JAMO DVR 50 Service Manual
Hide thumbs Also See for DVR 50:

Advertisement

Jamo Service manual
This manual is intended for Jamo retailers and their appointed service representatives. Jamo assume that basic service procedures inherent to
the industry, and specifi cally Jamo products, are already known and understood by the users and will for that reason not be restated here.
WARNING
WARNING
IMPORTANT
IMPORTANT
IMPORTANT
Contents
To Service Personnel .......... 2 - 4
Specifi cations ........................... 5
Dvr 50 Diassembly ................. 6
System overview ......................7
Block diagram ..........................8

IMPORTANT NOTICE

Failure to follow appropriate service and safety procedures when servicing this product may result in personal injury,
destruction of expensive components and equipment or/and shortening the product life or/and failure of the product
to perform as specifi ed. For these reasons Jamo strongly advice product owners that all service required should be
performed by an authorized Jamo retailer or the appointed service representative.
Static discharge can destroy expensive components, equipment or/and shorten the product life. Discharge any static
electricity accumulated in your body or materials in the vicinity of the workplace by grounding.
This manual does not in its self constitute authorization, certifi cation or establish a principle agent or partner
relationship of any form.
Jamo continually strive to improve their products and as a consequence of these modifi cations are inevitable. Specifi cations
are subject to change without notice or obligation to retrofi t. Should any discrepancy appear in this manual, please
contact Jamo Call center.
Disconnect all mains power before disassembly or part replacement. Recheck all work before reapplying mains power to the unit.
Faultfi nding .................... 9
Audio board ................. 10
VFD board .................... 23
Mpeg Board ................ 25
Loader .......................... 54
DVR 50
HOME CINEMA SYSTEM
Remote control ................................ 56
Cabinet ...................................... 57 - 61
Cables ............................................... 62
Legend And Abbreviations .............. 63
DVR 50 - Rev. 011105-2
DVR 50
Rev. 011105-2
1

Advertisement

Table of Contents
loading

Summary of Contents for JAMO DVR 50

  • Page 1: Important Notice

    This manual is intended for Jamo retailers and their appointed service representatives. Jamo assume that basic service procedures inherent to the industry, and specifi cally Jamo products, are already known and understood by the users and will for that reason not be restated here.
  • Page 2 In case a measurement is outside the limits specifi ed, there is a risk of shock hazard, and the product should be repaired and rechecked before it is returned to the customer. These leakage current measurements are according to IEC 60065 and UL 6500. DVR 50 - Rev. 011105-2...
  • Page 3: Cabinet

    The outside of the product may be cleaned using a damp cloth with mild detergent. Never use abrasives or solvents like Methanol as these may damage the product. Excessive use of water may damage the cabinet, speaker units or cause electrical shock or short circuit. DVR 50 - Rev. 011105-2...
  • Page 4 DVR 50 Serial No.: On all DVR 50 units you will fi nd a Serial number on the rear panel. Fig. 44-0401/8 The number is made up of tree sections. The fi st section is the factory code (two digits). The next section is the revision number (two digits).
  • Page 5 TuningRange ........................87,5 - 108.0Mhz / 522 - 1611 kHz RadioSNRatio ..................................> 70dB DiscFormats .............CD/CD-R/CD-RW/DVD-Video/DVR-R/DVD-RW/DVD+R/DVD+RW/ VideoInputs ....................................No ProgressiveScan ..............................Yes, PAL/NTSC VideoOutputs ..................Composite, S-Video, RGB(Scart), Component PowerConsumption ..............................Max 120W AudioOutputs ..........................1x Analog/ 1x Optical Dig. DVR 50 - Rev. 011105-2...
  • Page 6 DVR 50 diassembly DVR 50 - Rev. 011105-2...
  • Page 7: Rear View

