Getting The Desired Flame Effect - Dimplex CAS500 User Manual

• is the reduce flame button. Press this to reduce the height/intensity of your flame. You will hear an audible beep
when you reach the minimum level
• is the increase flame button. Press this to increase the height/intensity of your flame. You will hear an audible
beep when you reach the maximum level
• is the reduce fire crackling sound. Press this to reduce the volume of the crackling sound. The minimum volume
for this is off
• is the increase fire crackling sound. Press this to increase the volume of the crackling sound.
CAS1000
Mains Switch 'A':- Controls the electricity supply to the appliance.
Note: This switch must be in the 'ON' ( I ) position for the appliance to operate
Button panel 'A':- Controls the functioning of the left side of appliance
• is the on/standby button. Press it to turn on and off the flame effect. Turning it on will be indicated by the light
activating. Be careful not to look directly into the LED's. These are very bright. Although the main lights operate
immediately it will take a further 45 seconds before the flame effect starts.
• is the Pairing button. This will pair your remote control to the receiver. See 'Remote Control Operation' for details
• is the test mode button. This will be used by the manufacturer and the Service Engineer
• is the reduce flame button. Press this to reduce the height/intensity of your flame. You will hear an audible beep
when you reach the minimum level
• is the increase flame button. Press this to increase the height/intensity of your flame. You will hear an audible
beep when you reach the maximum level
• is the reduce fire crackling sound. Press this to reduce the volume of the crackling sound. The minimum volume
for this is off
• is the increase fire crackling sound. Press this to increase the volume of the crackling sound.
Button panel 'B':- Controls the functioning of the right side of appliance
• is the test mode button. This will be used by the manufacturer and the Service Engineer
• is the reduce flame button. Press this to reduce the height/intensity of your flame. You will hear an audible beep
when you reach the minimum level
• is the increase flame button. Press this to increase the height/intensity of your flame. You will hear an audible
beep when you reach the maximum level
• is the reduce fire crackling sound. Press this to reduce the volume of the crackling sound. The minimum volume
for this is off
• is the increase fire crackling sound. Press this to increase the volume of the crackling sound.

GETTING THE DESIRED FLAME EFFECT

1. Switch the appliance on by pressing the main switch to the on position and pressing the on/standby button. The
flames will start after 45 seconds. The flames will be at max height for 5 seconds and then reduce to a nominal level
2. Press the and
to the changes you make.
3. Do not tilt or move the appliance while there is water in the tank or sump
4. Make sure that the appliance is on a level surface
Once you have made your adjustments to both the flame height and crackling sound the appliance will keep these
settings even if you power off the appliance by either the on/standby button or by the main switch. The next time you
switch on the appliance it will start up as normal, wait 45 seconds for the flames to start, run at maximum height for 5
seconds and then revert to the adjusted settings.
REFILLING THE WATER TANK(S)
If you have chosen to operate your appliance by the Water Tanks provided, this section describes how to refill the Water
Tank on your CAS500 or CAS1000.
When the water in the tank(s) has been used up, the appliance will shut down the mist generation and cause the LED's
to continuously blink twice. In the case of a CAS1000 only one side of the product will blink, this is the side that has run
out of water. To refill follow the below steps;
1. Carefully lift off the fuelbed and set aside.
2. Press switch 'A' to the OFF (O) position.
3. Lift off the water tank(s), 1off on CAS500 and 2off on CAS1000 and take them to your water supply e.g. kitchen
4. Remove the cap by turning it anticlockwise
5. Fill with filtered tap water only
6. Replace the cap by turning it clockwise. Be careful not to over tighten
7. Place the bottle(s) back into position and wait until they finish filling the sump(s)
8. Press switch 'A' to the ON (I) position
buttons to adjust the flame to your desired level. Please give the flame generator time to react
4