Page 2
LBH-H/O-EAD-R-ICP User Manual Link Bridge HBaseT/HDMI Receiver System w/External Audio and Inline Control Processor SAFETY INSTRUCTIONS AND COMPLIANCE DECLARATIONS PLEASE OBSERVE THE FOLLOWING SAFETY PRECAUTIONS SURGE PROTECTION DEVICE RECOMMENDED This product contains sensitive electrical components that may be damaged by electrical spikes, surges, electric shock, lightning strikes, etc.
LBH-H/O-EAD-R-ICP User Manual Link Bridge HBaseT/HDMI Receiver System w/External Audio and Inline Control Processor 1.0 PRODUCT DESCRIPTION Overall • A selectable HDBT or HDMI receiver with multiple control I/O ports • Provides in-line control I/O paths Receiver • Receive HDMI, audio, IR, and RS-232 up to 100 meters over 1 CAT-5e/6 cable •...
LBH-H/O-EAD-RX-ICP HDMI IN HDMI OUT Rear +24VDC 1.25 A RESET LINK CONFIG 1. Power/Link: The red LED indicates the unit is powered up. The green LED indicates that the unit has a good HDBT connection. Broadata Technical Support, (800) 214-0222...
LBH-H/O-EAD-R-ICP User Manual Link Bridge HBaseT/HDMI Receiver System w/External Audio and Inline Control Processor 2. HDCP LED: The blue LED is lighted when HDCP video is present. The blue LED blinks when non-HDCP video is present. 3. SPDIF LED: Lighted when corresponding SPDIF audio is active.
3.0 CONNECTOR PINOUT ASSIGNMENT 3.1 Extender 3.1.1 Serial Data Interface Each LBH-H/O-EAD-R-ICP unit can be used for RS-232 and IR interface. RS-232/ IR Data The LBH-H/O-EAD-R-ICP transmits two channels of data signals. Follow the procedures for installing data terminal devices.
LBH-H/O-EAD-R-ICP User Manual Link Bridge HBaseT/HDMI Receiver System w/External Audio and Inline Control Processor 2. Connect the other end of this cable to the front panel data terminal block connector on the LBH-H/O-EAD-R-ICP (see below). RS-232/IR Terminal block pinout 3.1.2 Status LED’s Additional status LED’s are provided for the user to indicate...
LBH-H/O-EAD-R-ICP User Manual Link Bridge HBaseT/HDMI Receiver System w/External Audio and Inline Control Processor 3.2 LB-ICP Front Broadata Technical Support, (800) 214-0222...
LBH-H/O-EAD-R-ICP User Manual Link Bridge HBaseT/HDMI Receiver System w/External Audio and Inline Control Processor IR detector IR OUT for behind holes external emitter Rear Reset button: push to reset to default settings RJ-45 DIP SW CONFIG/Keypad IR Learn LED 1 - TX+ Position 1: Local/Remote 1.
Page 11
The cable connection between LB-KP8 and LB-ICP is shown below. 1. White/Orange +12VDC IR Out Learner 2. Orange 3. White/Green 4. Blue CONFIG RESET 5. White/Blue 6. Green 7. White/Brown 8. Brown Standard RJ45 Termination T-568B Broadata Technical Support, (800) 214-0222...
LBH-H/O-EAD-R-ICP User Manual Link Bridge HBaseT/HDMI Receiver System w/External Audio and Inline Control Processor 4.0 LB-ICP WEB SERVER DESCRIPTION Introduction The ICP Web Server provides user friendly and intuitive web pages to configure the virtual keypad and automation functions within the ICP. It also provides web pages to manage the IR Learner and IR code import.
Page 13
See the following section for Configure System page details. Once logged in, the user is free to open any of the Configure or Settings pages. The default Password can be changed using the BCI Product Configuration program. Broadata Technical Support, (800) 214-0222...
Page 14
LBH-H/O-EAD-R-ICP User Manual Link Bridge HBaseT/HDMI Receiver System w/External Audio and Inline Control Processor Configure System The Configure System page is used to configure the network keypad, virtual keypad, RS-232 channels, Digital IO channels and remote unit types. On the top menu bar, click Configure and then click System. The following page will be displayed.
Page 15
Channel: Select channel 1, 2, 3 (Local Pass-through) or 3 (Remote Pass-through). Channel 1/2: RS-232 control channels. Channel 3 (Local Pass-through): RS-232 pass-through or control channel. This channel defaults as a control channel. See Pass-through Channel below to change to pass-through channel. Broadata Technical Support, (800) 214-0222...
