Advertisement
4.8.3
VERIFYING PART PROCRAM TAPE
4.8 TAPE VERIFYING
(1)
Verifying
a
part
program
tape
having
pro¬
gram
number
The punched tape may be compared
to
the
con¬
tents
of
the NC internal memory
to
check if they
match.
Part
program
-
Tool
offset data
Setting
data and
parameter
The punched
tape
is
entered
through
the
NC
tape
reader
or
the data
input/output
interface
(option)
For the
methods
of setting
the input/
output equipment
(setting
#6003)
and the baud
rate
(parameters #6026 through
#6029)
,
refer
to
4
9
DATA
INPUT/OUTPUT
INTERFACE.
The
following description
is
made
assuming
that this
option
is
installed
Select the EDIT
mode.
a.
Depress the PROG function
key.
b.
Set
the
part
program
tape
to
the tape reader.
c
.
d. Depress the
RESET
key.
Depress
the
V ER
key.
e
started
to
compare the
con-
The tape
is
tents
of the part
program
memory to the
contents
of the part program tape.
During
this
operation,
"VER"
blinks. If
a
mismatch
is
found,
"INPUT
ERROR"
is
displayed blinks
on
the CRT.
4.8.1
SETTING AND PARAMETER TAPE VERIFY
When
a
match
is
found
and this operation
is
completed,
the tape reader stops,
upon
which "VER" display
is
erased.
INC
Select
"1"
of system No
switch.
1
.
By the operation of "RESET, VER,"
Note
the
verifying
feature verifies the data from
the tape head
to
% code
2
Set
the
MODE SELECT switch to the EDIT.
Depress
PRM function
key.
3.
(2)
•4
Depress
RESET
key
Verifying
a
part
program
tape
having
no
program number
Load the
NC
tape
via
tape
reader
5.
Select the
EDIT
mode
a
.
6.
Depress VER key.
Tape
starts,
and the
contents
of tape
and
the
contents
of
setting
/parameter
are
veri¬
fied.
"VER"
is
blinks
on
the CRT.
If disagreement with the tape data
is
detect¬
ed,
"INPUT ERROR" blinks
on
the CRT.
Depress the PROG
function key.
b.
Set
the part
program
to
the
tape
reader.
c
.
Depress the RESET
key.
d.
Depress
the
"O"
key and key
in
program
number
Depress
VER key.
The tape starts
to
compare the con¬
tents of
the part
program memory
to
the
con¬
tents of the part program tape. During
this operation,
"VER" keeps blinking.
If
a
mismatch is
found,
"INPUT ERROR"
is
blinks
on
the CRT. When
a
match
is
found and
this operation
is
completed, the
tape reader
stops, upon which
"VER" display
is erased.
If the
keyed
in
program number
is
not
found
in
the memory,
"NOT
FOUND!"
blinks.
In
this
case,
depress the CAN key
and
start
with the
operation
of
d,
e
.
After
completion of verifying without dis¬
agreement, tape reader
stops
and
"VER"
dis¬
appears.
7
f.
4.8.2
TOOL OFFSET VALUE TAPE VERIFYING
Set
the
MODE SELECT
switch
to
the EDIT.
Depress
OFS
function key.
2
3.
Depress RESET key.
Load the
source tape
via
tape
reader.
Depress VER key
Tape
starts,
and
the
contents
of
tape
and
the
contents
of tool offset values
are
verifi
ed. If disagreement wtth the tape data
is
detected,
"INPUT ERROR" blinks
on
the
CRT.
4.
5.
After
completion
of
verifying without dis¬
agreement, tape reader stops and "VER"
disappears.
6
—
34
—
Advertisement
