Advertisement
The tape reader stops each
time it
has read
"M02
,
"M30
;
,
"
or
"M99
,
.
"
b
M3U %
%
IM 2SA
G92 X03
U-
f.
PROGRAM NUMBER
Depress the
IN
key
again.
The tape reader
resumes to
read
the tape.
Repeat this operation until all
programs
are
loaded.
Storing a
program with program
numbers
changed
I
HOLD HERE
d.
Depress the
RESET
key.
(5)
Key
in
"O" and
PROGRAM
NUMBER.
e.
When
"O" key
is
depressed
and program
number
is
keyed
m
before
depressing
IN
key
as
described
in
(4) above,
the keyed
in
pro¬
gram
number
is
registered
in
preference
to
the program number
punched
on the
NC tape.
f. Depress the
IN
key.
The program number entered from the key
is
registered
in
preference
to
the program
number
punched
on the
tape.
At this
time,
the program number
on the
tape is
written
to
the part
program memory simply
as a
label.
M02
;,
M30
; or
M99
;
is
read and the
stor¬
ing
operation
is
completed
.
(6)
Loading programs continuously
Programs
existing
on
a
tape as shown
in
(4)
may be
loaded
continuously without
inter¬
ruption.
For this
purpose, depress "O,"
9,"
and
11
9"
before the first
depression of
the IN
key. The
tape
reader
stops
at
the
position
of
"%.
M
NOTE-
ii
_
ti
ii
9," "9,
II
n
If
a
program
is
stored with a
changed pro¬
gram number
as
described
above, the
pro¬
gram number punched
on
the tape
is
stored
in the part program memory
without change.
Consequently, to avoid the confusion
in
the
later handling, replace the
program
number
in
the part program memory
with
changed
program number by the
EDIT operation.
1.
4.5.2 MAKING
ADDITION
TO A PART PROGRAM
Perform
the
following
operation
to
add data
to a
part
program
which
is
already
loaded.
Select EDIT
mode.
a
.
(4)
Loading part programs from
a
tape
b. Depress the PROG
key
a.
Select
EDIT mode.
c.
Depress the
O
key then
enter
the part pro¬
gram
number and
depress
the
[Vj
key.
b.
Depress the PROG
key.
c.
Load the
NC
tape
to
the tape reader or
an
equivalent
external device.
The system searches the
designated program.
d. Load the tape of
adding
data
to the tape
reader.
S
MO?
0200
M
30 0500
M99
%
%o
1
oo
r
T
T
IS
M30
,
%
•
•
%;
Adding
data
The
tape
stops
to
travel here.
The
tape
stops
to
travel
here.
The
tape stops
to
travel here.
e.
Depress the RESET key.
f. Depress the
NEXT
and
IN
keys
in
this
order.
The data will
be read from
the tape
into
the
memory
.
d. Depress the
RESET
key.
e.
Depress the
IN
key.
Then the
system starts
to
read the tape
and enlists the program number
punched
on
the tape
as
the first record. The sys¬
tem
checks for
duplication
of program num¬
ber
as
described in
(2).
NOTE
the middle of
it.
If necessary,
delete
the
last
part
of the program
by
editing operation and
perform this adding.
You cannot
add data
to a
program from
-
25
—
Advertisement