Page 16
LBH-H/O-EAD-R-ICP User Manual Link Bridge HBaseT/HDMI Receiver System w/External Audio and Inline Control Processor Channel 3 (Remote pass-through): RS-232 pass-through channel on the remote unit. Note: This channel is not available if the remote unit is the LBx-H/DP-EAD-T. Baud Rate: Select a baud rate from 9600 to 115200 baud.
Page 17
Digital IOs are configured as outputs in the Configure System page.. On the top menu click Configure and then click Key Action. The following page will be displayed. Function Key: Select the function key F1 through F8 to be defined. Broadata Technical Support, (800) 214-0222...
Page 18
LBH-H/O-EAD-R-ICP User Manual Link Bridge HBaseT/HDMI Receiver System w/External Audio and Inline Control Processor Function Key Label: Type in a label name for the selected function key. Function Key Mode: Select Standard for a “momentary” type key. Only one action is assigned to a Standard key. Select Toggle for a “toggle”...
Page 19
Digital Output Channel: Select the digital output channel 1 or 2. Note: this option is not available if both Digital IO channels are set to Inputs in Configure System page. Digital Output State: Select the digital output state: 1 (High) or 0 (Low). Broadata Technical Support, (800) 214-0222...
Page 20
LBH-H/O-EAD-R-ICP User Manual Link Bridge HBaseT/HDMI Receiver System w/External Audio and Inline Control Processor RS-232 Options RS-232 Channel: Select channel 1, 2, or 3 (Remote). Transmit String: Type in the text string to be transmitted. Strings are terminated with CR, CR+LF or no termination, depending on the selection made in Configure System page.
Page 21
HBaseT/HDMI Receiver System w/External Audio and Inline Control Processor IR Options IR Preset: Select from list of IR commands stored in memory. IR commands must be learned via Configure IR Code page or imported via Configure IR Import page. Broadata Technical Support, (800) 214-0222...
Page 22
LBH-H/O-EAD-R-ICP User Manual Link Bridge HBaseT/HDMI Receiver System w/External Audio and Inline Control Processor Telnet Options Telnet ID: Select the telnet connection desired for telnet actions. The connections defined in Configure Telnet Connections page appear in this menu. Commands: Enter the command strings to be transmitted. Up to 4 different command strings can be defined.
Page 23
HDMI input. HDMI (local): Select local HDMI video input. Auto mode is disabled. HDMI (remote): Select remote HDMI video input. Auto mode is disabled. DisplayPort (remote): Select remote DisplayPort video input. Auto mode is disabled. Broadata Technical Support, (800) 214-0222...
Page 24
LBH-H/O-EAD-R-ICP User Manual Link Bridge HBaseT/HDMI Receiver System w/External Audio and Inline Control Processor Keypad Action Action: Select Press, Release, Press (no actions), Release (No actions) or Release All Toggle Buttons Press: This action presses the key selected in Key Number menu. All associated actions for the key press state will be executed.
Page 25
Telnet trigger. Note: A telnet trigger needs to be associated with one or more telnet actions. The check box under the Commands box in Configure Key Action, Telnet Options panel must be selected. Broadata Technical Support, (800) 214-0222...
Page 26
LBH-H/O-EAD-R-ICP User Manual Link Bridge HBaseT/HDMI Receiver System w/External Audio and Inline Control Processor Allow delayed actions checkbox: Select this box to allow a set of delayed actions to be overridden by the opposing trigger. For example: video detect asserted trigger overrides video detect de-asserted trigger actions.
Page 27
On the top menu click Configure and then click IR Code Import. The following page will be displayed: New Label: Enter a label for the IR code. Pronto Code: Enter the pronto code to be imported. Broadata Technical Support, (800) 214-0222...
Page 28
LBH-H/O-EAD-R-ICP User Manual Link Bridge HBaseT/HDMI Receiver System w/External Audio and Inline Control Processor Configure Telnet Connections The Configure Telnet Connections page is used to setup the telnet connections for telnet key actions and auto actions. There are 2 telnet connection types: Persistent and Action.
Page 29
Telnet Trigger 1 or Telnet Trigger 2 used in Auto Actions. Tx Spacing: Enter the delay (seconds) before command is transmitted in Telnet Actions. Enter 0 if no delay is desired. Broadata Technical Support, (800) 214-0222...
Page 30
LBH-H/O-EAD-R-ICP User Manual Link Bridge HBaseT/HDMI Receiver System w/External Audio and Inline Control Processor Configure Combination Triggers The Configure Combination Triggers page is used to define up to 2 different combination triggers. Each combination trigger supports the logical OR or AND function of up to 3 digital input or video detect trigger events.
Page 31
ICP settings are saved to a file on the local PC using the Save Settings button. ICP settings are restored from a file using the Restore Settings button. On the top menu click Settings and then click View and Manage Settings. The following page will be displayed: Broadata Technical Support, (800) 214-0222...
