Pioneer PRO-1410HD Field Service And Training Manual
  1. Manuals
  2. Brands
  3. Pioneer Manuals
  4. Plasma TV
  5. Elite PureVision PRO 1410HD
  6. Field service and training manual

Pioneer PRO-1410HD Field Service And Training Manual

42 & 61 inch plasma
Hide thumbs Also See for PRO-1410HD:
Table of Contents

Advertisement

Quick Links

42 & 61 Inch Plasma
Field Service and Training Guide
PRO-1410HD
PDP-614MX
PDP-424MV
Technical Training Department
1925 E. Dominguez Street
Long Beach, CA 90810

Advertisement

Table of Contents
loading

Related Manuals for Pioneer PRO-1410HD

Summary of Contents for Pioneer PRO-1410HD

  • Page 1 42 & 61 Inch Plasma Field Service and Training Guide PRO-1410HD PDP-614MX PDP-424MV Technical Training Department 1925 E. Dominguez Street Long Beach, CA 90810...
  • Page 3 Remote Troubleshooting (Flow Chart) 21~22 All Connector Locations Closed Caption Troubleshooting (Flow Chart) 23~24 Screw Locations On PCB Assemblies 61 Inch Section (PRO-1410HD & PDP-614MX) 26~49 Parts List (42 Inch Model) 65~66 Testing Scan Board (Y-Drive) Adjustments (42 Inch Model)
  • Page 4 Safety information harm. (California Health and Safety Code Section 25249.5). Important safety data for this Pioneer model is contained in the service manual. Before returning the unit to the customer, complete all product safety obligations and tests.
  • Page 5 PDP-424MV PCB Layout SENB PWB POWER UNIT MAIN PWB High Voltage SEND PWB 232C PWB SENC PWB PWR PWB AUDIO PWB CTL PWB LED PWB...
  • Page 6 PRO-1410HD & PDP-614MX SENB PWB SEND PWB MAIN PWB POWER UNIT Scanning PWB 232C PWB SENC PWB PWR PWB AUDIO PWB CTL PWB LED PWB...
  • Page 7 Function of the PCB’s MAIN PWB ASSY Selector Video selector(Video, RGB/YC/V) Sync selector(Sync on green, HD,VD,Y) Video decoder 3.58NTSC Motion compensated 3D Y/C separation PAL Motion compensated 2D Y/C separation Color demodulation Digital chroma decoder DVI receiver HDCP...
  • Page 8 Function of the PCB’s MAIN PWB ASSY AD converter IP converter Resolution converter(Frame rate converter) Contrast,Bright Color temperature adjustment De-Gamma converter(Error diffusion,Dither) LVDS(Low voltage differential signal) OSD(On screen display) SPLIT SCREEN...
  • Page 9 Function of each PWB AUDIO PWB ASSY AUDIO AMPLIFIER SENB PWB,SENC PWB ,SEND PWB Temperature sensor 232C PWB Remote in-out, 232C input terminal CTL PWB INPUT SELECT/EXIT,LEFT/+,RIGHT/+ VOLUME UP/DOWN,PROCEED PWR PWB Power switch LED PWB POWER/STANDBY LED POWER UNIT...
  • Page 10 Normal Power On Operation 61 & 42 Fan C 61 Only IC9503...
  • Page 11 42 And 61 Inch Models Normal Power On Operation 1. AC line attached to Power Supply. 2. Power Supply outputs a Power Mute voltage at +4.8 from Connector PM pin 5 (POMUTE). The Power Supply also outputs a +7 volt supply to the Main Microprocessor at Connector PM pin 1 (M+7).
  • Page 12 42 & 61 Inch Common Trouble Shooting Page: Trouble Area: Power Failure 14 & 15 Blinking in Green Blinking in Red Blinking in Red & Green Lighting Green then Red No Picture Audio 21 &22 Remote 23 &24 Closed Caption...
  • Page 13 PDP-614MX / PRO-1410HD / PDP-424MV (Caution) If any abnormality is sensed in such a 1. Power failure manner that the LED flashes or lights, all the power lines other than those of 7Vdc (M+7V) and 5Vdc (M+5V) are automatically (1) The power supply is not turned on.
  • Page 14 (2) Blinking in green Alarm of te mperature sensor error  Blinking in green (intervals of 2 seconds) Turn off the main power supply. Pressing the [MENU] key of the product, turn on the main power supply to cancel alarming. FAN SET Press the remove control keys in the sequential order of [POWER ON] →...
  • Page 15 Alarm of fan error  FAN SET FAN MODE CONT ENA – FAN OFF/L – CONT UP – Blinking in green (intervals of – CONT TIME – 0.5seconds) – UP STEP FAN SAVE DOWN STEP PLE SAVE READ TIME T ALM TEMP LEVEL RET TME Turn off the main power supply.
  • Page 16 (3) Blinking in red (Alarm of temperature error) Since the internal temperature is too high in the product, the temperature protector has been actuated. In such a case, the following actions should be taken immediately: 1. Turn off the main power supply and pull out the power cord from the wall outlet. 2.
