Post Installation Procedures; Mechanical Checks; Connecting To A Radar Scanner Over Raynet; Powering On A Quantum Radar - Raymarine Quantum Radome Installation Instructions Manual

7.1 Post installation procedures

Before using the product, carry out the following:

• Mechanical checks.

• Switch on and initial setup.
Mechanical checks
Before switching on the product:
• Ensure that:
– All securing bolts are fully tightened and the
appropriate mechanical locking washers are in
place.
– All connections are securely made.
– All connecting cables and wires are secured and
protected as necessary.
• Ask your local Raymarine authorized installer to
check the installation.
Connecting to a Radar scanner over
RayNet
Once you've made all the relevant power and
data connections as described in the Cables
and connections section, you can use the Radar
application on a compatible display to conduct
further initial tests.
For detailed instructions on how to conduct the initial
tests, refer to the Radar application chapter of the
Operations handbook for your display.
Note: If you have a Wi-Fi-only variant Radar
scanner, refer to the Pairing with a Quantum
Radar using Wi-Fi section for information on
connecting to an MFD via Wi-Fi.

Powering on a Quantum Radar

With the radar scanner in a powered off state, and
connected to a compatible multifunction display
(MFD):
1. On the MFD, launch the Radar application.
A message box is displayed indicating that a
Radar scanner is off or "not connected".
2. Select On from the onscreen message box.
The Radar will power up in Standby mode.
3. Once the Radar has powered up, select Tx to
start the Radar transmitting.
Radar returns will now be displayed onscreen.
Pairing with a Quantum Radar using
Wi-Fi
If your Radar scanner supports a Wi-Fi connection,
you can connect to a LightHouse
supports Wi-Fi. During pairing, the Wi-Fi credentials
of all MFDs with Wi-Fi switched on are sent to the
44
Quantum Radar. At subsequent power cycles the
Quantum Radar will automatically connect to the
MFD with the strongest signal.
Note:
1. During initial set up you will have 10 minutes in
2. Networked MFDs that only have their Wi-Fi
1. Apply power to your MFD(s).
2. Power on and then enable the Wi-Fi connection
3. Apply power to your Radar scanner.
4. Select Quantum Radar from the External
5. Select Pair with Quantum Radar.
6. If prompted, select Ok to enable your MFD's
7. Enter the Radar's SSID (e.g. Quan-
Important:
• Ensure that the SSID and Passcode are entered
• The SSID is always made up of the word
8. Select Connect.
TM MFD which also
9. Select Ok from the Successful Connection
which to connect the Radar to your MFD. After
this time, if no connection is made, the Radar
will automatically go to Sleep. If this occurs,
power cycle the Radar to bring it out of Sleep
mode and establish a connection.
enabled after the initial pairing period, will
send Wi-Fi credentials to the Radar when their
Wi-Fi is switched on.
to the MFDs which have the strongest signal, as
identified during the pre-installation site survey.
Usually these will be the MFDs closest to and / or
with the clearest line of sight to the Radar).
Devices menu on the MFD: (Homescreen >
Set-up > System Settings > External Devices
> Quantum Radar).
Wi-Fi connection.
tum_1234567) in the SSID field and the
passcode (e.g. 901589f5) in the Passcode
field.
Refer to the Retain your Wi-Fi Passcode
for details on locating your SSID and Passcode.
exactly as shown on the serial number label that
was supplied with the Radar.
"Quantum", followed by an underscore "_",
followed by the product's 7 digit serial number,
(e.g. Quantum_1234567).
The initial connection can take up to 2 minutes to
complete.
pop-up.
section