    DVR 50 System overview Top view High voltage Do not touch during operation! DVD Loader Tuner DVD receiver module EU/US PSU assy Audio DVR 50 Audio board VFD board MPEG board Rear view 15 16 17 18 19 9 10...
  • Page 8 DVR 50 Block diagram DVR 50 - Rev. 011105-2...
  • Page 9 Press LOAD to open the loader tray Press INFO followed by 2,7,6 and you have now accessed the hidden menu. Press MENU to close the hidden menu again. The latest Firmware (instructions included) can be downloaded from the Jamo website under download. Symptom Possible cause Correction The unit will not power up.
  • Page 10 Ref. No. Item No. PCS. 74101 PCB assy Audioboard DVR-50 Rev. ≥ 4 Replacing the DVR 50 Audio board • Disconnect the power cord from the AC outlet and take all necessary ESD precaution. • Remove the Lid. (See instruction under Lid) •...
  • Page 11 Sigma Connector Page 11 Power Supply Connector +3.3V +3.3V +12VR -12VR A_GND A_GND VCC5V LINEOUTL GNDR LINEOUTR /SPDIF_ERR_SENSE DIT_SPDIF Equalizer DSP Page 7 /A_RESET +3.3V OPT_SPDIF +3.3V DVD_SPDIF /ERR_RCVY COAX_SPDIF /MUTE /RESET AUX_L AUX_L AUX_R AUX_R VCR_L VCR_L /INT VCR_R Page 6 VCR_R /RESET...
  • Page 12: Z301

    U301 HEF4052B C303 R310 10uF/16V 150R R322 0R0 R309 C304 100K 10nF AUX_L R323 0R0 AUX_R R324 0R0 VCR_L R325 0R0 C305 R312 VCR_R R326 0R0 10uF/16V 150R TUN_L R327 0R0 R311 C306 TUN_R R328 0R0 100K 10nF TV_L R329 0R0 C315 100nF TV_R...
  • Page 13 L401 +3.3VD BEAD +3.3V C401 C402 100nF 10uF/16V C403 R402 /RESET 10uF/16V 560R LINEOUTL R403 R401 C404 DAC_DATA 1.5nF Q403 U401 CS4340 2N3904 MUTEC SDATA AOUTL C405 R405 DAC_SCLK SCLK/DEM 10uF/16V 560R LRCK AGND LINEOUTR MCLK AOUTR R406 DIF1 REF_GND R404 C406 DAC_LRCLK...
  • Page 14 U902B 74HC74 U901B 74HC00 R901 R902 R906 +3.3VA 220R HI_MCLK +3.3VD R908 X901 Not Mounted R907 U901A U901C Not Mounted C901 C902 CLK_SEL 10pF 10pF 74HC00 74HC00 U902A 74HC74 R905 MCLK U901D 74HC00 R903 R904 +3.3VD 220R X902 24.576 MHz C903 C904 10pF...
  • Page 15 +2.5VD R512 R514 R515 R516 R521 R522 EQ_MCLK GPIO10 EQ_SCLK /Audio EQ_LRCLK EQ_DATA1 EQ_DATA2 +3.3VD EQ_DATA3 R523 R529 R530 R513 DAC_MCLK +3.3VD DAC_LRCLK U501 DAC_DATA DAC_SCLK R501 R524 33R AUDATA2 GPIO10 GPIO7 GPIO6 U503A GPIO5 RESET GPIO4 AGND +2.5VD CS493264-CL +2.5VA DGND2 FILT1...
  • Page 16 R701 0R0 R702 0R0 R703 0R0 R704 0R0 R705 0R0 R706 0R0 U701 AMP_DATA1 EQ_DATA1 SDIN1 SDOUT1 EQ_DATA2 AMP_DATA2 SDIN2 SDOUT2 EQ_DATA3 SDIN3 SDOUT3 R707 AMP_DATA3 SDIN4 AMP_SCLK ORIN SCLKOUT1 R708 SCLKOUT2 EQ_MCLK AMP_MCLK MCLKI MCLKO EQ_SCLK SCLKIN EQ_LRCLK LRCLK AMP_LRCLK PWRDN /RESET...
  • Page 17: R801