  • Page 17 (4) Alternation blinking in red and green (Alarm of PDP error) (Caution) How to reset the alarming condition Pressing the [Input Select] key of the product, turn on the main power supply of the main unit. In this state, keep pressing the [Input Select] key for more than 2 seconds until alarming is canceled.
  • Page 18 (5) Lighting in green, and then in red (Alarm of power voltage error) Unlike [lighting in red] in the STANDBY mode, [lighting in green] continues for about 30 seconds without any output of images and audio signals. Since then, the mode turns into [lighting in red]. (Caution) How to reset the alarming condition The Lighting in red alarming condition can be reset when an...
  • Page 19 (8) No pictures [(Caution) The voltage outputs of Vs = 170V and Vd = 64V, 5Vdc are always generated, but the LED is not flashing or lighting for alarming. However, the voltage values will differ according to the MODULE.] No picture is displayed. Make the setting of OFF→...
  • Page 20 3. Audio errors (Caution) In regard to the method of audio input setting, refer to the specifications and the instruction manual to confirm that all the setting is correct. Then, troubleshooting can be carried out. It must be noted that the protector functions and no audio output is available if the opposing electrodes of the speaker output or the speaker output and the ground (GND) are short-circuited.
  • Page 21 4. Remote control not effective (1) The wired remote control is not effective. When a single item is used  (Caution) The wired remote control is not effective if the setting of [PLE LINK], or [Repeat TIMER] is ON, or if the The wired remote control is not setting of [ID NUMBER] has been made.
  • Page 22 (2) The wireless remote control is not effective. (Caution) Since the detection of “wired” or “wireless” is conducted for the remote control through the remote terminal, it is necessary to pull out the remote control cable from the remote terminal. Troubleshooting should be carried out after confirming that “IR REMOTE”...
  • Page 23 5. The closed caption (CC) is displayed incorrectly.) (Note) Only the models for North America. The PCB-5044 (CCD PWB) is not installed in other models. Checks are needed by applying a signal output to the video input circuit, which is equivalent to the closed caption.
  • Page 24 3.3V <Fig. 1 CCD PWB Pattern Diagram>...
  • Page 25 61 Inch Section (PRO-1410HD & PDP614MX) Page: Topics Covered: Testing Scan board (Y drive) Testing Scan IC’s and Common board (X drive) Testing Data IC’s & Digital board fuse 29~30 PC board replacement (screws & connector locations) 31~37 Adjustments 38~41...
  • Page 26 Points of failure diagnosis for a Board Assy (PKG) The fuses and/or fusible resistors shown in the photos below may be blown by electric surges caused by a failure. In such a case, replace the corresponding PKG. Failure diagnosis of the Scanning Board (Y-Drive) Fusible resistor (R12) located Glass fuses (F1 and F2) at the upper-left corner of the...
  • Page 27 Failure diagnosis of the Scanning IC Check with a tester the resistance value between any pins indicated as NEGA and POSI of the connector in the photos below. If a positive and a negative pin of the connector on the Scanning Relay PKGs are short-circuited and remains short-circuited even after the connectors on the Scanning PKG and Scanning Relay PKG are disconnected, the Scanning IC on the Scanning Relay PKG is in failure.
  • Page 28 Failure diagnosis of the Data IC Failure symptom: The image in any block of the screen is not displayed. Check with a tester between Pin 5 or 6 (Vd line of Data IC) and ground of each Signal Relay PKG. OK: Open NG: Short- circuited,...
  • Page 29 Replacement method for a Board Assy and notes on replacement Preparation Place a cushion on the workbench and set the module to be repaired on it. Note: With the glass surface facing downward, be sure that the entire glass surface is against the cushion.
