Cisco ASR 1001-HX Hardware Installation Manual
  1. Manuals
  2. Brands
  3. Cisco Manuals
  4. Network Router
  5. ASR 1001-HX
  6. Hardware installation manual

Cisco ASR 1001-HX Hardware Installation Manual

Hide thumbs Also See for ASR 1001-HX:
Table of Contents

Advertisement

Quick Links

Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware

Installation Guide

First Published: 2016-10-17
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: 408 526-4000
800 553-NETS (6387)
Fax: 408 527-0883

Advertisement

Table of Contents
loading

Related Manuals for Cisco ASR 1001-HX

Summary of Contents for Cisco ASR 1001-HX

  • Page 1: Installation Guide

    Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide First Published: 2016-10-17 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 527-0883...
  • Page 2 Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks . Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company.

  • Page 3: Table Of Contents

    Serial Number and PID/VID Label Location Supported Hardware Components C H A P T E R 2 Supported EPAs Supported Transceivers Supported Crypto Module Supported DIMM Upgrade Power Supplies Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...
  • Page 4 Radio Frequency Interference Lightning and AC Power Fault Interference Rack-Mounting Guidelines Precautions for Rack-Mounting General Rack-Selection Guidelines Guidelines for 23-in. (Telco) Racks Equipment Rack Guidelines Locating for Safety Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...
  • Page 5 C H A P T E R 5 Checking Conditions Prior to System Startup Powering Up the Router Performing the Initial Configuration on the Router Using the Cisco setup Command Facility Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...
  • Page 6 Removing and Replacing the Power Supplies Removing AC Power Supplies Installing AC Power Supplies Removing DC Input Power Supplies Installing DC Input Power Supplies Wiring the DC Input Power Source Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...
  • Page 7 Port Signals and Pinouts A P P E N D I X B Management Ethernet Port Signals and Pinouts Console Port Signals and Pinouts Auxiliary Port Signals and Pinouts Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...
  • Page 8 Contents Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide viii...

  • Page 9: Document Revision History

    May 2016 First version of the document. Document Objectives This publication describes the installation of the Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router and replacement or upgrade of field-replaceable units (FRUs). Audience This publication is primarily designed for persons responsible for installing, maintaining, and troubleshooting the Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router.

  • Page 10: Document Organization

    Provides router specifications for the Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Port Signals and Pinouts Lists pinout specifications for the Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...
  • Page 11 Timesaver. Means reader be careful. In this situation, you might perform an action that could result in equipment Caution damage or loss of data. Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...

  • Page 12: Related Documentation

    Documentation, which also lists all new and revised Cisco technical documentation. Subscribe to the What's New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service and Cisco currently supports RSS version 2.0.

  • Page 13: Hardware Features

    Quantum Flow Processor that aggregates services at scale. The Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router are a part of the Cisco ASR 1000 Series and offers a compact form factor that consumes less rack space and power while offering 100 Gbps forwarding throughput.

  • Page 14: Chapter

    • 80 Mb ternary content-addressable memory (TCAM). • Field-replaceable units (FRU) with online insertion and removal (OIR). See Chapter 2, Supported Hardware Components for information on supported FRUs. Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...

  • Page 15: Front View

    SFP+ ports. The last four ports can be used as 1GE SFP or 10GE SFP+ ports USB ports 0 and 1 For the Cisco ASR 1001-HX Router, the power supplies (PEM 0 and PEM1), are located in the rear of Note the chassis. See...
  • Page 16 Ethernet port Two power supplies (AC or DC) are accessed from the front of the router and are hot-swappable. The Cisco ASR 1002-HX Router can support two AC or two DC power supplies. Do not install mixed Caution AC and DC power supply units in the same chassis.

  • Page 17: Slot Numbering

    Overview Front View Slot Numbering The Cisco ASR 1002-HX Router supports one Ethernet port adapter (EPA) in Bay 2. The following figure shows slot numbering on the Cisco ASR 1002-HX Router. Figure 3: Cisco ASR 1002-HX Router Slot Numbering Bay 0—Subslot 0/0/n connected to the built-in Bay 2—Subslot 0/2/n connected to the EPA...
  • Page 18 TE0 - TE7. Bay 2—EPA Slot Interfaces from 0 - 3 on both Bay 0 and Bay 1 on the Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Note Router are enabled by default. Interfaces from 4 - 7 can be enabled by purchasing the Paired Port License.

  • Page 19: Management And Storage Connections

    Overview Front View Management and Storage Connections The following figure shows the management and storage connections for the ASR 1001-HX Router. Figure 6: Management and Storage Connections for the Cisco ASR 1001-HX Router USB port 1 AUX—RJ-45/RS-232 compatible auxiliary port.

  • Page 20: Leds

    Overview Front View CON—Mini USB connector console port. AUX—RJ-45/RS-232 compatible auxiliary port. LEDs The following figure shows the LEDs on the front panel of the Cisco ASR 1001-HX Router. Figure 8: Cisco ASR 1001-HX LEDs LED Label Description Color Behavior...

  • Page 21: Cisco Asr 1001-Hx Router And Cisco Asr 1002-Hx Router Hardware Installation Guide

    Amber Indicates the crypto module is present but inoperable. Indicates the crypto module is not installed. The following figure shows the LEDs on the front panel of the Cisco ASR 1002-HX Router. Figure 9: Cisco ASR 1002-HX LEDs LED Label...

