Table of Contents
Advertisement
Operation Guide 3210
Bluetooth Connection
This watch supports connection and communication with a Bluetooth enabled device.
Before using the communication for the fi rst time, you need to fi rst pair the connection.
To pair a connection with a Bluetooth enabled device
1.
Situate the watch and the mobile phone so they are within the distance required for
Bluetooth communication.
2.
Put the mobile phone into discoverable mode.
Note
For details about the operation you need to perform during pairing, see the user
documentation that comes with your cell phone.
3.
On the watch, enter the Timekeeping Mode and then
hold down B for at least two seconds.
The watch will beep and then automatically start
looking for the phone.
To interrupt the operation part way through, press the
watch's B button.
E-10
Disconnecting and Reconnecting with a Bluetooth Enabled Device
(Mobile Phone)
B for at least two seconds.
1.
In the Timekeeping Mode, hold down
This will cause the operation tone to sound and toggle the connection between
on and off.
OFF
ON
The Bluetooth indicator is displayed while the connection setting is ON.
E-12
Using the Communication Functions
Incoming Mobile Phone Call
1.
The watch will perform the operations described below when an incoming call is
received on the mobile phone.
Beep and vibrate to alert the wearer of the call.
Display an incoming call icon, and then dhow the caller's name or number.
Note
When incoming animation is enabled, the incoming animation is played following
display of the incoming call icon.
E-14
Incoming Mail
1.
The watch will perform the operations described below when mail is received on
the mobile phone.
Beep and vibrate to alert the wearer of the mail.
Display an incoming mail icon, and then show the sender's name, address, or
number.
E-16
Other Incoming Information Operations
The watch performs the same operations as those for received calls and mail when
other information is received.
Incoming Emergency
Incoming News
Information
An incoming info operation can be stopped using the same procedure as that for
incoming calls and incoming mail.
E-18
Note
If one minute elapses and the watch is still unable to pair with the phone that was put
into discoverable mode, it will switch to the Timekeeping Mode without displaying the
Bluetooth icon. If this happens, restart the above procedure from step 1.
Note
Bluetooth indicator
ON
OFF
Note
Note
When incoming animation is enabled, the incoming animation is played following
display of the incoming call icon.
2.
Sounding the Mobile Phone Ringtone
You can sound the mobile phone ringtone by performing an operation on the watch.
You can also force sounding of the ringtone even when the mobile phone is in the
manner mode, which comes in handy when you are looking for your mobile phone.
Incoming Simple Alert/
Schedule Info
4.
When pairing is complete, the watch displays a
Bluetooth icon and switches to the Timekeeping Mode.
If the watch is unable to fi nd a device to pair with or
if the connection is interrupted, the watch display
changes a shown below. After about one minute, the
watch switches to the Timekeeping Mode.
The display shown below appears if the watch is
unable to fi nd a valid service. The watch will switch
to the Timekeeping Mode if your press any button
or if two or three minutes pass without any button
operation.
Connection is automatically canceled whenever the distance between the watch
and mobile phone exceeds 10 meters. However, the watch automatically attempts
to reconnect every 10 minutes for 60 minutes. If the two devices are brought in
communication distance during that time, they will be reconnected.
Activation of power saving will automatically switch connection to OFF and enter the
sleep state. The connection will be re-established when the watch exits the sleep
state.
2.
Pressing any one of the watch buttons or tapping the
center of the watch display twice with your fi ngertip will
stop the paging operation on the mobile phone and the
watch.
The watch will switch to the Timekeeping Mode.
The screen shown below will appear if you display the
missed calls screen.
Pressing a watch button or tapping the display to stop a paging operation does not
affect the mobile phone's connection to the call. If you want to answer the call or put
it on hold, you need to do so performing the required mobile phone operation.
An incoming call alert is not performed while the watch is in the sleep state.
The type of mail received can be determined by the header icon.
Header Icon
Mail Type
[E]
Email
[S]
SMS
[V]
Voice mail
[I]
Instant Message
Pressing any one of the watch buttons or tapping the center of the watch display
twice with your fi ngertip will stop the incoming call operation on the mobile phone
and the watch.
The watch will switch to the Timekeeping Mode.
1.
In the Timekeeping Mode, press
The screen shown below appears and the mobile
phone's ringtone sounds for about 10 seconds.
2.
Tapping the center of the watch display twice with your
fi ngertip while [TAP] is displayed (for about 15 seconds)
will stop the ringtone.
Note that you will be able to stop the ringtone by
tapping only while [TAP] is displayed. After [TAP]
disappears, you will need to perform the require mobile
phone operation to stop the ringtone.
E-11
E-13
E-15
E-17
D.
E-19
Advertisement
Table of Contents