  • Page 30 How to remove/reattach the Board Assy (PKGs) Notes: · Be sure not to drop a screwdriver or screw on a PKG or a cable. · When removing/reattaching a screw, be sure not to leave any tiny metal shavings, because they may cause a failure. ·...
  • Page 31 PDP-614MX & PRO-1410HD METHOD OF ADJUSTMENTS ■Adjusting conditions Adjustments should be carried out in the procedures of A to C specified below. However, any adjustments other than the items A to C below are not required. When the “PDP module (PDP-NP61C2MF01)” is replaced, adjustments should conform to the adjusting items of [1 and 2] specified below.
  • Page 32 2. Adjustment of the power unit (Using a screwdriver for general-purpose adjustments) 2-1. Adjustment of the Vs voltage (1) Enter a color bar input by means of either video signal of VIDEO input, or DVD/HD input, or RGB input, and turn on the power switch of the main unit. (2) Turn the volume control (RV6) in the power unit and make adjustments until the voltages of CH2 and CH1 (D, GND) of the power unit attain the voltage values specified for the PDP (Vs value of the voltage regulation indicator label on below the figure) ±1V.
  • Page 33 * Top view of the power unit (Adjustment VR location) D.GND Adjustmen t of 5V D+70 ADJ Adjustment of D+3.3 ADJ the Vs voltage D+5 ADJ D+170 ADJ Adjustment of the Vd voltage...
  • Page 34 3. Adjustments after the replacement of the MAIN PWB (Using the remote control) 3-1. Product serial No. registration (1) Press the keys in the order of [POWER ON] → [POWER ON] → [EXIT] → [DISPLAY] in order to enter the factory adjustment menu. (2) Press the [MENU/ENTER] key to select the [MONITOR INFORMATION] No.
  • Page 35 (Example) When entering a serial number of [DISS00001XX] Move the POSITION/CONTROL keys of [ ] and [ ] to select [2].  MONITOR INFORMATION MODEL NAME PDP-614MX SERIAL/NUMBER SOFT WARE VERSION F123 USAGE TIME 00000H T1 025 T2 025 T3 025 T4 - - [MENU/ENTER] NEXT [EXIT] PREV...
  • Page 36 ] to select [DESTINATION ALPHABETS] shown below. (The asterisks * shown below denote the numerals or the characters.) J : PDP-615PRO : Specifications for use in Japan A : PDP-614MX / PRO-1410HD : Specifications for North America G : PDP-615EX : Specifications for European countries...
  • Page 37 FUNCTION SCART SAFEL MODE--- SHIP PLE TEST OFF -- LIMIT-VD VD2 VLIM LIMIT-PC VD2 YCORB GAMMA MD VD2 YCOREN ON VOL OFFSET VD2 CORB FHCRT COMP VD2 COREN ACTVH TIME VD OUT PSC-T ROTATE PTN EXT-PC BLUE GAIN [MENU/ENTER] NEXT [EXIT] PREV (4) Press the keys of the remote control in the order of [POWER ON] →...
  • Page 38 Removing the BACK COVER (5)SRW33 (5)SRW33 PL-CPIMS*4*12*15KFE PL-CPIMS*4*12*15KFE 29N01431 *14p 29N01431 *14p (1)SRW34 (4)SRW32 (1)SRW34 (4)SRW32 PL-CPIMS*4*16*3KF CBIPS*4*12*15KFE PL-CPIMS*4*16*3KF CBIPS*4*12*15KFE 910E4066 *4p 29N01401 *12p 910E4066 *4p 29N01401 *12p (2)M18 HANDLE (2)M18 HANDLE 29F00591 *2p 29F00591 *2p M31 GS COVER M31 GS COVER 29H02782 29H02782 M57 NAME PLATE...
  • Page 39 Removing the POWER UNIT (2)PSU POWER UNIT (2)PSU POWER UNIT 3S110161 3S110161 (1)SRW14 PL-CPIMS*4*12*15KFE (1)SRW14 PL-CPIMS*4*12*15KFE 29N01441 *6p 29N01441 *6p...
  • Page 40 Removing the upper CHASSIS ASSY (6)SRW05,06 PL-CPIMS*6*20*15KFE (6)SRW05,06 PL-CPIMS*6*20*15KFE 29N01451 *10p 29N01451 *10p (5)CONNECTOR 4p (5)CONNECTOR 4p (7)SRW07,08,09,11,13 (7)SRW07,08,09,11,13 (Caution) Remove the ferrite (Caution) Remove the ferrite PL-CPIMS*4*12*15KFE PL-CPIMS*4*12*15KFE core first. core first. 29N01441 *22p 29N01441 *22p (4)CONNECTOR (4)CONNECTOR (3)SRW17 TP-M3*6*3KF (3)SRW17 TP-M3*6*3KF 24N04581 24N04581...
  • Page 41 PDP Panel Assembly (4)CN-PH CN 9P(PH) 360W,1007-20 (4)CN-PH CN 9P(PH) 360W,1007-20 (5)PDP PDP-NP61C2MF01AA (5)PDP PDP-NP61C2MF01AA 7SW9W008 7SW9W008 3S361002 3S361002 (3)CN-PD CN 10P(PD) 920W,1007-20 (3)CN-PD CN 10P(PD) 920W,1007-20 7SW0W010 7SW0W010 (2)CN-AD CABLE 31P L390 (2)CN-AD CABLE 31P L390 7S530036 7S530036 (1) SCREW (1) SCREW (Caution) This screw is used (Caution) This screw is used...