Page 32
LBH-H/O-EAD-R-ICP User Manual Link Bridge HBaseT/HDMI Receiver System w/External Audio and Inline Control Processor Click the Key Action Definitions Details button and the following will be displayed: Broadata Technical Support, Sales@Broadatacom.com...
Page 33
LBH-H/O-EAD-R-ICP User Manual Link Bridge HBaseT/HDMI Receiver System w/External Audio and Inline Control Processor Click the Auto Action Definitions Details button and the following will be displayed: Broadata Technical Support, (800) 214-0222...
Page 34
LBH-H/O-EAD-R-ICP User Manual Link Bridge HBaseT/HDMI Receiver System w/External Audio and Inline Control Processor Click the IR Code Definitions Details button and the following will be displayed: Broadata Technical Support, Sales@Broadatacom.com...
Page 35
LBH-H/O-EAD-R-ICP User Manual Link Bridge HBaseT/HDMI Receiver System w/External Audio and Inline Control Processor Click the Telnet Definitions Details button and the following will be displayed: Broadata Technical Support, (800) 214-0222...
Page 36
LBH-H/O-EAD-R-ICP User Manual Link Bridge HBaseT/HDMI Receiver System w/External Audio and Inline Control Processor Click the Combination Triggers Details button and the following will be displayed: Broadata Technical Support, Sales@Broadatacom.com...
Page 37
Relay channel 1. On the top menu click Configure and then Key Action. Configure F1 Key toggle-press action, to turn Relay channel 1 On as follows: Click Submit Changes. Broadata Technical Support, (800) 214-0222...
Page 38
LBH-H/O-EAD-R-ICP User Manual Link Bridge HBaseT/HDMI Receiver System w/External Audio and Inline Control Processor Configure F1 Key toggle-release action, to turn Relay channel 1 Off as follows: Click Submit Changes. On the top menu click Keypad. The following virtual keypad should be displayed: Broadata Technical Support, Sales@Broadatacom.com...
CAT-5e/6 or higher Number of Cables Connector/Distance RJ-45/Up to 100m ETHERNET (CONTROL) Channel Capacity Connector Female RJ-45 (integrated Activity and Link LEDs) Data Rate 10/100Base-T, half/full duplex with autodetect Protocols DHCP, HTTP, TCP/IP, UDP/IP, AUTOIP, Telnet Broadata Technical Support, (800) 214-0222...
Page 40
LBH-H/O-EAD-R-ICP User Manual Link Bridge HBaseT/HDMI Receiver System w/External Audio and Inline Control Processor RS-232 (CONTROL) Channel Capacity 2 (no flow control) or 1 (with RTS/ CTS flow control) Baud Rate 2400 to 115200 baud (9600 baud=default), 8 data bits, 1 stop bit,...
Page 41
HBaseT/HDMI Receiver System w/External Audio and Inline Control Processor PHYSICAL Dimensions 8.36” (W) x 4.23” (D) x 1.12” (H) Power Consumption 24 VDC @ 1.25A Operating Temperature 0 to 40-deg C Humidity 0 to 95%, non-condensing Broadata Technical Support, (800) 214-0222...
U.S. Please call Customer Service at 800-214-0222 for information. 6.2 Return/Repair Service The Link Bridge LBH-H/O-EAD-R-ICP System contains no user serviceable components. If you have a problem with your unit, please contact the Customer Service Department. To facilitate our return/repair processing please contact Broadata Communications, Inc.
HBaseT/HDMI Receiver System w/External Audio and Inline Control Processor 7.0 LIMITED WARRANTY Broadata Communications, Inc. (BCI) warrants, for a period of one year from date of shipment, each product sold shall be free from defects in material and workmanship. BCI will correct, either by repair, or at BCI’s election, by replacement, any said products that in our sole...
Page 44
LBH-H/O-EAD-R-ICP User Manual Link Bridge HBaseT/HDMI Receiver System w/External Audio and Inline Control Processor Broadata Technical Support, Sales@Broadatacom.com...
Page 45
LBH-H/O-EAD-R-ICP User Manual Link Bridge HBaseT/HDMI Receiver System w/External Audio and Inline Control Processor Broadata Technical Support, (800) 214-0222...
Page 46
LBH-H/O-EAD-R-ICP User Manual Link Bridge HBaseT/HDMI Receiver System w/External Audio and Inline Control Processor Broadata Technical Support, Sales@Broadatacom.com...
Page 47
Broadata Communications, Inc. 2545 West 237th Street, Suite K Torrance, CA 90505 1-800-214-0222 (310) 530-1416 (310) 530-5958 (Facsimile) e-mail: CustomerService@Broadatacom.com Website: www.broadatacom.com 60000-LBHHOEADRICPv2.20...