    R801 +12VR +12V Z801 C801 AMS117 47uF/16V R802 -12VR -12V R803 301R C802 +3.3V 47uF/16V R804 C804 47uF/16V 510R VCC5V C803 47uF/16V Z802 AMS117 G NDR R805 G ND 301R +2.5V R806 C805 47uF/16V 301R Components having special characteristics or critical for safety are identifi...
  • Page 18 L101 +3.3V BEAD L102 BEAD L103 BEAD U102B C115 C116 10uF/16V 100nF C103 C102 C101 C104 C105 C106 100nF 10uF/16V 10uF/16V 100nF NC7SZ125M5 C107 C108 100nF R103 DIR_LRCLK R104 33R U101 C112 DIR_SCLK 10nF RXP3 OLRCK OPT_SPDIF RXP2 OSCLK DIR_DATA RXP1 SDOUT C113...
  • Page 19 L201 +3.3V BEAD L202 BEAD C203 C202 C201 C204 C205 C206 100nF 10uF/16V 10uF/16V 100nF U201 CS8405-CS COPY/C ORIG VL2+ DIT_SPDIF EMPH SFMT0 SFMT1 R209 Not Mounted DGND DGND DGND OMCK /RESET APMS AUDIO TCBLD DIT_LRCLK ILRCK ISCLK DIT_SCLK SDIN TCBL DIT_DATA R201...
  • Page 20 TUN_L L017 Audio Signal Connector L018 J001 LINEOUTL L028 LINEOUTR TUN_R L029 L019 TV_L L030 +3.3VD J002 L031 TV_R D001 BAV99 L032 VCR_L VCR_R L033 L020 L021 AUX_L L034 L022 AUX_R /SPDIF_ERR_SENSE L035 L023 L024 L036 L037 OPT_SPDIF HI_MCLK L025 +3.3VD COAX_SPDIF L038...
  • Page 21: Table Of Contents

