scripts are scripts that run before the system starts up.

  • Page 89: Syslog

    Maintenance SysLog This page allows you to enable and configure system logs such as device status, events, and activities. Logs can be sent to the network administrator via e-mail. To access the SysLog page, click MAINTENANCE > SysLog. Log Generate Enable Options Kernel Common Message —...
  • Page 90 Maintenance 4. The succeeding fields may vary depending on the selected location. Enter the necessary information accordingly. 5. Click the Apply button to save your changes or click the Cancel button to discard your changes. E-mail Log Periodically To log e-mails periodically, do the following: 1.

  • Page 91: Time Schedule

    Maintenance Time Schedule This page allows you create desired time schedule. To access the Time Schedule page, click MAINTENANCE > Time Schedule. To create a new schedule, do the following: 1. On the Name field, enter the desired schedule name. 2.

  • Page 92: Configuration Backup/Restore

    Maintenance Click the Browse button and browse for the file. Click the Apply button to start firmware upgrade. WARNING: Do not turn off or press the Reset button on your Wireless Gateway while firmware upgrade is in progress. Doing so will crash the system. Configuration Backup/Restore This page allows you to save a backup of your current settings, revert settings to a...

  • Page 93: Ping

    Maintenance 3. Click the Restore Settings button to restore. Restore Factory Default You can restore the Wireless Gateway to its factory defaults. However, doing so will delete all your settings. To restore the factory defaults, do the following: 1. Click the Restore button. 2.

  • Page 94: Diagnostics

    Maintenance 7.10 Diagnostics This page allows you to test the connectivity of the physical and protocol layers on the WAN side. To access the Diagnostics page, click MAINTENANCE > Diagnostics. To start the test, select the DSL Interface from the drop-down list, and then click the Test button.

  • Page 95: Chapter 8: Status

    Status Chapter 8: Status The Status menu provides the current status and settings of your Wireless Gateway. Summary This page displays the summary of the system, DSL link, ATM PVC, Internet connection, LAN, and wireless ports status. To access the Summary page, click STATUS > Summary. The status is automatically refreshed every 10 seconds.

  • Page 96: Adsl Info

    Status ADSL Info This page displays the status of your DSL line. To access the ADSL Info page, click STATUS > ADSL Info. The status of the ADSL connection is displayed: Status — Displays the ADSL connection status. Total Time — Displays the total time when the Wireless Gateway is connected to ADSL.

  • Page 97: Wireless Clients

    Status The Downstream and Upstream rates are displayed as Current Rate, Max Rate, Noise Margin, Attenuation, and Output Power. The status is automatically refreshed every 10 seconds. To stop automatic refresh, click the Stop Refresh button. Wireless Clients This page displays the clients connected on your network via wireless connection. To access the Wireless Clients page, click STATUS >...

  • Page 98: Logs

    Status Logs This page allows you to view, clear, and backup system logs. To access the Logs page, click STATUS > Logs. You can filter the list by selecting a particular Facility, Severity, Module, or History from the drop-down lists. The log is automatically refreshed every 10 seconds.

  • Page 99: Traffic Meter

    Status The routing table is automatically refreshed every 10 seconds. To stop automatic refresh, click the Stop Refresh button. Traffic Meter This page displays the transmission and reception statistics of packets that pass through the specified interface. To access the Traffic Meter page, click STATUS > Traffic Meter. Traffic Data Interface The table lists the available interfaces on your network.

  • Page 100: Driver Version

    Status Driver Version This page displays the current kernel, Wi-Fi, and DSL driver versions. To access the Driver Version page, click STATUS > Driver Version. 8.10 Statistics 8.10.1 Basic Statistics This page displays the transmission and reception statistics of the Internet connection, LAN device, wireless port, and the LAN ports.

  • Page 101: Statistics > Dsl Statistics

    Status The statistics is automatically refreshed every 10 seconds. To stop automatic refresh, click the Stop Refresh button. 8.10.2 Statistics > DSL Statistics This page displays the transmission and reception statistics of the DSL line. To access the DSL Statistics page, click STATUS > Statistics > DSL Statistics or click the DSL Statistics button.

  • Page 102: Appendix

    Appendix Appendix A. Wireless Considerations Connection Performance A number of factors affect wireless connections. To ensure high-range and stable connectivity, do the following: 1. Keep the Wireless Gateway and other wireless devices away from obstructions, such as walls or buildings. Each obstruction can reduce the range of a wireless device.

  • Page 103: Regulatory & Safety Information

    Appendix B. Regulatory & Safety Information Wireless LAN, Health and Authorization Radio frequency electromagnetic energy is emitted from Wireless LAN devices. The energy levels of these emissions however are far much less than the electromagnetic energy emissions from wireless devices like for example mobile phones. Wireless LAN devices are safe for use frequency safety standards and recommendations.
  • Page 104 Appendix • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
  • Page 105 Appendix EN 300 328 V1.7.1 (2006-10) Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband transmission systems; Data transmission equipment operating in the 2,4 GHz ISM band and using wide band modulation techniques; Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive EN 301 489-1 V1.8.1 (2008-04) Electromagnetic compatibility and Radio Spectrum Matters (ERM);...

  • Page 106: Specifications

    Appendix C. Specifications • Main chip: RTL8672 • AFE: RTL8271B • Ethernet: RTL8305N • WiFi: RTL8188RE • DDR1: 32MB • Flash: 4MB or 8 MB Serial (depends on software requirement) • ADSL2+: POTS User Interface • 1x1 11n 2.4GHz single band •...

Table of Contents