Pioneer PDP-614MX Operating Instructions Manual page 21

Symptom
Mechanical sound is heard.
• Maybe the sound from the cooling fans used to prevent over heating.
The unit emits a crackling sound. • Are the image and sound normal?
Picture is disturbed. • Is a connected component set directly in front or at
Sound is noisy. the side of the display?
Remote control operates erroneously.
The remote control does not work. • Are the remote control's batteries worn out?
• Is IR REMOTE set to ON?
• Has an ID number been set for the main unit?
Monitor's power does not turn on when the • Is the monitor's power cord plugged into a power
remote control's power button is pressed. outlet?
• Are all the monitor's indicators off?
• Are the remote control's batteries worn out?
• Is IR REMOTE set to OFF?
• Has an ID number been set for the main unit?
Monitor does not operate when the remote • Is the remote control pointed at the monitor, or is
control's buttons are pressed. there an obstacle between the remote control and
the monitor?
• Is direct sunlight or strong artificial light shining on
the monitor's remote control sensor?
• Are the remote control's batteries worn out?
• The remote cable is plugged into the REMOTE IN
terminal (Wired).
The front panel buttons of the main unit do • The front panel buttons do not function during KEY
not function. Lock.
No sound or picture is produced. • Is the monitor's power cord plugged into a power
outlet?
Picture appears but no sound is produced. • Is the volume set at the minimum?
• Is the MUTING mode set?
• Are the speakers properly connected?
• Is AUDIO INPUT set correctly?
Poor picture with VIDEO signal input. • Improper control setting.
Local interference.
Cable interconnections.
Input impedance is not correct level.
Poor picture with RGB signal input. • Improper control setting.
Incorrect RGB connector pin connections.
Tint is poor or colors are weak. • Are the tint and colors properly adjusted?
Nothing appears on screen. • Is the computer's power turned on?
• Is a source connected?
• Is the power management function in the standby
or off mode?
• Is LOOP OUT set to ON?
Part of picture is cut off or picture is not • Is the position adjustment appropriate?
centered.
Image is too large or too small. • Is the screen size adjustment appropriate?
Picture is unstable. • Is the computer's resolution setting appropriate?
STANDBY/ON indicator is lighted in red. • Horizontal and / or vertical sync signal is not
present when the Intelligent Power Manager
control is on.
STANDBY/ON indicator is blinking in red. • The temperature inside the main unit has become
too high and has activated the protector.
STANDBY/ON indicator is blinking in green
and red, or green.
32
En
Checks Remedy
• If there are no abnormalities in the image and sound,
the noise is caused by the cabinet reacting to
changes in temperature. This will not affect
performance.
• Leave some space between the display and the
connected components.
• Replace both batteries with new ones.
• Set IR REMOTE OFF on OPTION3 menu.
• Set an ID number with the ID NO. SET button, or set
the ID number to ALL.
• Plug the monitor's power cord into a power outlet.
• Press the power button on the monitor to turn on the
power.
• Replace both batteries with new ones.
• Set IR REMOTE ON.
• Set an ID number with the ID NO. SET button, or set
the ID number to ALL.
• Point the remote control at the monitor's remote
control sensor when pressing buttons, or remove the
obstacle.
• Eliminate the light by closing curtains, pointing the
light in a different direction, etc.
• Replace both batteries with new ones.
• Unplug the remote cable from the monitor.
• Set the KEY Lock to OFF.
• Plug the monitor's power cord into a power outlet.
• Increase the volume.
• Press the remote control's MUTING button.
• Connect the speakers properly.
• Set AUDIO INPUT on the SOUND menu correctly.
• Adjust picture control as needed.
Try another location for the monitor.
Be sure all connections are secure.
• Adjust picture controls as needed.
Check pin assignments and connections.
• Adjust the tint and color (under PICTURE).
• Turn on the computer's power.
• Connect source to the monitor.
• Operate the computer (move the mouse, etc.).
• Set LOOP OUT OFF.
• Adjust the SCREEN properly.
• Press the SCREEN SIZE button on the remote
control and adjust properly.
• Set to the proper resolution.
• Check the input signal.
• Promptly switch off the power of the main unit and
wait until the internal temperature drops. See*1.
• Prompty switch off the power of the main unit. See
— — — — — —
*2.
Screen Size
Aspect Ratio
Resolution
Signals
Synchronization Range
Input Signals
Input Terminals
(VIDEO1 and PC1 can also be used as OUTPUT terminals)
PC
Visual 1 (Analog)
Visual 2 (Analog)
Visual 3 (Digital)
Video
Visual 1
Visual 2
Visual 3
COMPONENT
Visual 1
Visual 2
Audio
RS-232C
Sound output
Power Supply
Current Rating
Power Consumption
Dimensions
Weight
Environmental Considerations
Operating Temperature
Other Features
33
En