  • Page 22: Rear View

    Indicates the crypto module is present but inoperable. Indicates the crypto module is not installed. Rear View The following figure shows the rear of the Cisco ASR 1001-HX Router. Figure 10: Cisco ASR 1001-HX Router Rear View Fans Power supply (PEM 0)

  • Page 23: Cisco Product Identification Standard

    The fans are numbered from 0 to 5, right to left. Two power supplies (AC or DC) are accessed from the rear of the router and are hot-swappable. The Cisco ASR 1001-HX Router can support two AC or two DC power supplies. Do not install mixed Caution AC and DC power supply units in the same chassis.

  • Page 24: Unique Device Identifier

    — Additional product information The combination of serial number and product ID (PID) is unique and consistent across all Cisco products. The PID that is coded on hardware is called a base product identifier. Additional orderable PIDs can be associated to a base PID. For instance, an orderable PID may describe a packaging configuration for a product or a bundled group of products sold, tested, and shipped together.

  • Page 25: Cisco Asr 1001-Hx Router And Cisco Asr 1002-Hx Router Hardware Installation Guide

    Common Language Equipment Identification (CLEI) code is a ten-digit character code that identifies a Note specific product. A CLEI code is applied to each part within a Cisco ASR1002-HX Router as they are programmed in manufacturing for shipment to customers.

  • Page 26: Serial Number And Pid/Vid Label Location

    Serial Number and PID/VID Label Location Serial Number and PID/VID Label Location The following figures show the location of the serial number and the PID/VID label on the Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router. Figure 12: Cisco ASR 1001-HX Router Serial Number and PID/VID Label Location...

  • Page 27: Supported Hardware Components

    C H A P T E R Supported Hardware Components This chapter contains information about the supported hardware components on the Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router, and contains the following sections: • Supported EPAs, page 15 •...

  • Page 28: Cisco Asr 1001-Hx Router And Cisco Asr 1002-Hx Router Hardware Installation Guide

    An EPA has two types of LEDs: an A/L (Active/Link) LED for each port on the EPA, and a STATUS LED, as shown in the following figure. Figure 14: EPA-18X1GE LEDs Figure 15: EPA-10X10GE LEDs STATUS Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...

  • Page 29: Supported Transceivers

    EPA power is off. Related Topics Removing and Replacing an EPA, on page 128 Supported Transceivers The Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router support the following small form-factor pluggable (SFP) and CPAK optical transceiver types: Ports Cisco ASR 1001-HX Router...

  • Page 30: Cisco Asr 1001-Hx Router And Cisco Asr 1002-Hx Router Hardware Installation Guide

    SFP-10G-LR-X 10GBASE-LR SFP+ Module for Extended Temp range SFP-10G-ER 10GBASE-ER SFP+ Module for SMF SFP-H10GB-ACU7M 10GBASE-CU SFP+ Cable 7 Meter, active SFP-H10GB-ACU10M 10GBASE-CU SFP+ Cable 10 Meter, active Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...

  • Page 31: Supported Crypto Module

    OTU4 rate is also supported. Optical multiplexing and demultiplexing of the four wavelengths are managed within the module. Supported Crypto Module The Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router support the following crypto module: Description ASR1001HX-IPSECHW Cisco ASR1001-HX crypto module with no default crypto throughput.

  • Page 32: Power Supplies

    Removing and Replacing a DIMM, on page 117 Power Supplies The Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router support AC or DC power supply options. The modular chassis configurations support the installation of two power supplies for redundancy. When an external power supply fails or is removed, the other power supply provides power requirements for the chassis.

  • Page 33: Ac Power Supply

    Note The direction of the airflow is different for the Cisco ASR 1001-HX Router and the Cisco ASR 1002-HX Router as shown by the arrows in the illustrations below. Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...

  • Page 34: Dc Power Supply

    Supported Hardware Components DC Power Supply The following figure shows the Cisco ASR 1001-HX Router AC power supply. Figure 16: ASR1000X-AC-750W AC Power Supply Used in the Cisco ASR 1001-HX Router AC power connector FAIL and OK LEDs Handle Retaining latch The following figure shows the Cisco ASR 1002-HX Router AC power supply.

  • Page 35: Cisco Asr 1001-Hx Router And Cisco Asr 1002-Hx Router Hardware Installation Guide

    Note The direction of the airflow is different for the Cisco ASR 1001-HX Router and the Cisco ASR 1002-HX Router as shown by the arrows in the illustrations below. The following figure shows the Cisco ASR 1001-HX Router DC power supply.

  • Page 36: Power Supply Leds

    Supported Hardware Components Power Supply LEDs The following figure shows the Cisco ASR 1002-HX Router DC power supply. Figure 19: ASR1000X-DC-950W DC Power Supply Used in the Cisco ASR 1002-HX Router DC power connections FAIL and OK LEDs Handle Retaining latch Power Supply LEDs The following table describes the power supply LEDs.

  • Page 37: Power Supply Fans

    The power supplies do not depend on the system-level fans for cooling. Fan failure is determined by fan-rotation sensors. The fans in the Cisco ASR 1001-HX Router power supplies have plug-side exhaust airflow. The fans in Note the Cisco ASR 1002-HX Router power supplies have plug-side intake airflow.

  • Page 38: Cisco Asr 1001-Hx Router And Cisco Asr 1002-Hx Router Hardware Installation Guide

    Power Cord, 250 VAC 10 A, C14-C13 Connectors CAB-C13-C14-JMPR Cabinet Power Cord, 250 VAC 13 A, C14-C15 Connector Jumper CAB-C13-C14-2M Power Cord Jumper, C13-C14 Connectors, 2-Meter Length CAB-C13-C14-AC Power Cord Jumper, C13-C14 Connectors, 3-Meter Length Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...