  • Page 42: Pdp Module

    PDP MODULE PARTS LIST (61 Inch Models) PART NAME PART No. NOTE NAME VER *1 1 Scanning PKG 1 PKG61C2F1 9S899790 2 PKG61C2G1 9S899669 1 Common PKG 3 PKG61C2C1 05C-27 9S899791 1 Digital PKG PKG61C2C1 05D-27 9S899731 Cf. interchangeability list PKG61C2C1 05C-28 9S899792...
  • Page 43 Board ASSY interchangeability list 61 Inch Models) Note: In the Board ASSY (PKG) replacement, You can exchange it in a version of high rank than a replacement target version besides a compatible version. Digital PKG follows the following list, and exchange it. Replacement Target Version Compatible Version Digital PKG...
  • Page 44 CONNECTOR PIN EXPLANATION PDP-614MX & PRO-1410HD (Caution) The operating voltages specified below are used in common irrespective of the presence of signals. In this case, however, part of the operating voltages (red characters) may change according to the signal conditions when the main power supply is turned on (POWER button ON).
  • Page 45 Basic operation (Numerical unit: Vdc; except for the case when units are individually indicated) Main power ON AC power ON AC power OFF (POWER button ON) ★ (Power cord (Power cord Power Main power Standby Name Pin No. Pin name Function Signal direction connected to...
  • Page 46 Basic operation (Numerical unit: Vdc; except for the case when units are individually indicated) Main power ON AC power ON AC power OFF (POWER button ON) ★ (Power cord (Power cord Power Main power Standby Name Pin No. Pin name Function Signal direction connected to...
  • Page 47 Basic operation (Numerical unit: Vdc; except for the case when units are individually indicated) Main power ON AC power ON AC power OFF (POWER button ON) ★ (Power cord (Power cord Power Main power Standby Name Pin No. Pin name Function Signal direction connected to...
  • Page 48 Basic operation (Numerical unit: Vdc; except for the case when units are individually indicated) Main power ON AC power ON AC power OFF (POWER button ON) ★ (Power cord (Power cord Power Main power Standby Name Pin No. Pin name Function Signal direction connected to...
  • Page 49 Basic operation (Numerical unit: Vdc; except for the case when units are individually indicated) Main power ON AC power ON AC power OFF (POWER button ON) ★ (Power cord (Power cord Power Main power Standby Name Pin No. Pin name Function Signal direction connected to...
  • Page 50 42 Inch Section (PDP-424MV) Page: Topics Covered: Missing Data or Scan Symptoms 52~53 Testing Data Relay boards 54~55 Testing High Voltage board and Scan IC’s 56~57 Testing High Voltage board for no picture Digital board Symptoms 59~61 Power Off Symptoms Picture problems (High Voltage) All Connector locations Screw locations on PCB’s...
  • Page 51 (Note) Typical Symptom are only shown. Another Symptom might appear. Symptom: Vertical line Block PDP-424MV Data/Address line problems Cause/Countermeasure: Cause/Countermeasure: ①Open or contact failure of connector between Data Relay Board ① Open or contact failure of Data flexible Cable⇒Clean, and Digital Board/High Voltage Board⇒ Clean, Reconnect or Reconnect or exchange connector.
  • Page 52 Testing Data Relay Boards and IC's Cause/Countermeasure: ② If the connector CN7709 disconnected from Data Relay Board (RU) is short-circuited between Pin 1 (or 2) and GND (Pin 3 or 4) ⇒Data IC is broken ⇒ PDP. ③ If the connector CN7709 disconnected from Data Relay Board (RU) is short-circuited between Pin 5 (or 6) and GND (Pin 3 or 4) ⇒...
