Optional Installation; Door Arm Hookup; Lift Handles; Pull Down Rope - Wayne-Dalton 105/110 Installation Instructions And Owner's Manual

optional Installation

Door Arm Hookup

Tools: Needle nose pliers
At the center of the top section, measure horizontally from the top of center hinge to the bottom
of strut. using that dimension, measure and cut (2) pieces of perforated angles. Assemble the
(2) pieces together using (2) 3/8" bolts and nuts (supplied by others). Now, secure to the top
section using carriage bolts and nuts (supplied by others), thru bolt both the perforated angles to
the top section, as shown.
Align the door arm with hole with one of the holes in the perforated angles. Secure the door
arm to the perforated angle using (1) 5/16" – 18 x 1" hex head bolt and (1) 5/16" – 18 lock nut
(supplied by others), as shown.
Strut
(2) 3/8" Hex bolt
and lock nut
(supplied by others).
(2) Perforated
angles

Lift Handles

Tools: Power drill, 1/8" Drill bit, Tape measure
NOTE: Lift handles must be lined up vertically.
Bottom Section:
Locate the exterior center stile or center most stile on the bottom section.
NOTE: For flush doors, find the center most stile by locating the center most hinge.
using the bottom hole of the lift handle, measure up 3" from the bottom of bottom section. Mark
the hole locations and drill (2) 9/32" dia. holes through the bottom section. On the outside of
the door, insert (2) 1/4" - 20 x 2 1/2" carriage bolts (black head) into the outside lift handle and
insert the assembly into the (2) pre-drilled holes in the bottom section. From the inside, slide the
(2) holes in the inside lift handle over the stems of the carriage bolts. Secure the outside and
inside lift handle to the bottom section with (2) 1/4" – 20 flange hex nuts.
Intermediate I Section:
Locate the exterior center stile or center most stile on the Intermediate I section. Mark a vertical
line on the section at that point.
NOTE: Some Garage Doors may require both lift handles to be installed on bottom section. If
your bottom section height is 28" or 29", install both lift handles onto the bottom section. Install
bottom lift handle per above instructions, then install the second lift handle a Minimum of 20"
and a Maximum of 30" above the bottom lift handle.
Measure up 4" from the bottom of the Intermediate I section. using this measurement as a
guide, position the bottom hole of the lift handle bottom at the mark. Make a mark at the top
hole of the lift handle. This should give you a Minimum of 20" and a Maximum of 30" between
the lower lift handle and the middle of the top lift handle. If needed, reposition the lift handle to
stay within the Minimum and Maximum dimensions, as stated above.
using the lift handle as a template, mark the hole locations and drill (2) 9/32" dia. holes through
the section. On the outside of the door, insert (2) 1/4" - 20 x 2 1/2" carriage bolts (black head)
into the outside lift handle and insert the assembly into the (2) pre-drilled holes in the section.
From the inside, slide the (2) holes in the inside lift handle over the stems of the carriage bolts.
Secure the outside and inside lift handle to the section with (2) 1/4" – 20 flange hex nuts.
Lift
handle
Intermediate I
section
Bottom
section Lift
handle
Strut
3"

Pull Down Rope

Tools: Power drill, 1/8" Drill bit, Tape measure
Top
(1) 5/16" Hex bolt
section
and lock nut
Carriage bolt
(supplied by others).
and nuts
(supplied by
others)
Center hinge
Typical
door arm
(2) 1/4" - 20 x 2 1/2"
Carriage bolts and (2) 1/4" – 20
Flange hex nuts
Center
hinge
(2) 1/4" - 20 x 2 1/2"
Carriage bolts and (2) 1/4" – 20
Flange hex nuts
Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer,
refer to your local yellow pages business listings or go to the Find a Dealer section online at www.Wayne-Dalton.com
WARNING WARNING
DO NOT INSTALL PuLL DOWN ROPE ON DOORS WITH OPERATORS. CHILDREN
MAy BECOME ENTANGLED IN THE ROPE CAuSING SEvERE OR FATAL INJuRy.
Measure and mark the jamb approximately 48" to 50" (1220 to 1270 mm) from floor on the
right or left side of jamb. Drill 1/8" pilot hole for no. 6 screw eye. Tie the pull down rope to the
no. 6 screw eye and to the bottom corner bracket, as shown.
No. 6 Screw eye
48" to 50"
From floor
Pull
down
rope
17
Typical bottom
corner bracket
Pull down
rope