  • Page 39: Preparing Your Site For Installation

    Preparing Your Site for Installation This chapter contains important safety information you should know before working with the Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router, and guides you through the process of preparing your site for router installation.

  • Page 40: Site Planning Checklist

    • Router should always be transported or stored in its shipping package in the upright position. • Keep the router in the shipping container until you have determined the installation site. Inspect all items for shipping damage. If an item appears damaged, contact a Cisco customer service Note representative immediately.

  • Page 41: Safety Warnings

    Safety Recommendations The following guidelines will help to ensure your own safety and protect your Cisco equipment. This list does not cover all potentially hazardous situations, so be alert. • Cisco safety policy mandates that all its routers must conform to the requirements of IEC 60950, with appropriate national deviations, as a minimum.

  • Page 42: Standard Warning Statements

    Regulatory Compliance and Safety Information for the Cisco ASR 1000 Series Aggregation Services Routers. This section describes the warning definition and then lists core safety warnings grouped by topic. Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...

  • Page 43: General Safety Warnings

    Installation of the equipment must comply with local and national electrical codes. Warning Statement 1030—Equipment Installation Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...

  • Page 44: Cisco Asr 1001-Hx Router And Cisco Asr 1002-Hx Router Hardware Installation Guide

    This product relies on the building's installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than: • 20 A U.S. maximum (ASR 1001-HX Router and ASR 1002-HX Router) • 20 A U.S. maximum (ASR 1001-HX Router) •...

  • Page 45: Cisco Asr 1001-Hx Router And Cisco Asr 1002-Hx Router Hardware Installation Guide

    Viewing the laser output with certain optical instruments (for example, eye loupes, magnifiers, and microscopes) within a distance of 100 mm may pose an eye hazard. Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...

  • Page 46: Site Planning

    Site Planning This section contains site-planning information, and will help you plan for the installation of the Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router. General Precautions...

  • Page 47: Site Selection Guidelines

    The following sections provide specific information to help you plan for a proper operating environment. The Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router are designed to meet the industry EMC, safety, and environmental standards described in the Regulatory, Safety, and Compliance Information for Cisco ASR 1000 Series Aggregation Services Routers document.

  • Page 48: Physical Characteristics

    • Guidelines for 23-in. (Telco) Racks, on page 42 The following table shows the weight and dimensions of the Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router: Table 8: Physical Characteristics of the Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router...

  • Page 49: Site Power Guidelines

    • Ships with forward rack-mount brackets installed and an extra set included in the accessory kit Site Power Guidelines The Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router has specific power and electrical wiring requirements. Adhering to these requirements ensures reliable operation of the system. Follow these precautions...

  • Page 50: Electrical Circuit Requirements

    The following table lists AC and DC power supply system rating requirements for the Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router. Table 10: AC and DC Power Supply System Rating Specifications for the Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router...

  • Page 51: Console Port Connections

    (CSUs), or data service units (DSUs). Before you install the Cisco ASR 1001-HX Router or Cisco ASR 1002-HX Router, have all the additional external equipment and cables at hand. For ordering information, contact a Cisco customer service representative.

  • Page 52: Interference Considerations

    Strong EMI can destroy the signal drivers and receivers in the Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router and even create an electrical hazard by causing power surges through power lines into installed equipment.

  • Page 53: Lightning And Ac Power Fault Interference

    Lightning and AC Power Fault Interference If signal wires exceed recommended cabling distances, or if signal wires pass between buildings, you should consider the effect that a lightning strike in your vicinity might have on the Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router.

  • Page 54: Guidelines For 23-In. (Telco) Racks

    Locating for Safety If the Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router is the heaviest or the only piece of equipment in the rack, consider installing it at or near the bottom to ensure that the rack’s center of gravity is as low as possible.

  • Page 55: Locating For Easy Maintenance

    "Environmental Monitoring and Reporting Functions" section. • Keep the Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router off the floor and out of the areas that collect dust. • Follow ESD-prevention procedures to avoid damage to equipment. Damage from static discharge can cause immediate or intermittent equipment failure.

  • Page 56: Electrical Safety

    In addition, use the following guidelines when working with any equipment that is disconnected from a power source, but is still connected to telephone wiring or other network cabling: • Never install telephone wiring during a lightning storm. Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...

  • Page 57: Chassis-Lifting Guidelines

    The following tools and equipment are recommended as the minimum necessary equipment to install the Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router. You may need additional tools and equipment to install associated equipment and cables. You may also require test equipment to check electronic and optical signal levels, power levels, and communications links.

  • Page 58: Unpacking And Verifying Shipping Contents

    Cisco ASR 1002-HX Router shipping container. Do not discard the shipping container. You need the container if you move or have to ship the Cisco ASR 1001-HX Router or Cisco ASR 1002-HX Router in the future. Table 12: Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Shipping Container Contents...

  • Page 59: Installation Checklist

    Required passwords, IP addresses, device names, and so on, available Required tools available Network connection equipment available Cable-management brackets installed (optional, but recommended) AC power cable(s) connected to AC source(s) and router Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...

  • Page 60: Installation Checklist

    System boot complete (STATUS LED is on) Ethernet port adapters and NIMs (where applicable) are operational Correct hardware configuration displayed after system banner appears Correct licenses installed on the router Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...

  • Page 61: Installing The Router

    Connecting Cables, page 67 Installation Methods The Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router are designed for standalone, 2-rail 19-inch rack-mount (front rail only), and 4-rail 19-inch rack-mount (front and rear rail) installations. Although rack-mounting is the preferred method of installation, you can mount the chassis on an equipment shelf or tabletop.