  • Page 53 Cause/ Countermeasure : ④ If the connector CN7909 disconnected from Data Relay Board (RD) is short-circuited between Pin 1 (or 2) and GND (Pin 3 or 4) ⇒Data IC is broken ⇒ PDP. ⑤ If the connector CN7909 disconnected from Data Relay Board (RD) is short-circuited between Pin 5 (or 6) and GND (Pin 3 or 4) ⇒...
  • Page 54 Testing High Voltage board and Scan IC's Symptom:No Picture. (Priming doesn’t flash if W-X terminals are short-circuited.) High Voltage Board; Reverse (112) (1~4) (109) PH2401 (107) Ｆ (6~9) Cause/Countermeasure: No Diode characteristic ⇒ Exchange High (10~13) (99~103) Voltage Board. Checkpoints (15~18) (93~96) (91)
  • Page 55 High Voltage Scan Relay Board (U) Board NEGA Cause/Countermeasure: If short-circuited, disconnect connector between High Voltage Board and Scan Relay Board and, ④ Short between NEGA-POSI on High Voltage Board 　　　　　　　　　　 Exchange High Voltage Board. 　　　　　　　　　　　　　　　　　　⇒ ⑤ Short between NEGA-POSI on Scan Relay Board (U)　 POSI Exchange Scan Relay Board (U).
  • Page 56 Picture Defect High Voltage Board Glass Fuse (F302) (Note) Typical symptom are only shown. Another Symptom might appear. Symptom:No Picture(Priming flash). OK: Short NG: Open Cause/Countermeasure: ①F302 open⇒ Exchange High Voltage Board. NEC Plasma Display...
  • Page 57 Symptom: No Picture( Priming doesn’t flash) R146 OK: About 4.7Ω (2W) 　　　 NG: Open　 Cause/Countermeasure: R146 open⇒ Exchange High Voltage Board. R146 NEC Plasma Display...
  • Page 58 Symptom: Abnormalities in a picture One or more vertical bands, Transparent vertical band Out of synchronization or Multiple vertical lines duplication A number of lateral lines, Rectangular color shear, color Mosaic Regular noise discrepancy, shear in display Cause/Countermeasure: ① Contact failure of connector adjacent to Digital Board or short circuit due to conductive obstacle Clean or Reconnect ⇒...
  • Page 59 Power off (Note) Typical Symptom are only shown. Another Symptom might appear. Symptom: No Picture(Priming doesn’t flash) High Voltage Board ⇒ Power off OK: Short NG: Open Cause/Countermeasure: ①F301 open ⇒ Exchange 　　　　　　　　　　　　　　　　　　High Voltage Assy 　　　　　　 　②FU801 open ⇒ Exchange Digital Assy Glass Fuse (F301) Digital Board OK: Short...
  • Page 60 Cause/Countermeasure: ③ F1 open ⇒ Exchange High Voltage Board. High Voltage Board 　　 OK: Short 　　 NG: Open NEC Plasma Display...
  • Page 61 Symptom: No Picture ⇒Power off(Priming flash) High Voltage Board Fuse Resistor (Ｒ91) Cause/Countermeasure: R91 open ⇒ Exchange 　 　High Voltage Board.　 高圧ＰＫＧ R91 OK: About 2.2Ω (1W) 　　　 NG: Open　 NEC Plasma Display...
  • Page 62 Symptom: White Ｐａｔｔｅｒｎ even in Symptom: Failure in Writing⇒ no signal 　⇒ Power off Power off Dark and rough picture Cause/Countermeasure: R150 open ⇒ Exchange High Voltage Board. Many light spots on dark portion Cause/Countermeasure: R43,R61 open⇒ Exchange High Voltage Board. Fuse Resistor (R150) Fuse Resistor (R43),(R61) R43　OK: About 3.3Ω(2W)
  • Page 63 Connectors and cables all PCB's. (Caution) Be careful of handling cables and connectors to avoid Failure. Be sure to take off Heat Sink before detaching Data Relay Board. Data Relay Board (LU) Data Relay Board (RU) 9 connectors 8 connectors Common Relay Board 1 connector High Voltage...
  • Page 64 Screw locations all PCB's. (Caution) Be careful not to leave a screw or screw dust. Be sure to take off Heat Sink before detach Data Relay Board. See the next page for the procedure. Data Relay Board (LU); 3 screws Data Relay Board (RU);...

