Description Of Control Panel; Preliminary Checks; Checking The Appliance; Installing The Appliance - DeLonghi ESAM 04.110 Instructions Manual

A15. Drip tray
A16. Infuser door
A17. Coffee grounds container
A18. Coffee spout (adjustable height)
A19. Coffee guide
A20. Infuser
A21. Control panel

3.2 Description of control panel

(page 3 - B )
B1. button: turns the appliance on and off (stand-by).
B2. 1 cup and coffee temperature OK light
B3. button: to make 1 cup of coffee
B4. 2 cups and coffee temperature OK light
B5. button: to make 2 cups of coffee
B6. Steam and steam temperature OK light
B7. button: to select the steam function
B8. Coffee quantity selection knob (short, standard or long)
B9. Selection knob to choose coffee taste (for a mild, stand-
ard or strong coffee) or use pre-ground coffee
B10. Steam/hot water knob
B11. light: no water or water tank absent
B12. light: grounds container full or absent
B13. light: general alarm
B14. button to select rinsing or descaling
B15. Descaling light
B16. ECO button to select energy saving mode
B17. Energy saving mode light

4. PRELIMINARY CHECKS

4.1 Checking the appliance

After removing the packaging, make sure the product is com-
plete and undamaged and that all accessories are present.
Do not use the appliance if it is visibly damaged.
Contact De'Longhi Customer Services.

4.2 Installing the appliance

Important!
When you install the appliance, you should respect the follow-
ing safety warnings:
• The appliance gives off heat. After positioning the appli-
ance on the worktop, leave a space of at least 1.18 in/ 3
cm between the surfaces of the appliance and the side and
rear walls and at least 6 in/ 15 cm above the coffee maker.
• Water penetrating the appliance could cause damage. Do
not place the appliance near taps or sinks.
• The appliance could be damaged if the water it contains
freezes. Do not install the appliance in a room where the
temperature could drop below freezing point.
• Arrange the power cable in such a way that it cannot be
damaged by sharp edges or contact with hot surfaces (e.g.
electric hot plates).

4.3 Connecting the appliance

Important!
Check that the mains power supply voltage corresponds to
the value indicated on the rating plate on the bottom of the
appliance.
Connect the appliance to an efficiently earthed and correctly
installed socket with a minimum current rating of 10A only.
If the power socket does not match the plug on the appliance,
have the socket replaced with a suitable type by a qualified
professional.

4.4 Using the appliance for the first time

Please note :
• Coffee has been used to factory test the appliance and it is
.
therefore completely normal for there to be traces of coffee
in the mill.
The machine is, however, guaranteed to be new.
• You should customise water hardness as soon as possible
following the instructions in the section "15. SETTING
WATER HARDNESS" .
1. Remove the water tank (A12), fill to the MAX line with
fresh water then replace in the appliance (fig. 1).
2. Turn the cappuccino maker (A9) outwards and place a
container with a minimum capacity of 3.38 fl.oz. / 100 ml
underneath (fig. 2).
3. Plug the appliance into the mains socket and place the
main switch (A2) on the back of the appliance in the I posi-
tion (fig. 3).
4. The
simultaneously.
5. Turn the steam/hot water knob (B10) a half turn
counterclockwise as far as it will go to position I (fig.
5). Water is delivered from the cappuccino maker
(it is normal for the appliance to make some noise).
6. Wait for delivery of hot water to stop automatically. The
,
must close the steam tap by turning the steam/hot water
knob to the 0 position.
7. Turn the steam/hot water knob to the 0 position. The ap-
pliance goes off automatically.
To use the appliance, turn it on.
9
(B2), (B4),
, lights flash to indicate that you
(B6) lights flash