  • Page 62: Guidelines For A Standalone Equipment Shelf Or Tabletop Installation

    • The Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router require at least 3 inches (7.62 cm) of clearance at the inlet and exhaust vents (the front and rear sides of the chassis).

  • Page 63: Installing The Router On A Standalone Equipment Shelf Or Tabletop

    Step 2 Lift the chassis into position on the equipment shelf or tabletop. Step 3 through Step 9 are optional if you are installing the Cisco ASR 1001-HX Router or Cisco Note ASR 1002-HX Router on a rack shelf. The chassis rack-mount brackets must be installed prior to installing the cable-management brackets.
  • Page 64 Guidelines for Rack Installation • The Cisco ASR 1001-HX Router requires a minimum of 1.75 inches or 4.45 cm rack units of vertical rack space. The Cisco ASR 1002-HX Router requires a minimum of 3.5 inches or 8.9 cm rack units of vertical rack space.

  • Page 65: Verifying Rack Dimensions

    The following figure shows the brackets attached to the chassis. Depending on the bracket holes you use, the chassis may protrude in the rack. Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...

  • Page 66: Attaching The Front Rack-Mount Brackets

    Locate the threaded holes on the side of the chassis. Ensure that you hold the front rack-mount bracket with the ear and holes facing outward and towards the front of the chassis. The following figures show where to attach the front rack-mount brackets to the Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router.

  • Page 67: Attaching The Rear Rack-Mount Brackets

    Installing the Router Attaching the Rear Rack-Mount Brackets Figure 22: Attaching the Front Rack-Mount Brackets to the Cisco ASR 1002-HX Router Front rack-mount bracket ear and holes Front rack-mount bracket screws Front rack-mount bracket Step 2 Position the front rack-mount bracket top hole with the chassis, first top hole behind the side vent holes.

  • Page 68: Attaching The Rear Rack-Mount Brackets

    Locate the threaded holes on the side of the chassis. Ensure that you hold the rear rack-mount bracket with the ear and holes facing outward and towards the rear of the chassis. The following figures show where to attach the rear rack-mount brackets to the Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router.

  • Page 69: Mounting The Router In The Rack

    The Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router can be installed on a two-post rack, either 19 inch or 23 inch. We recommend that you allow at least 1 or 2 inches (2.54 or 5.08 cm) of vertical clearance between the router and any equipment directly above and below it.
  • Page 70 Step 8 Tighten all the screws on each side to secure the chassis to the equipment rack. The following figures show the Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router on a two-post equipment rack. Figure 25: Cisco ASR 1001-HX Router Installed on a Two-Post Equipment Rack...

  • Page 71: Four-Post Rack Installation

    Procedure Step 1 (Optional) Install a shelf in the rack to support the Cisco ASR 1001-HX Router or Cisco ASR 1002-HX Router. If you use a shelf, it helps support the chassis while you secure it to the rack. If you are using a shelf, place the chassis on the shelf and slightly raise the front of the chassis to...

  • Page 72: Four-Post Rack Installation

    Step 6 Tighten all the screws on each side to secure the chassis to the equipment rack. The following figures show the Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router on a four-post equipment rack. Figure 27: Cisco ASR 1001-HX Router in a Four-Post Rack — Front and Rear Rack-Mounting...

  • Page 73: Four-Post Rack Installation

    Installing the Router Four-Post Rack Installation Figure 28: Cisco ASR 1002-HX Router in a Four-Post Rack — Front and Rear Rack-Mounting Rear rack equipment rail Front rack mount bracket ear and screws Rear rack mount bracket ear and screws Front rack equipment rail...

  • Page 74: Attaching The Cable Management Bracket

    Procedure Step 1 Align the cable-management bracket to the rack-mount bracket on one side of the Cisco ASR 1001-HX Router or Cisco ASR 1002-HX Router. The cable-management bracket aligns to the top hole of the chassis rack-mount bracket. Step 2 Using a Phillips screwdriver, insert one screw through the top screw hole of the cable-management bracket and into the chassis rack-mount bracket and tighten the screw.

  • Page 75: Attaching The Cable Management Bracket

    Step 3 Do one of the following as appropriate: • Cisco ASR 1001-HX Router—Insert the cable management screw into the screw hole of the cable-management bracket and into the chassis rack-mount bracket and tighten the screw using a Phillips screwdriver.

  • Page 76: Chassis Ground Connection

    (earth) connection for the chassis. A chassis ground connector is provided on each Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router. There is a stud on the rear left side of the chassis. The grounding wire should always be the first to be installed or connected and the last to be removed or Caution disconnected.

  • Page 77: Attaching A Chassis Ground Connection

    Step 5 Insert the two screws through the holes in the grounding lug. The following figures show how to attach a grounding lug to the chassis ground connector. Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...

  • Page 78: Chassis Ground Connection

    Installing the Router Attaching a Chassis Ground Connection Figure 32: Attaching the Grounding Lug to the Ground Connector of the Cisco ASR 1001-HX Router Chassis ground lug Ground connector on the chassis Grounding screws Ground symbol Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...

  • Page 79: Connecting Cables

    Connect the opposite end of the grounding wire to the appropriate grounding point at your site to ensure an adequate chassis ground. Connecting Cables Keep the following guidelines in mind when connecting any external cable to the Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router: Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...