    R401 R404 R408-409 R411 R413 R512 R517-519 Res., 5%, 0603, 10K ohm R1608 10K Philips Semicondutors R301-309 R311 Res., 5%, 0603, 100K ohm Res., 5%, 0603, 100K ohm ANYBODY FOLLOWING SPEC. R901 R903 Res., 5%, 0603, 1M ohm ANYBODY FOLLOWING SPEC. DVR 50 - Rev. 011105-2...
  • Page 22 705 L901-902 @100MHZ J1-3 Connector, SMD,24p,1.0MM Pitch, Angled 52207-2490 MOLEX INC. J1-3 Connector, SMD,24p,1.0MM Pitch, Angled 1224SM-24-40 Neltron Industrial Co., Ltd PCB, Audio DSP 953501103 EURO CIRCUIT CO., LTD Label PCB 40*8MM 8*40MM ANYBODY FOLLOWING SPEC. DVR 50 - Rev. 011105-2...
  • Page 23 PCS. Remarks 74102 VFD Board PCB assy DVR-50 Replacing the DVR 50 VFD board • Disconnect the power cord from the AC outlet and take all necessary ESD precaution. • Remove the Lid and Plastic front. (See instruction under these parts) •...
  • Page 24 Components having special characteristics or critical for safety are Schematic diagram is subject to change without notice. identifi ed by mark and must be replaced with components specifi ed by the manufacturer. Schematic diagram - VFD board 1/1...
  • Page 25 DVR 50 MPEG board Rev. 2 Remarks Ref. No. Item No. Part description PCS. 74104 PCB assy MPEG board DVR-50 Rev. ≥ 4 Replacing the DVR 50 MPEG board: DVR 50 - Rev. 011105-2...
  • Page 26 SCART Page Index Block Diagram/Notes HDTV OUT Power, FIP input, Reset EM8500 Main I/Os Component EM8500 Power and decoupling TV OUT 27MHz EM8500 Sys SDRAM + Flash S-video/ CVBS EM8500 MPEG SDRAM + UART IDE / DVD LOADER DownMix Video Out + Scart Video 96kHz RESET...
  • Page 27 Reset 1.8V Regulator Vcc3V3 Dual AMS1117 Adj Vcc5V Vcc1V8 U11B U11D RESET# R195 301 74HC04 74HC04 C2000 C2001 0.1uF 0.1uF R196 130 U11C IDE_RESET# HD R1x2 74HC04 U11E Vcc3V3 PIO_9 74HC04 U11F 3.3V Regulator Panel cn 74HC04 U11A DF3-6P-2H(20) HIROSE BEAD J_FIP_DIN C120...
  • Page 28 R333 Not Mounted I2CM_SDA I2C_SDA Vcc3V3 I2CM_SCK 24C0x I2C_SCL R334 Not Mounted R335 R336 VSYNC R601 I2CM_SCK H SYNC Vcc3V3 I2CM_SDA R602 TV_CVBS CVBS TV_Y/G/Y TV_U/B/CVBS H DR1x3 VIDEO OUT Not Mounted TV OUT TV_V/R/C Vcc3V3 PIO1_8 PIO1_7 ACLK1 I2CM_SCK SCOUT1 I2CM_SDA SDOUT1...
