Neilsen CT0698 Original Instructions Manual

1/4" air angle die grinder, 1/4” air angle grinder kit

Advertisement

Quick Links

1/4" AIR ANGLE DIE GRINDER CT1085
1/4" AIR ANGLE GRINDER KIT CT0698
CT1085
CT0698
ORIGINAL INSTRUCTIONS
Cannon Tools Limited
Address: 20 Station Road, Rowley Regis, West Midlands, B65 0JU.U.K.
SAVE THESE INSTRUCTIONS AND PRECAUTIONS.
READ ALL PRECAUTONS AND INSTRUCTIONS BEFORE USE.

Advertisement

Table of Contents
loading

Summary of Contents for Neilsen CT0698

  • Page 1 1/4" AIR ANGLE DIE GRINDER CT1085 1/4” AIR ANGLE GRINDER KIT CT0698 CT1085 CT0698 ORIGINAL INSTRUCTIONS Cannon Tools Limited Address: 20 Station Road, Rowley Regis, West Midlands, B65 0JU.U.K. SAVE THESE INSTRUCTIONS AND PRECAUTIONS. READ ALL PRECAUTONS AND INSTRUCTIONS BEFORE USE.
  • Page 2: Ec Declaration Of Conformity

    1/4" AIR ANGLE DIE GRINDER Product description: 1/4” AIR ANGLE GRINDER KIT Model: CT1085 CT0698 Applicable EC Directives: EC Machinery Directive 2006/42/EC Harmonized standards EN ISO 11148-9 20 Station Road, Rowley Regis, West Midlands, B65 0JU.U.K.
  • Page 3: Safety Instructions

    1.SAFETY INSTRUCTIONS WARNING– When using tools, basic precautions should always be followed, including the following: 2.General To reduce the risks of electric shock, fire, and injury to persons, read all the instructions before using the tool. 3.Work area a. Keep the work area clean and well lighted. Cluttered benches and dark areas increase the risks of electric shock, fire, and injury to persons.
  • Page 4: Tool Use And Care

    your finger on the switch or connect the tool to the air supply with the switch on. d.Remove adjusting keys and wrenches before connecting an air hose to the Air Angle Die Grinder on. A wrench or a key that is left attached to a rotating part of the tool increases the risk of personal injury.
  • Page 5: Air Source

    repaired. d.Disconnect the tool from the air source before making any adjust- ments, changing accessories, or storing the tool. Such preventive safety measures reduce the risk of starting the Air Angle Die Grinder unintentionally. Turn off and detach the air supply, safely discharge any residual air pressure, and release the throttle and/or turn the switch to its off position before leaving the work area.
  • Page 6: Vibration Precautions

    a.Never connect to an air source that is capable of exceeding 200 psi. Over pressurizing the tool may cause bursting, abnormal operation, breakage of the tool or serious injury to persons. Use only clean, dry, regulated compressed air at the rated pressure or within the rated pressure range as marked on the tool.
  • Page 7: Functional Description

    the tool do the work. g.To reduce vibration, maintain tool as explained in this manual. If abnormal vibration occurs, stop immediately. 9.Functional Description Specifications Max. speed: 20000/min Max air pressure: 6.2bar Avg. air consumption: 3cfm Air inlet :1/4" Max. chuck size: 1/4" Hose size: 3/8”...
  • Page 8 1. Incorporate an in-line oiler, shut-off valve, regulator with pressure gauge, and filter for best service, as shown in the diagram above. An in-line shut off valve is an important safety device because it controls the air supply even if the air hose is ruptured. Note: If an automatic oiler system is not used, add a few drops of Pneumatic Tool Oil to the airline connection before operation.
  • Page 9: Operating Instructions

    Note: Air flow, and therefore Air Angle Die Grinder performance, can be hindered by undersized air supply components. a. The air hose must be long enough to reach the work area with enough extra length to allow free movement while working. b.
  • Page 10 4. Insert 1/4” diameter shank of a Grinding Accessory (not included) fully into Collet Nut. Then, firmly re-tighten Collet Nut to lock both the Collet and Grinding Accessory in place. 5. Connect air supply hose to Air Inlet. Turn on air compressor and set its regulator to the maximum 90 PSI for Die Grinder.
  • Page 12 CANNON TOOLS LTD Add: 20 station road, Rowley Regis, west midlands,B65 0JU.U.K. Made in China...

This manual is also suitable for:

Ct1085

Table of Contents