  • Page 80: Connecting The Console And Auxiliary Port Cables

    Step 2 Connect one end of the RJ-45 cable to the serial RJ-45 console port (CON) on the Cisco ASR 1001-HX Router or Cisco ASR 1002-HX Router using the RJ-45 to DB-9 cable. Connect the DB-9 end to your terminal equipment.

  • Page 81: Connecting To The Mini Usb Console Port

    The default parameters for the console port are 9600 baud, 8 data bits, no parity, and 1 stop bit. For operation with a Microsoft Windows OS version older than Windows 7, the Cisco Windows USB Console Driver must be installed on any PC connected to the console port. If the driver is not installed, prompts guide you through a simple installation process.

  • Page 82: Cisco Asr 1001-Hx Router And Cisco Asr 1002-Hx Router Hardware Installation Guide

    Installing the Router Management Ethernet Port Cable Connection Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...

  • Page 83: Power Up And Initial Configuration

    Do not operate the system unless all cards, faceplates, front covers, and rear covers are in place. To view the boot sequence, you must have a console connection to the Cisco ASR 1001-HX Router or Note Cisco ASR 1002-HX Router before it powers up.

  • Page 84: Powering Up The Router

    LEDs, see the "LEDs" section. Step 2 Observe the initialization process. When the system boot is complete (the process takes a few seconds), the router begins to initialize. Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...

  • Page 85: Cisco Asr 1001-Hx Router And Cisco Asr 1002-Hx Router Hardware Installation Guide

    GPL Version 2.0 is free software that comes with ABSOLUTELY NO WARRANTY. You can redistribute and/or modify such GPL code under the terms of GPL Version 2.0. For more details, see the Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...

  • Page 86: Performing The Initial Configuration On The Router

    If you are unable to comply with U.S. and local laws, return this product immediately. A summary of U.S. laws governing Cisco cryptographic products may be found at: http://www.cisco.com/wwl/export/crypto/tool/stqrg.html If you require further assistance please contact us by sending email to export@cisco.com.

  • Page 87: Cisco Asr 1001-Hx Router And Cisco Asr 1002-Hx Router Hardware Installation Guide

    Note booted into Cisco IOS-XE. For information on modifying the configuration after you create it, see the Cisco IOS XE Configuration Guide and the Cisco IOS XE Command References. This section explains how to configure a host name for the router, set passwords, and configure an interface to communicate with the management network.

  • Page 88: Cisco Asr 1001-Hx Router And Cisco Asr 1002-Hx Router Hardware Installation Guide

    Configure IP on this interface? [yes]: yes IP address for this interface [10.10.10.12]: Subnet mask for this interface [255.0.0.0] : 255.255.255.0 Class A network is 10.0.0.0, 24 subnet bits; mask is /24 Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...

  • Page 89: Completing The Configuration

    Completing the Configuration When using the Cisco setup command facility, and after you have provided all the information requested by the facility as described in “Using the Cisco setup Command Facility” section, the final configuration appears. To complete your router configuration, follow these steps:...

  • Page 90: Using The Cisco Ios-Xe Cli-Manual Configuration

    If the system configuration message does not appear, it means a default configuration file was installed on the router prior to shipping. Follow these steps to configure the router. Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...

  • Page 91: Configuring The Router Hostname

    Step 3 hostname name Specifies or modifies the hostname for the network server. Example: Router(config)# hostname myrouter Step 4 (Optional) Returns to privileged EXEC mode. Example: myrouter# end Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...

  • Page 92: Configuring The Enable And Enable Secret Passwords

    If you configure the enable secret command, it takes precedence over the enable password command; the two commands cannot be in effect simultaneously. For more information, see the “Configuring Passwords and Privileges” chapter in the Cisco IOS Security Configuration Guide. Also see the...

  • Page 93: Configuring The Console Idle Privileged Exec Timeout

    For more information on configuring the console line, see the Cisco IOS Configuration Fundamentals and Network Management Configuration Guide. In particular, see the “Configuring Operating Characteristics for Terminals” and “Troubleshooting and Fault Management”...

  • Page 94: Gigabit Ethernet Management Interface Overview

    Interfaces” chapter of the Cisco IOS Interface and Hardware Component Configuration Guide. For information on interface numbering, see the software configuration guide pertaining to your router. Procedure Command or Action Purpose Step 1 enable Enables privileged EXEC mode. Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...
  • Page 95 Verify that the interfaces are up and configured Router# show ip interface brief correctly. For comprehensive configuration information about IP routing and IP routing protocols, see the Configuring Note IP Routing Protocol-Independent Feature on Cisco.com. Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...

  • Page 96: Saving Your Router Configuration

    Note To aid file recovery and minimize downtime in case of file corruption, we recommend that you save backup copies of the startup configuration file and the Cisco IOS-XE software system image file on a server. Note To avoid losing work you have completed, be sure to save your configuration occasionally as you proceed.

  • Page 97: Powering Off The Router Safely

    • show configuration—Helps verify if you have configured the correct hostname and password. After you have completed and verified the initial configuration, the specific features and functions are ready to be configured. See the Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide. Powering Off the Router Safely Before You Begin We recommend that before turning off all power to the chassis, you issue the reload command.

  • Page 98: Alarm Monitoring

    To clear a visual alarm, you must resolve the alarm condition. The clear facility-alarm command does not clear an alarm LED on the Cisco ASR 1001-HX Router or Cisco ASR 1002-HX Router. For example, if a critical alarm LED is illuminated because an active EPA was removed without a graceful deactivation of the EPA, the only way to resolve that alarm is to replace the EPA.

