Troubleshooting This chapter provides information for troubleshooting problems on the Cisco ASR 903 Router. • BITS Port Pinout, page 1 • GPS Port Pinout, page 2 • Time of Day Port Pinout, page 3 • Alarm Port Pinout, page 4 •...
The table below summarizes the TOD pinout for A900-RSP2A and A900-RSP3-3C-400 modules. This port requires the use of SHIELDED cable for GR-1089-core “Intra-Bldg lightning surge” protection. Note RS422 interface is per industry standard EIA-422 /RS422 specification. Cisco ASR 903 Aggregation Services Router Hardware Installation Guide...
Clear to send 16 T1/E1 Interface Module Pinout The table below summarizes the pinouts of the cable (Tyco part number 2163442-1, Cisco part number 72-5184-01) used to connect the T1/E1 interface module to the rear of the patch panel. Table 8: 16 T1/E1 Interface Pinouts...
Page 6
R X _ R I N G _ P 1 4 TX_TIP_P14 RX_TIP_P14 Line 14 T X _ R I N G _ P 1 5 R X _ R I N G _ P 1 5 TX_TIP_P15 RX_TIP_P15 Cisco ASR 903 Aggregation Services Router Hardware Installation Guide...
Page 7
Figure 1: Wiring Schematic of Cable between 16 T1/E1 Interface and Patch Panel 32 T1/E1 Interface Module Pinout The table below summarizes the pinouts of the cable used to connect the 32 T1/E1 interface module to the rear of the patch panel. Cisco ASR 903 Aggregation Services Router Hardware Installation Guide...
Page 8
T X _ R I N G _ P 1 0 R X _ R I N G _ P 1 0 0-15 TX_TIP_P10 R X _ T I P _ P 1 0 Cisco ASR 903 Aggregation Services Router Hardware Installation Guide...
Page 9
T X _ R I N G _ P 2 1 R X _ R I N G _ P 2 1 16-31 TX_TIP_P21 R X _ T I P _ P 2 1 Cisco ASR 903 Aggregation Services Router Hardware Installation Guide...
Page 10
T X _ R I N G _ P 3 1 R X _ R I N G _ P 3 1 16-31 TX_TIP_P31 R X _ T I P _ P 3 1 Cisco ASR 903 Aggregation Services Router Hardware Installation Guide...
Not Connected Not Connected Not Connected Serial Cable Pinouts The following sections summarize the pinouts for 14-port serial interface module when used with the cable types specified in Connecting Serial Cables. Cisco ASR 903 Aggregation Services Router Hardware Installation Guide...
Page 12
The table below summarizes the pinouts for each serial interface type when using an RJ-45 connector. Table 12: RJ45 Pinout Standard DB-9 Direction Description RS-485 IRIG-B Input Ready to send RxD+ (RS485) Input RxD- (RS485) Input Transmit Cisco ASR 903 Aggregation Services Router Hardware Installation Guide...
Page 13
T I P _ A U D I O _ I N _ O U T Tip, audio input/output or output TIP_AUDIO_IN Tip, audio input Not used in 2-wire mode E_SIG_OUT Signaling output Cisco ASR 903 Aggregation Services Router Hardware Installation Guide...
Type-A to Type-A connector instead of a standard USB cable. The use of the USB console is mutually exclusive with the RS232 console/Aux port. While a USB cable Note is inserted, access is automatically switched to this port. Cisco ASR 903 Aggregation Services Router Hardware Installation Guide...
Data - Data + Ground Note USB TYPE-A receptacle used. The USB flash/MEM port +5VDC is output. We provide power for USB flash/MEM, and it operates as Note a USB host device. Cisco ASR 903 Aggregation Services Router Hardware Installation Guide...
A major alarm condition indicates the failure of a single fan in the fan tray; a critical alarm indicates the Note failure of multiple fans. In the event that a single fan fails, the Cisco ASR 903 Router software adjusts the fan speed to prevent excessive heat within the chassis.