  • Page 29 Vcc1V8 U 1C Vcc3V3 V_DAC_3V3 Vcc3V3 AVDD_D_33 AVDD_C_33 AVVD_Y_33 AVDD_U_33 Use 200ohm if AVDD_V_33 single terminated VIDEO RSET DACs 0.1uF VREF AVSS_D VCC_3V3 CVBS_VSS VGND Vcc5V Vcc1V8 EM8500 RESET# RESET# Vcc3V3 PLL_ENABLE XOUT XOUT OSC. CLK_OUT 27MHz CLK_OUT JTAG_TCK 27pF 27pF CLK32K NTRST...
  • Page 30 SYS_MD[31:0] SYS_MD[31:0] SYS_MD31 Vcc3V3 Vcc3V3 MD_31 SYS_MD30 SYS_MA[20:0] MD_30 SYS_MA[20:0] SYS_MD29 MD_29 SYS_FL_CS# SYS_MD28 MD_28 SYS_MD27 SYS_MA0 SYS_MD0 MD_27 SYS_SD_WE# SYS_MD26 SYS_MA1 SYS_MD1 MD_26 SYS_MD25 SYS_MA0 SYS_MA2 SYS_MD2 MD_25 SYS_FL_WE# SYS_MD24 SYS_MA1 SYS_MD0 SYS_MA3 SYS_MD3 MD_24 SYS_MD23 SYS_MA2 SYS_MD1 SYS_MA4 MBM29LV320BM SYS_MD4 MD_23...
  • Page 31 MPG_SD_D[31:0] Vcc3V3 6-Ch Vcc3V3 MPG_SD_D31 Not Mounted 2-Ch MPG_SD_D30 RP25 SCART (Europe) MPG_SD_A[11:0] MPG_SD_D29 4x10K no DVI U 1D MPG_SD_D28 I2S OUT MPG_SD_D27 MPG_SD_D31 MPG_SD_A11 MPG_SD_D31 MM_DATA31 DQ31 MPG_SD_D26 RP23 MPG_SD_D30 MPG_SD_A10 MPG_SD_D30 MM_DATA30 DQ30 MPG_SD_D25 4x10K Reserved MPG_SD_D29 MPG_SD_A9 MPG_SD_D29 MM_DATA29 DQ29...
  • Page 32 IDE_RESET# IDE_PD[15..0] IDE_PD15 IDE_PD14 IDE_PD13 IDE_PD12 IDE_PD11 IDE CONNECTOR IDE_PD10 IDE_PD9 IDE_PD8 IDE_PD7 IDE_RESET# IDE_PD6 R105 IDE_PD7 IDE_PD7 IDE_PD8 IDE_PD5 IDE_PD6 IDE_PD9 IDE_PD4 IDE_PD5 IDE_PD10 IDE_PD3 IDE_PD4 IDE_PD11 IDE_PD2 IDE_PD3 IDE_PD12 IDE_PD1 Vcc3V3 IDE_PD2 IDE_PD13 IDE_PD0 IDE_PD1 IDE_PD14 IDE_PD0 IDE_PD15 IDE_PA[2..0] R106 IDE_DMARQ...
  • Page 33 CONFIDENTIAL Vcc12V Vcc12V Vcc5V Vcc5V U40B H S YNC VGAHS H S YNC SCART-CLK 2N3904 Vcc3V3 CLKOUT 74ACT125 U21A For VGA output SCT-169 U40A SCT-V8 74LCX125 SCART-V8 Vcc3V3 VSYNC VGAVS VSYNC SCART-DATA U21B SCT-V16 SCART-V16 SCT-ENB VGA-ENB DATA 74ACT125 74LCX125 2N3904 2N3904 Vcc3V3...
  • Page 34 ANALOG AUDIO OUT AUDIO-OUT-GND C306 R341 AUX-L-IN 100pF AUX-R-IN R352 Not Mounted VCR-L-IN VCR-R-IN TUNER-IN-L R342 4K7 U52A TUNER-IN-R LM833/SO R349 560 AUDIO-L AUDIO-L-OUT AUDIO-L-OUT BEAD C218 C217 AUDIO-OUT-GND R343 4K7 330pF AUDIO-R-OUT R344 4K7 R354 L110 RCA3x4 Not Mounted BEAD SCART-L-OUT C307 100pF...