  • Page 99: Environmental Monitoring

    The fans are located at the rear of the chassis. The fans in the Cisco ASR 1001-HX Routerare numbered from 0 to 5, right to left. The fans in the Cisco ASR 1002-HX Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...

  • Page 100: Reporting Functions

    The chassis manager on the forwarding engine control processor manages the local resources of the forwarding processor. The Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router display warning messages on the console if the chassis interface-monitored parameters exceed a threshold. You can also retrieve and display environmental status reports with the following commands: •...
  • Page 101 Uptime for this control processor is 7 minutes System returned to ROM by reload System image file is "bootflash:asr1002hx-universalk9.BLD_V162_1_THROTTLE_LATEST_ 20160119_234422_V16_2_0_259.SS" Last reload reason: Reload Command This product contains cryptographic features and is subject to United Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...
  • Page 102 If you are unable to comply with U.S. and local laws, return this product immediately. A summary of U.S. laws governing Cisco cryptographic products may be found at: http://www.cisco.com/wwl/export/crypto/tool/stqrg.html If you require further assistance please contact us by sending email to export@cisco.com.
  • Page 103 00:01:42 ASR1001-HX ok, active 00:03:19 ASR1000X-AC-750W 00:03:00 ASR1000X-AC-750W 00:03:00 ASR1001HX-FAN 00:03:00 Slot CPLD Version Firmware Version --------- ------------------- --------------------------------------- 15081816 16.2(2r) 15081816 16.2(2r) 15081816 16.2(2r) Router# Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...
  • Page 104 PCB Serial Number : JAE1931098L RMA Test History : 00 RMA Number : 0-0-0-0 RMA History : 00 Top Assy. Part Number : 68-5448-02 CLEI Code : SAMPL00XYZ Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...
  • Page 105 Environment Monitor Data : 05 02 03 50 03 58 00 4B Platform features : 00 00 03 56 1E 53 0F 2A 00 00 00 00 00 00 00 00 Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...
  • Page 106 Power Up and Initial Configuration Reporting Functions Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...

  • Page 107: License Verification

    • Configuring the Crypto Throughput Level, page 109 Viewing the Cisco IOS License Level Use the show version command to determine the Cisco IOS license level in the router. For example: Router# show version License Level: adventerprise License Type: RightToUse...

  • Page 108: Viewing License Information

    Use the show license all command to display all the applicable licenses in both Primary License Storage and Built In License Storage. Primary License Storage stores the currently purchased and installed licenses. Note Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...
  • Page 109 License Verification Viewing License Information The following example displays sample output from the show license all command for the Cisco ASR 1001-HX Router: Router# show license all License Store: Primary License Storage License Store: Built-In License Storage StoreIndex: 0 Feature: adventerprise Version: 1.0...
  • Page 110 4 days Evaluation period left: 5 weeks 3 days Period used: 3 weeks 0 Transition date: Sep 04 2016 00:20:43 License Count: 2/0 (In-use/Violation) License Priority: Low Router# Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...
  • Page 111 License Verification Viewing License Information The following example displays sample output from the show license all command for the Cisco ASR 1002-HX Router: Router# show license all License Store: Primary License Storage License Store: Built-In License Storage StoreIndex: 0 Feature: adventerprise Version: 1.0...
  • Page 112 License State: Active, Not in Use, EULA accepted Evaluation total period: 8 weeks 4 days Evaluation period left: 7 weeks 1 Period used: 1 week days License Count: 0/0 (In-use/Violation) License Priority: Low Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...

  • Page 113: Port Licensing

    Port Licensing for the Cisco ASR 1001-HX Router The Cisco ASR 1001-HX Router has eight 1GE SFP ports in Bay 0 and eight 1GE SFP or 10GE SFP+ ports in Bay 1 . By default, four ports in Bay 0 and four ports in Bay 1 can be enabled without a license (ports 0 through 3).
  • Page 114 Cisco ASR 1001-HX Router Licensing The Cisco ASR 1001-HX Router image carries four 1GE and two 10GE port EvalRTU (Evaluation) licenses. If the EvalRTU license expires, it becomes a Right-To-Use (RTU) license. • Licensed ports in Bay 0 use a 1GE port license.

  • Page 115: Licensing Scenarios For Cisco Asr 1001-Hx Router

    Licensing Scenarios for Cisco ASR 1001-HX Router The following table provides all possible licensing scenarios for the Cisco ASR 1001-HX Router. It also provides information about what you need to do to change from 1G SFP to 10G SFP+ and vice versa; or transition from 1G SFP or 10G SFP+ to "No License".
  • Page 116 10G SFP+ is on port 6 and 1G SFP on port 5 is on port 7 before using the no shut No SFP is on command port 6 and 1G SFP is present on port 7 Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...
  • Page 117 SHUT NO_SHUT—10G 10G License SHUT SHUT No License Transition 1G SFP license to "No NO_SHUT—1G NO_SHUT—1G 1G License — License" SHUT NO_SHUT—1G 1G License SHUT SHUT No License Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...

  • Page 118: Port Licensing For The Cisco Asr 1002-Hx Router

    Port Licensing for the Cisco ASR 1002-HX Router The Cisco ASR 1002-HX Router has eight 1GE ports in Bay 0 and eight 10GE ports in Bay 1. By default, four ports in Bay 0 and four ports in Bay 1 can be enabled without a license (ports 0 through 3). The remaining ports can be enabled in pairs (ports 4 and 5, and ports 6 and 7) through licenses.

