Receiver Controls; Remote Control; Maintenance; General Tips - Dimplex CAS500 User Manual

9. Place the fuelbeds back on the product and make the DC connection see Fig7
10. Press on/standby on the receiver or the remote control to turn back on your appliance

RECEIVER CONTROLS

There are manual controls on the Receiver
CAS500
• is the on/standby button. Press it to turn on and off the flame effect.
• is the fire crackling sound. Press this to turn on and off the crackling sound. The volume is adjusted on the
manual controls of the appliance
• is the reduce flame button. Press this to reduce the height/intensity of your flame. You will hear an audible beep
when you reach the minimum level
• is the increase flame button. Press this to increase the height/intensity of your flame. You will hear an audible
beep when you reach the maximum level
CAS1000
• is the on/standby button. Press it to turn on and off the flame effect.
• is the fire crackling sound. Press this to turn on and off the crackling sound. The volume is adjusted on the
manual controls of the appliance
• is the reduce flame button for the left had side of the appliance. Press this to reduce the height/intensity of your
flame. You will hear an audible beep when you reach the minimum level
• is the increase flame button for the left had side of the appliance. Press this to increase the height/intensity of
your flame. You will hear an audible beep when you reach the maximum level
• is the reduce flame button for the right had side of the appliance. Press this to reduce the height/intensity of your
flame. You will hear an audible beep when you reach the minimum level
• is the increase flame button for the right had side of the appliance. Press this to increase the height/intensity of
your flame. You will hear an audible beep when you reach the maximum level

REMOTE CONTROL

The remote control is supplied with 2xAAA batteries. Remove the battery cover from the underside of the remote control
and after removing the batteries from the plastic wrapping fit them into place. Replace the battery cover.
The remote control has wireless technology and is required to be paired to the receiver. This is done by pressing the
button on Button Panel 'A', the LED's will start to blink on and off. This is to let you know that the appliance is ready to
connect to the remote control. Press the
control is paired to the appliance.
The operation of the remote control is the same as described in 'Receiver Controls'. You can pair multiple products to
the one remote control by repeating the pairing operation as above on your subsequent products.
PAIRING TO MULTIPLE PRODUCTS: If you are installing multiple CAS500/CAS1000 products you can pair them to
one remote control. To do this, please install the products as described in the "Installation Instructions". Please ensure
that the products are connected to mains power and have water supplied. If you are pairing CAS1000 and CAS500
products please choose the 6 button remote control as the master remote control. Pair the first product as described in
the 'REMOTE CONTROL' section above
1. On your second product press the rocker switch to the on (I) position, 1 beep
2. Press on the manual controls, 1 beep and the product will begin to start.
3. Press on the manual controls, beep and LED's start to blink.
4. Press on the remote control. The product will beep and LED's flash 5 times. The product will automatically switch
off.
5. Repeat the above steps to pair the next product.
When all products are paired, test the remote control by pressing (standby). If any of the products fail to receive a signal
from the remote control you can bring that product back in line with the others via the Manual Controls or the receiver
controls.

Maintenance

GENERAL TIPS

Only use filtered tap water in this appliance.
Always ensure that the appliance is sitting on a level surface.
If you intend not using the appliance for longer than 2 weeks, remove and empty the sump and water tank.
Once installed, never move this appliance or lay on its back, without draining the water from sump and water tank.
CLEANING
Warning – Always press Switch 'A' to the 'OFF' (0) position (Fig.9) and disconnect from the power supply before
cleaning the fire.
button on the remote control. The appliance will switch off. Now the remote
5