  • Page 35 SCART-CLK BEAD 100pF C107 SCART-DATA BEAD 100pF C108 SCART-V8 BEAD 100pF SCART-V16 BEAD 100pF C101 CVBS IN SCART-CVBS BEAD CVBS 100pF CVBS GND BLNK SCART-R BEAD 100pF R GND DATA SCART-G BEAD CLKOUT 100pF G GND SWTCH Connect SCART Ground plane here! SCART-B BEAD Aud IN L...
  • Page 36 Vcc5V C125 10uF/16V C129 0.1uF C131 C135 0.1uF Vcc5V 0.1uF C132 C136 0.1uF Vcc5V 0.1uF SHTDN J_UART1_DTR U1_DTR J_UART1_DTR J_UART1_DTR J_UART1_RTS U1_RTS J_UART1_RTS J_UART1_RTS J_UART1_TXD U1_TXD J_UART1_TXD J_UART1_TXD J_UART1_RXD U1_RXD J_UART1_RXD J_UART1_RXD J_UART1_CTS U1_CTS J_UART1_CTS J_UART1_CTS J_UART1_DSR U1_DSR J_UART1_DSR J_UART1_DSR J_UART1_CD U1_CD J_UART1_CD...
  • Page 37 SYS_MD[31:0] Vcc3V3 74LVX245 FlexROM III SYS_MD8 FLEX_MD8 SYS_MD1 FLEX_MD1 SYS_MD0 FLEX_MD0 SYS_MD2 FLEX_MD2 SYS_MD3 FLEX_MD3 SYS_MD4 FLEX_MD4 SYS_MD6 FLEX_MD6 FLEX_SD_WE# FLEX_MA0 SYS_MD7 FLEX_MD7 FLEX_MD0 FLEX_MA1 FLEX_MD1 FLEX_MA2 FLEX_MD2 FLEX_MA3 FLEX_MD3 FLEX_MA4 FLEX_MD4 FLEX_MA5 FLEX_MD5 FLEX_MA6 Vcc3V3 FLEX_MD6 FLEX_MA7 74LVX245 FLEX_MD7 FLEX_MA8 SYS_MD15 FLEX_MD15...
  • Page 38 VCC3V3 PIO1_7 I2C_SDA BEAD Dual C185 C186 Not Mounted Not Mounted Neltron P/N VCC3V3 1224SM-24-30 PCB to VCC3V3 FFC/FPC VCC3V3 PIO1_8 Connector I2C_SCL BEAD Dual C187 C188 DSP1 SPDIFOUT BEAD Not Mounted Not Mounted R201 R202 R203 Dual C189 C190 100pF 100pF VCC3V3...
  • Page 39 Place these components close to J35 LFE Output VCR-L VCR-L-IN BEAD C211 C212 C213 C214 22nF 3.3nF 22pF 22pF Neltron P/N VCR Input 1224SM-24-30 PCB to VCR-R RCA1x1 Blue VCR-r-IN FFC/FPC C215 C216 Connector 22nF 3.3nF DSP2 L506 AUDIO-L AUDIO-L BEAD AUDIO-R L507 BEAD...
  • Page 40 R340 Vcc12V VCC3V3 PIO4 = Lo -> Tuner Control 74LCX125 PIO4 = Hi -> Read RDS & ST VCC3V3 VCC5V VCC5V U50A 2N3904 R357 C304 PIO_4 0.1uF R339 R207 U49B PIO_2 DSP3 C237 L101 0.1uF TUN_Ok TUN_CE BEAD TUN_ST To DSP 2N3904 Interface 1 Dual...
  • Page 41 STB3V3 EM8500_IR_input STB3V3 R211 Not Mounted U48C R212 74AC04 U48B U48A J_FIP_IR U48D STB3V3 74AC04 74AC04 STB3V3 STB3V3 74AC04 U48E R309 R310 Watchdog Timer J_FIP_CLKO 74AC04 PSU_STB MCLR U48F STB3V3 Dual R300 PIC16F630 74AC04 Not Mounted STB3V3 STB3V3 R301 C300 0.1uF Dual STB3V3...
  • Page 42: Sot223 Regulator Ams1117 800Ma Adjustable