  • Page 119: Licensing Scenarios For Cisco Asr 1002-Hx Router

    Two port pairs in use for the evaluation license (an EULA was accepted for each prior to use). Licensing Scenarios for Cisco ASR 1002-HX Router The following table provides all possible licensing scenarios for the Cisco ASR 1002-HX Router. Scenario Slot 4...

  • Page 120: Evaluation License Features

    Permanent and Evaluation licenses. In this case, the Evaluation License becomes Active since it can accommodate both port pairs. The Permanent License will automatically become Active if and when its port-count meets the user’s desired configuration. Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...

  • Page 121: Configuring The Crypto Throughput Level

    The Cisco ASR 1001-HX Router supports throughput levels of 8 Gbps or 16 Gbps. The Cisco ASR 1002-HX Router supports throughput levels of 8 Gbps, 16 Gbps, or 25 Gbps. The following two types of crypto throughput licenses are available on the Cisco ASR 1001-HX Router and the Cisco ASR 1002-HX Router: •...
  • Page 122 For example, configuring 16-25g on the Cisco ASR 1002-HX Router automatically enables 8g and 8-16g as RTU. For more information about the software-activated performance upgrade license, see the Software Activation Configuration Guide. Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...

  • Page 123: Removing And Replacing Frus

    Note can be hot-swapped. The Cisco ASR 1001-HX Router has two power supply slots that are accessed from the rear of the chassis: Note power supply slot 0 (PS0) and power supply slot 1 (PS1) are on the left of the chassis power switch.

  • Page 124: Removing Ac Power Supplies

    Repeat these steps if it is required to remove the other AC power supply. Installing AC Power Supplies Do not install the power supplies with the chassis cover off. Note Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...

  • Page 125: Removing Dc Input Power Supplies

    Installing DC Input Power Supplies Statement 1003—DC Power Disconnection Warning Before performing any of the following procedures, ensure that power is removed from the DC circuit. Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...
  • Page 126 To avoid hazardous conditions, all components in the area where DC input power is accessible must be Note properly insulated. Therefore, before installing the DC cable lugs, be sure to insulate the lugs according to the manufacturer's instructions. Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...

  • Page 127: Wiring The Dc Input Power Source

    It is not required to place the power switch in the Standby position if you want to hot-swap a single power supply. Step 3 Remove the plastic cover from the terminal block. Before you continue to install the terminal block ground wires, stop and perform Step Caution Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...
  • Page 128 Sleeving is not required for insulated terminals. Figure 37: DC Power Supply Terminal Block Ground Cable Lugs This illustration shows the DC power supply for the Cisco ASR 1002-HX Router. The airflow for Note the Cisco ASR 1001-HX Router is reverse of what is shown in this illustration.

  • Page 129: Removing And Replacing Usb Flash Memory Stick

    Step 2 To replace a Cisco USB Flash memory stick, insert the module into USB port 0 or 1. The Flash memory stick can be inserted only in one way, and can be inserted or removed regardless of whether the router is powered up or not.

  • Page 130: Removing A Dimm From A Cisco Asr 1001-Hx Router

    Removing a DIMM from a Cisco ASR 1001-HX Router Cisco ASR 1001-HX Router The Cisco ASR 1001-HX Router has two DIMM slots and supports 8-GB configuration by default (two 4-GB DIMMS), and can be upgraded to 16-GB (two 8-GB DIMMS) configuration.
  • Page 131 Step 3 Position the chassis so that you have the most comfortable access to the chassis to remove the DIMM. Step 4 Locate the DIMMs on the router. Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...
  • Page 132 Removing and Replacing FRUs Removing a DIMM from a Cisco ASR 1001-HX Router The following figure shows the location of the DIMM slots in the Cisco ASR 1001-HX Router. Figure 39: Cisco ASR 1001-HX Router and DIMM Location Cisco ASR 1001-HX Router and DIMM location (two slots) Step 5 Pull down the DIMM module spring latches to release the corresponding DIMM from the socket.

  • Page 133: Replacing A Dimm In A Cisco Asr 1001-Hx Router

    DIMM. Caution When inserting DIMMs, use firm but not excessive pressure. If you damage a socket, you will have to return the router to the factory for repair. Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...
  • Page 134 If a DIMM appears to stick out or rest in the socket at a different angle from the other, remove the DIMM and reinsert it. Replace the top chassis cover, and reboot the system for another installation check. Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...

  • Page 135: Removing A Dimm From A Cisco Asr 1002-Hx Router

    Removing a DIMM from a Cisco ASR 1002-HX Router Before You Begin Perform the following steps before you begin the process of removing and replacing a DIMM from a Cisco ASR 1002-HX Router: • Use an ESD-preventive wrist strap.
  • Page 136 Step 3 Position the chassis so that you have the most comfortable access to the chassis to remove the DIMM. Step 4 Locate the DIMMs on the router. Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...
  • Page 137 Removing and Replacing FRUs Removing a DIMM from a Cisco ASR 1002-HX Router The following figure shows the location of the DIMM slots in the Cisco ASR 1002-HX Router. Figure 44: Cisco ASR 1002-HX Router DIMM Location Cisco ASR 1002-HX Router DIMM location (four slots)

  • Page 138: Replacing A Dimm In A Cisco Asr 1002-Hx Router

    DIMM. When inserting DIMMs, use firm but not excessive pressure. If you damage a socket, you will Caution have to return the router to the factory for repair. Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...
  • Page 139 Installing DC Input Power Supplies What to Do Next After you have correctly installed the Cisco ASR 1002-HX Router DIMMs, the system should reboot properly. If the system fails to reboot properly or if the console terminal displays a checksum or memory error after you have installed the new DIMMs, ensure that all DIMMs are installed correctly.

