Page 1
Rearview Mirror with 4.5" Color LCD with Navigation/2 Camera inputs/Compass And Outside Temperature Display Model: LCMR6CT Installation Manual Features: Rearview Mirror with 4.5” LCD Rearview Camera Input Interior View Camera Input Navigation Display Input NTSC /PAL Compatible Camera Input Compass Display...
Do not use any features of this system to the extent it distracts you from safe driving. Your first priority while driving should always be the safe operation of your vehicle. Audiovox Electronics Corporation cannot accept any responsibility whatsoever for accidents resulting from failure to observe these precautions or safety instructions.
TABLE OF CONTENTS Cautions! Preface Packing list 1.Installation Instructions 2.Signal Inputs 3.Controls and Indicators Specifications Maintenance Troubleshooting Illustration of connections...
Please consult the application guide for the appropriate mounting bracket for your vehicle or call Tech Service at 800-225-6074. Packing list The Rear view mirror Model LCMR6CT consists of the following items: 1. Rear View Mirror-1 3. Control Box-1 5. Control Box Monitor Cable -1 7.
Tightly the T-20 mounting bracket screw. (2) Navigation monitor connection (optional): Audiovox navigation monitor cable into the receptacle at the backside of the mirror/monitor. Route the rest of the monitor cable under the headliner, down the A pillar to the Navigation computer.
Page 6
Installing the Temperature Sensor. a) Select a suitable location for the Temperature sensor outside of the vehicle. The location should be in the nose area of the vehicle, between the front of the radiator and front bumper where there will be airflow. Keep the sensor as low as possible, and as far away from the radiator as possible.
Page 7
b ) Secure the Compass sensor using the screw provide or double sided adhesive tape to the selected location with the head of the compass sensor arrowhead facing forward. c ) Route the Compass cable up the A pillar and connect the 5 pin Compass Sensor cable to the mating 5 pin connector of the Temperature/ Compass Y cable.
WARNING: Observe polarity when connecting the wires. To Rearview Camera To Interior Camera To Mirror Assembly To Filter BOX 2. Signal Inputs The signal input connections for the system include: (1) Rear Camera: Plug the RJ 11 camera cable end into the control box AVin-1 location, route the cable to the rear camera and plug the 4-pin connector into camera 4 pin connector.
Page 9
(6) Navigation Image (optional Navigation System required) The Navigation Image is the default mode, and will only be overridden when the vehicle gear selector is moved into reverse, or if the CAM button on the mirror is pressed. Some operators may find that leaving the Navigation Image on the LCD monitor at all times becomes a distraction while operating their motor vehicle.
3. Controls and Indicators Figure 3 shows the function controls of the rear view mirror. A: 4.5" LCD Panel B: Rearview Mirror Glass C: “+”Button (optional Navigation System required) Incrementally increase volume level of the navigation voice command when pressed. Note: Will only operate when the Navigation System remote control is removed from the cradle.
Page 11
E: “MAP” Button (optional Navigation System required) Each time the “MAP” button is pressed, the navigation display will toggle between Map, Icon only and split screen while in navigation mode. Note: Will only operate when the Navigation System remote control is removed from the cradle.
Page 12
Figure 6 Figure 7 N: Calibration Switch: Used to calibrate the compass display.
General Power Supply Power Consumption Current Draw Video Input Audio Input Audio Power Output Operating Temperature Range Display System Screen Brightness Contrast Ratio Backlight Life Resolution Video Format Display Format Navigation input Specifications 12VDC <12W <800mA 1Vp-p/ 75 Impedance <=1V 0.5W ×...
Though your Rearview mirror requires little care, you can still maintain its condition and performance by following the procedures below. Keep your system away from excessive moisture, extreme heat or cold, and magnetic fields. Keep liquids away from the display and mirror. To avoid damage, do not place external devices or other objects on the top of the mirror.
Symptoms The ON/OFF signal light <E> is not on after the car is started? No video signal appears while reversing the car? Video image is not sharp enough? Heading Information is not accurate? Temperature/Compass display does not Change when T/C button is pressed Troubleshooting Solutions Check the installation-wiring diagram.