    Diode, Dual, BAV99 FDSO1203 SOT-23 BAV99 Siemens AG D1-4 D12-24 D28 D32-43 Diode, Dual, BAV99 FDSO1203 SOT-23 D1-4 D12-24 D28 D32-43 Diode, Dual, BAV99 FDSO1203 SOT-23 BAV99 TEMIC D1-4 D12-24 D28 D32-43 Diode, Dual, BAV99 FDSO1203 SOT-23 DVR 50 - Rev. 011105-2...
  • Page 43: Res., 1%, 0603, 301 Ohm

    C211 C215 C221 C223 C225 C227 C230 Cap. Cer., 10%, 0603, 10nF, X7R, 50V ANYBODY FOLLOWING SPEC. C234 C211 C215 C221 C223 C225 C227 C230 Cap. Cer., 10%, 0603, 10nF, X7R, 50V C1608 103 Philips Semicondutors C234 DVR 50 - Rev. 011105-2...
  • Page 44 Connector, Lead 4*Stereo RCA, GOLD Pl OW8-8.4-13 White/Red, Gold pl. OLE WOLFF ELEKTRONIK A/S Connector, Lead 21pin Single Scart OW-101 OLE WOLFF ELEKTRONIK A/S DSP3 Connector, Lead,13p, 1.25MM Pitch, 2323S-13A Neltron Industrial Co., Ltd Straight DVR 50 - Rev. 011105-2...
  • Page 45 Tuner DVD Receiver Module “EU” DVR-50 Model KST - MV114MA1 - B0 74106 Tuner DVD Receiver Module “US” DVR-50 Model KST - MV011MA0 - B0 Replacing the DVR 50 Tuner: • Disconnect the power cord from the AC outlet and take all necessary ESD precaution.
  • Page 46 Of the same reason are the screwheads on these screw smaller than normal. Do not mix these screws as this may damage the PSU board. • Mount the new PSU Board and assemble the DVR 50 unit in the reverse order of disassembling it Fig. 44-0398/3 Fig. 44-0398/2 Caution High voltage! The PSU main heat sink is connected to the power supplies fl...
  • Page 47 Components having special characteristics or critical for safety are identifi ed by mark and must be replaced with components specifi ed by the manufacturer. Schematic diagram is subject to change without notice. Schematic diagram - PSU/AMP board 1/7...
  • Page 48 Components having special characteristics or critical for safety are identifi ed by mark and must be replaced with components specifi ed by the manufacturer. Schematic diagram is subject to change without notice. Schematic diagram - PSU/AMP board 2/7...
  • Page 49 Left Output Stage Left Front Speaker Output GATE-DRV-SUP PWM-OA-1 C203 C202 L240 R240 100nF 100nF 10uH C243 100nF C245 10nF J240 PWM-P-1 PVDDA-1 U200 TAS5110DAD C242 470nF PWM-M-1 PWM_BP PVDDB2 PWM_BM LDROUTB C205 R204 C ON2 /VALID-1 RESET BOOTSTRAPB 100nF 1 R5 C204 C246...
  • Page 50 Left Surround Output Stage Left Surround Speaker Output GATE-DRV-SUP PWM-OA-3 C303 C302 L340 R340 100nF 100nF 10uH C343 100nF C345 10nF J340 PWM-P-3 PVDDA-3 U300 TAS5110DAD C342 470nF PWM-M-3 PWM_BP PVDDB2 PWM_BM LDROUTB C305 R304 C ON2 /VALID-3 RESET BOOTSTRAPB 100nF 1 R5 C304...
  • Page 51 PWM-OA-5 GATE-DRV-SUP C403 C402 L440 R440 100nF 100nF 10uH C443 100nF C445 10nF J440 PWM-P-5 PVDDA-5 U400 TAS5110DAD C442 470nF PWM-M-5 PWM_BP PVDDB2 PWM_BM LDROUTB C405 R404 C ON2 /VALID-5 RESET BOOTSTRAPB 100nF 1 R5 C404 C446 PWDN PVDDB1 R400 33nF 10nF BIASB...
  • Page 52 +3.3V PWM-P-1 PWM-M-1 /VALID-1 PWM-P-2 PCB Layout note: PWM-M-2 Isolated groundplane (connected to GND through R004). Must be placed below R004, R006, C002, C003, C004, /VALID-2 C005 and U3 (pin 1 - 6 and pin 61 - 64). PWM-P-3 R005 PWM-M-3 Connect ground plane here /VALID-3...
  • Page 53 D N4 D N4 BAV99 BAV99 BAV99 BAV99 BAV99 BAV99 BAV99 BAV99 BAV99 BAV99 BAV99 MCLK SD IN1 SD IN2 SD IN3 SCLK LRCLK /MUTE /SD-E /RST LFE-OUT D SP Interface +12V -12V From PSU +12V Decoupling components at the start of the +25V power supply line Decoupling components at the end of the +25V power supply line.
  • Page 54 • Test the DVR 50 unit. NOTE ! On early DVR 50 units the loader can become stock on the loader cover when retracting. To correct the problems loosen the DVD loader screws and realign the loader. When realigned tighten and glue the screws again. All new units do not Fig.
  • Page 55 How to take of 1802 loader front panel DVR 50 - Rev. 011105-2...
  • Page 56 DVR 50 Remote control Ref. No. Item No. Part description PCS. Remarks 74122 Remote control DVR 50 Standart model DVR 50 - Rev. 011105-2...
  • Page 57 Ref. No. Item No. Part description PCS. Remarks 74107 Lid Gray DVR-50 Replacing the Lid Grey DVR 50 • Disconnect the power cord from the AC outlet and take all necessary ESD precaution. • Remove the Lid screws (7 screws in all) 44-0402/4/5 •...
  • Page 58 • Remove the PSU/Audio board assembly. • Build up (assemble) the DVR 50 on the new Chassis Sub. Assy. by mounting • Remove the MPEG board. See picture 44-0398/4 the boards in the reverse order of disassembling the DVR 50 units.
  • Page 59 DVR 50 Plastic front Replacing the DVR 50 Plastic front DVR 50 - Rev. 011105-2...
  • Page 60 Replace the rear panel with a new panel. • Re-mount all the screws on the rear panel. • Transfer the Serial number from the old rear panel. • Re-mount the Tuner. (See instruction under Tuner) • Test the DVR 50 unit. DVR 50 - Rev. 011105-2...
  • Page 61 Gently pull or slide the Plastic Part upwards. The Plastic Part should now come off with a click! Note! If the Plastic Part are missing or parts of it is missing make sure that it is not inside the DVR 50 unit. •...
  • Page 62 Cable, Harness 13P 60MM 1.25MM pitch type D DVR-50 Cable, Harness 24P (60MM) 1MM pitch type D DVR-50 74119 Cable, Harness 24P (102MM) 1MM pitch type D DVR-50 74120 Cable, Harness 24P (250MM) 1MM pitch type D DVR-50 74121 DVR 50 - Rev. 011105-2...
  • Page 63 There may be exceptions from this code. E.g. when using serial connection and coupled cavity. Cores and yokes for coils Powder core 51710 FE+aag Iron yoke at top 51730 FE+2aag Iron yoke at bottom and top 51730 (x 2) DVR 50 - Rev. 011105-2...

Table of Contents