  • Page 140: Removing And Replacing An Epa

    If a DIMM appears to stick out or rest in the socket at a different angle from the other, remove the DIMM and reinsert it. Replace the top chassis cover, and reboot the system for another installation check. After several attempts, if the system fails to restart properly, contact a Cisco service representative for Note assistance.

  • Page 141: Removing An Epa

    Caution Removing an EPA while traffic is flowing through the ports may cause system disruption. a) At the prompt, enter hw-module subslot 0/2 stop and press Enter. router# Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...

  • Page 142: Replacing An Epa

    Use the show platform command to verify whether the status of subslot 0/2 is OK. Router# show platform Chassis type: ASR1002-HX Slot Type State Insert time (ago) --------- ------------------- --------------------- ----------------- ASR1002-HX 00:07:52 BUILT-IN-EPA-8x1G 00:07:00 BUILT-IN-EPA-8x10G 00:07:00 EPA-18X1GE 00:07:01 Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...

  • Page 143: Removing And Replacing Fans

    Removing and Replacing Fans Removing the Fans from a Cisco ASR 1001-HX Router Before You Begin Perform the following steps before you begin the process of removing the fans from a Cisco ASR 1001-HX Router: • Use an ESD-preventive wrist strap.
  • Page 144 Position the chassis so that you have the most comfortable access to the chassis to remove the fans. The fans are located at the rear of the chassis. Step 4 Unplug the six fan connectors from the motherboard. Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...
  • Page 145 Remove the three screws from the rear of the chassis as shown in the following figure. Step 6 Rotate the fan tray slightly forward, and then lift it out of the chassis as shown in the following figure. Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...

  • Page 146: Replacing The Fans In A Cisco Asr 1001-Hx Router

    Replacing the Fans in a Cisco ASR 1001-HX Router Fan tray Replacing the Fans in a Cisco ASR 1001-HX Router Procedure Step 1 Gently insert the fan tray into the rear of the chassis. Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...
  • Page 147 Install the top surface screws and the side screws and tighten them slightly. Step 5 Install the power supplies into the chassis and power up the router. See: • Installing AC Power Supplies • Installing DC Input Power Supplies Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...

  • Page 148: Removing The Fans From A Cisco Asr 1002-Hx Router

    Removing the Fans from a Cisco ASR 1002-HX Router Removing the Fans from a Cisco ASR 1002-HX Router Before You Begin Perform the following steps before you begin the process of removing the fans from a Cisco ASR 1002-HX Router: • Use an ESD-preventive wrist strap.
  • Page 149 Position the chassis so that you have the most comfortable access to the chassis to remove the fans. The fans are located at the rear of the chassis. Step 4 Unplug the four fan connectors from the motherboard. Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...
  • Page 150 Remove the two screws from the rear of the chassis as shown in the following figure. Step 6 Lift the fan tray up and out of the chassis as shown in the following figure. Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...

  • Page 151: Replacing The Fans In A Cisco Asr 1002-Hx Router

    Replacing the Fans in a Cisco ASR 1002-HX Router Fan tray Replacing the Fans in a Cisco ASR 1002-HX Router Procedure Step 1 Gently insert the fan tray into the rear of the chassis. Fan tray Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...

  • Page 152: Installing The Crypto Module

    Installing the Crypto Module in a Cisco ASR 1001-HX Router Before You Begin Perform the following steps before you begin the process of installing the crypto module in a Cisco ASR 1001-HX Router: • Shut down the router. Enter the copy running-config startup-config command to save the configuration to NVRAM.
  • Page 153 Putting your thumbs in the thumb depression shown in the following figure, slide the cover slightly backward and lift it off of the chassis. Figure 51: Cisco ASR 1001-HX Router Top Cover Screw Locations Thumb depression location Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...

  • Page 154: Installing The Crypto Module In A Cisco Asr 1002-Hx Router

    To install the crypto module, you must shut down the router and remove it from the rack. Enter the copy running-config startup-config command to save the configuration to NVRAM. Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...
  • Page 155 Align the crypto module with the guide rails and carefully slide the crypto module into the slot until it is fully seated. Figure 54: Installing the Crypto Module Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...

  • Page 156: Repacking The Router

    If your system is damaged, you must repack it for return shipment. Before you return the router or move the router to a different location, repack the system using the original packaging material. Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...

  • Page 157: Appendix A Technical Specifications

    A P P E N D I X Technical Specifications This appendix provides technical specifications for the Cisco ASR 1001-HX and 1002-HX Router. • Cisco ASR 1001-HX Router Specifications, page 145 • Cisco ASR 1002-HX Router Specifications, page 146 Cisco ASR 1001-HX Router Specifications...

  • Page 158: Cisco Asr 1002-Hx Router Specifications

    5 to 90% Storage temperature –4° to 158° F (–20° to +70° C) Power consumption • Maximum (DC): 750 W • Maximum (AC): 750 W • Maximum (Out): 450 W Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...

  • Page 159: Appendix B Port Signals And Pinouts

    T/R Data + (Unused for 10/100) TX/RX DData - T/R Data - (Unused for 10/100) Console Port Signals and Pinouts The following table lists the pinouts of the RJ-45 console port. Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...

  • Page 160: Auxiliary Port Signals And Pinouts

    Output Data Terminal Ready (always On) Output Transmit Data Input Ring Indicator — — Input Receive Data DSR/DCD Input Data Set Ready/Data Carrier Detect Input Clear to Send Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide...

This manual is also suitable for:

Asr 1002-hx

Table of Contents