  • Page 65: Parts List

    PARTS LIST PDP-424MV PART NAME PART NO NOTE SYMBOL TYPE NAME VERSION PKG42B3G1 9S899523 High voltage PKG PKG42B3J4 9S899627 Common divergence PKG PKG42B3J3 9S899282 Common relay PKG PKG42B3J1 9S899524 Signal relay PKG (left) PKG42B3J2 9S899525 Signal relay PKG (right) PKG42B3E1 9S899351 Scanning relay PKG-U PKG42B3E1...
  • Page 66 Compatible table of the board version Compatible Version Part Name of PKG Target Version Conditions Remarks High voltage PKG Common divergence PKG Common relay PKG Signal relay PKG (left) Signal relay PKG (right) Scanning relay PKG-U Scanning relay PKG-D Digital PKG Note: By referring to the table on compatible versions of the board assys, make sure that board assys of compatible versions are used.
  • Page 67 PDP-424MV METHOD OF ADJUSTMENTS ■Adjusting conditions Adjustments should be carried out in the procedures of A to C specified below. However, any adjustments other than the items A to C below are not required. When the “PDP module” is replaced, adjustments should conform to the adjusting items of [1 and 2] specified below.
  • Page 68 2. Adjustment of the power unit (Using a screwdriver for general-purpose adjustments) 2-1. For the PX-42VM5/42VP5/42VR5,PX-42XM3/42XR3 Series 2-1-1. Adjustment of the Vs voltage (1) Enter a color bar input by means of either video signal of VIDEO input, or DVD/HD input, or RGB input, and turn on the power switch of the main unit.
  • Page 69 * Top view of the power unit for the PX-42VM5/42VP5/42VR5,PX-42XM3/42XR3 Series TP203 TP204 D+170 (D+180) Adjustmen t of 5V TP205 D.GND Adjustment of TP206 D+60 the Vs voltage (D+65) RV203 D+170 ADJ RV204 D+60 ADJ (D+65) Adjustment of the Vd voltage RV201 D+5 ADJ (Caution) The values in ( ) are applicable to the PDP-424MV.
  • Page 70 3. Adjustments after the replacement of the MAIN PWB (Using the remote control) 3-1. Product serial No. registration (1) Press the keys in the order of [POWER ON] → [POWER ON] → [EXIT] → [DISPLAY] in order to enter the factory adjustment menu. (2) Press the [MENU/ENTER] key to select the [MONITOR INFORMATION] No.
  • Page 71 • How to read the serial number Serial No.        ················· Year of manufacture (lower one digit of the year)  ················· Month of manufacture (January to September = 1 to 9, October = X, November = Y, December =Z) ...
  • Page 72 Repeat the procedures of above, and enter all inputs of [2900123 9Z] from the left side.    MONITOR INFORMATION MODEL NAME PX-61XM3A SERIAL/NUMBER : 29001230 9Z SOFT WARE VERSION F123 (Caution) Give a one-digit space between the 7th USAGE TIME 00000H and 8th digits.
  • Page 73 FUNCTION SCART SAFEL MODE--- SHIP PLE TEST OFF -- LIMIT-VD VD2 VLIM LIMIT-PC VD2 YCORB GAMMA MD VD2 YCOREN ON VOL OFFSET VD2 CORB FHCRT COMP VD2 COREN ACTVH TIME VD OUT PSC-T ROTATE PTN EXT-PC BLUE GAIN [MENU/ENTER] NEXT [EXIT] PREV (4) Press the keys of the remote control in the order of [POWER ON] →...
