Tv Functions; Initial Setup - Magnavox 42MD459B User Manual

These operations are accessible by remote control. Some may also be accessible by controls on the main unit.

Initial Setup

This section will guide you through the unit's initial setting which includes
selecting a language for your on-screen menu and autoprogram, which
automatically scans and memorizes viewable channels.
Before you begin:
Make sure the unit is connected to antenna or cable.
1
After making all the necessary connections,
press [POWER y y ] to turn on the unit.
• This operation may take a few moments.
2
Use [Cursor K / L ] to select the on-screen language
from the choices on the right side of the TV screen.
(English / Español / Français)
or
• "Initial Setup" menu on step 3 will be displayed in the
selected language after you press [OK].
3
Use [Cursor K / L ] to select "Antenna" for TV channels
or "Cable" for CATV channels, then press [OK].
or
• "Autoprogram" will begin.

TV Functions

Initial Setup Initial Setup
Select the language for setup display.
English
Elija el idioma de ajuste. Español
Sélectionner langue écran config. Français
MENU
Select OK Skip
OK
Initial Setup
Initial Setup
Make sure the antenna is connected to ''ANT. IN'' jack.
Antenna
Select your signal source.
Cable
Skip
Antenna
Cable Or
ANT.IN
BACK MENU
Select OK Back Skip
OK
Initial Setup
Initial Setup
Now the system is scanning for channels, please wait.
Auto programming will take up to 20 minutes to complete.
0%
Analog channels 0ch
Digital channels 0ch
MENU
Skip
4
Use [Cursor s / B] to select the desired location setting,
then press [OK].
or
• Select "Retail", the unit will be set up with predefined
setting for retail displays. In this setting, the power
consumption may possibly exceed the limited
requirement of the ENERGY STAR® qualification.
• Select "Home", the unit is set to maximize the energy
efficiency for home setting and it can be adjusted
through a choice of picture and sound quality
according to your preference.
• When the initial setup is completed, the lowest
memorized channel with the confirmation message
of the location setting will be displayed on the TV
screen.
Note:
• If you connect the cable system directly, contact the CATV
installer.
• If you press [POWER y y ] or [MENU / EXIT] during
autoprogram, this setting will be canceled.
• The initial autoprogram function can be executed for either
"Antenna" or "Cable" only once. When you change the
connection (Antenna / Cable), set autoprogram again.
(Refer to page 22.)
• If there is no signal input from the antenna terminal and
no operation for several seconds after you turn on the unit,
"Helpful Hints" appears. Follow the instructions listed on the
TV screen.
Initial Setup Initial Setup
No channel is registered.
Try Autoprogram again?
Verify that you have a cable connected to the "ANT. IN" jack on the
back panel of the TV, the cannel installation process searches this
connection. If you are using a cable or satellite box please confirm
the input to which you have connected the box and use "SOURCE"
key on the remote control to tune to the appropriate source input.
Select
• You must set "Home" in step 4. Otherwise, the settings
of picture and sound quality you adjusted will not be
memorized after you turn off the unit.
After an initial setup is completed...
• If you want to scan the channels automatically again,
refer to "Autoprogram" on page 22.
• You can add the desired channels unmemorized by
"Autoprogram". Refer to "Add Channels" on page 23.
• If you want to change to another language, refer to
"Language Selection" on page 24.
• If you want to change the location setting, refer to
"Location" on page 35.
Initial Setup Initial Setup
Select "Retail" or "Home" for your location.
Retail Home
Select OK OK
Retry
Later
MENU
OK OK Skip
17
EN