Page 17
Yellow Free run Flashing yellow Holdover Green Locked to source USB flash (MEM) Flashing green USB activity BITS Out of service/not configured Amber Fault or loop condition Green In frame/working properly Cisco ASR 903 Aggregation Services Router Hardware Installation Guide...
Page 18
Green IOS is successfully IOS writes into FPGA booted register to indicate that it has booted, FPGA stops flashing PWR LED and turns Green. Software now controls the STAT LED. Cisco ASR 903 Aggregation Services Router Hardware Installation Guide...
Ok with activity or no activity Speed (S) Inactive port status Green Activity or no activity OC-3 and OC-192 Interface Module LEDs The table below summarizes the LEDs for the OC-3 and OC-192 interface module. Cisco ASR 903 Aggregation Services Router Hardware Installation Guide...
Page 20
The table below summarizes the LEDs for the 16-port T1/E1 interface module. Table 21: 16-port T1/E1 Interface Module LEDs Color/State Description (two LEDs for eachT1/E1 port) Active Green Active Blinking green Standby Operationally down; card is disabled or shut down Cisco ASR 903 Aggregation Services Router Hardware Installation Guide...
Page 21
The table below summarizes the LEDs for the 8-port T1/E1 interface module. Table 22: 8-port T1/E1 Interface Module LEDs Color/State Description (two LEDs for eachT1/E1 port) Active Green Active Blinking green Standby Operationally down; card is disabled or shut down Cisco ASR 903 Aggregation Services Router Hardware Installation Guide...
Page 22
The table below summarizes the LEDs for the 32-port T1/E1 interface module. Table 23: 32-port T1/E1 Interface Module LEDs Color/State Description (two LEDs for eachT1/E1 port) Active Green Active Blinking green Standby Operationally down; card is disabled or shut down Cisco ASR 903 Aggregation Services Router Hardware Installation Guide...
Page 23
Table 24: 48-port T1/E1 and 48-port T3/E3 interface Module LEDs Color/State Description (two LEDs for eachT1/E1 port) Active Green Active Blinking green Standby Operationally down; card is disabled or shut down Cisco ASR 903 Aggregation Services Router Hardware Installation Guide...
Blinking red Booting Green Active Serial Interface Module LEDs The table below summarizes the LEDs for the serial interface module. Table 25: Cisco ASR 903 Router Serial IM LEDs LED Label Color/State Meaning Power (PWR) Green All power rails are within spec.
Page 25
Port has failed Not Enabled (at POR) E and M Interface Module LEDs The table below summarizes the LEDs for the E & M interface module. Table 26: Cisco ASR 903 Router EandM IM LEDs LED Label Color/State Description Power (PWR) Green All power rails are within spec.
Page 26
Call not established Blinking Yellow Not used Initialized 4-Port C37.94 Interface Module LEDs The table below summarizes the LEDs for the 37.94 interface module. Table 27: Cisco ASR 903 Router C37.94 IM LEDs LED Label Color/State Description Power (PWR) Green All power rails are within spec.
Green Operational Table 29: DC Power Supply LEDs (A900-PWR-1200-D) Color/State Description Input OK No Input Voltage Amber Input voltage out of range Green Input voltage within acceptable operating range Cisco ASR 903 Aggregation Services Router Hardware Installation Guide...
Power supply fault (internal failure) Green Operational Fan Tray LEDs The table below summarizes the fan tray LEDs. Table 31: Fan Tray LEDs Color/State Description Status (TEMP) Disabled/power down Amber Over temperature Green Cisco ASR 903 Aggregation Services Router Hardware Installation Guide...
Critical (CRIT) No critical alarm Critical alarm (defaults to ON upon RSP reset) Alarm Conditions The table below summarizes the meaning of alarm conditions on the Cisco ASR 903 Router. Table 32: Alarm Condition Summary Alarm Type Alarm Description Critical...
Page 30
Troubleshooting Alarm Conditions Alarm Type Alarm Description Info Port administratively shut down Cisco ASR 903 Aggregation Services Router Hardware Installation Guide...