  • Page 74 REMOVING BACK COVER M06 SERIAL LABEL M06 SERIAL LABEL 24L44731 24L44731 (4) BACK COVER ASSY M61 NAME PLATE M61 NAME PLATE (4) BACK COVER ASSY (Caution) This is not a service part. (Caution) This is not a service part. (3)SRW25 PTN3*12*15KFE (3)SRW25 PTN3*12*15KFE 29N01491 *6p 29N01491 *6p...
  • Page 75 REMOVING POWER UNIT (1) SRW16 TP-M3*6*3KF (1) SRW16 TP-M3*6*3KF (2)A11 POWER UNIT (2)A11 POWER UNIT 24N04581 5p 24N04581 5p 3S110211 3S110211...
  • Page 76 REMOVING CHASSIS ASSY (1) SRW10 CBIPS*4*12*15KFE (8) SRW32 SCREW PL-CPIMS*3*10*15KFE (1) SRW10 CBIPS*4*12*15KFE (8) SRW32 SCREW PL-CPIMS*3*10*15KFE 29N01401 *2p 29N01431 *2p 29N01401 *2p 29N01431 *2p (6) CONNECTOR (6) CONNECTOR (11) CHASSIS ASSY (11) CHASSIS ASSY (7) CONNECTOR 2p (7) CONNECTOR 2p (3) SRW08 CBIPS*3*8*3KF (3) SRW08 CBIPS*3*8*3KF 24N03691 *4p...
  • Page 77 PDP PANEL VIEW WITH CHASSIS REMOVED M14 LUG(L60) M14 LUG(L60) 29C01471 29C01471 SRW17 TP-M3*6*3KF SRW17 TP-M3*6*3KF 24N04581 24N04581 (Caution) For use, remove these eight blocks that (Caution) For use, remove these eight blocks that are attached to the maintenance PDP. are attached to the maintenance PDP.
  • Page 78 CONNECTOR PIN EXPLANATION PDP-424MV (Caution) The operating voltages specified below are used in common irrespective of the presence of signals. In this case, however, part of the operating voltages (red characters) may change according to the signal conditions when the main power supply is turned on (POWER button ON). Status of LED lighting: ★...
  • Page 79 Basic operation (Numerical unit: Vdc; except for the case when units are individually indicated) Main power ON AC power ON AC power OFF (POWER button ON) ★ (Power cord (Power cord Power Main power Standby Name Pin No. Pin name Function Signal direction connected to...
  • Page 80 Basic operation (Numerical unit: Vdc; except for the case when units are individually indicated) Main power ON AC power ON AC power OFF (POWER button ON) ★ (Power cord (Power cord Power Main power Standby Name Pin No. Pin name Function Signal direction connected to...
  • Page 81 Basic operation (Numerical unit: Vdc; except for the case when units are individually indicated) Main power ON AC power ON AC power OFF (POWER button ON) ★ (Power cord (Power cord Power Main power Standby Name Pin No. Pin name Function Signal direction connected to...
  • Page 82 Basic operation (Numerical unit: Vdc; except for the case when units are individually indicated) Main power ON AC power ON AC power OFF (POWER button ON) ★ (Power cord (Power cord Power Main power Standby Name Pin No. Pin name Function Signal direction connected to...
  • Page 83 Basic operation (Numerical unit: Vdc; except for the case when units are individually indicated) Main power ON AC power ON AC power OFF (POWER button ON) ★ (Power cord (Power cord Power Main power Standby Name Pin No. Pin name Function Signal direction connected to...

This manual is also suitable for:

Pdp-424mvPdp-614mx

Table of Contents