Chamberlain J Owner's Manual
Hide thumbs
Also See for J:
- Instructions (4 pages) ,
- Installation manual (108 pages) ,
- Owner's manual (40 pages)
Table of Contents
Advertisement
Quick Links
INDUSTRIAL DUTY COMMERCIAL DOOR OPERATOR
2 Y E A R W A R R A N T Y
Serial # Box
Installation Date
O W N E R ' S M A N U A L
J H H J
L
ogic
F A C T O R Y S E T
This Operator Features
the Enhanced
PAT E N T P E N D I N G
The Maintenance Alert System™ allows the
installer to set an internal Maintenance
Cycle Counter. The Logic 3 operator
incorporates a self-diagnostic feature built
into the (MAS) Maintenance Alert System
LED. An LED on the 3-button station will
signal when the set number of cycles is
reached or when the operator requires
immediate service.
Radio Receiver
Built on Board
NOT FOR RESIDENTIAL USE
3
Advertisement
Table of Contents
Troubleshooting
Related Manuals for Chamberlain J
Summary of Contents for Chamberlain J
- Page 1 F A C T O R Y S E T O W N E R ’ S M A N U A L J H H J INDUSTRIAL DUTY COMMERCIAL DOOR OPERATOR This Operator Features the Enhanced PAT E N T P E N D I N G The Maintenance Alert System™...
-
Page 2: Table Of Contents
Standard Power & Control Connection Diagrams ...12 Model J Logic Control 3....... 30 1 Phase Wiring Diagram . -
Page 3: Carton Inventory
19-50106M #50 CHAIN, 106 PITCH 02-103L3 PUSH BUTTON STATION 40-6000 DOOR OPERATOR LABEL 14-12133 PARTS BOX 77-10897 PARTS BAG K77-31334 - MODEL J 10-10893 CHAIN RETAINING BRACKET PART # DESCRIPTION QTY. 14-10466 PLASTIC BAG 19-50106M #50 CHAIN, 106 PITCH 80-207-19 KEY 1/4 X 1-1/2"LONG... -
Page 4: Operator Specifications
DISCONNECT: Secondary: #48 chain/sprocket; Output: #50 chain Model J . . .Floor level disconnect for manual door operation. Model H ... . .Floor level chain hoist with electrical OUTPUT SHAFT SPEED: ......36 RPM interlock for manual door operation. -
Page 5: Preparation
• Disable ALL locks and remove ALL ropes connected to door Both J and H series operators have dual output shafts and may BEFORE installing and operating door operator to avoid be mounted on either the right (standard) or left side of door, and entanglement. -
Page 6: Installation
I N S T A L L A T I O N Before your operator is installed, be sure the door has been properly aligned and is working smoothly. The operator may be wall mounted or mounted on a bracket or shelf. If necessary, refer to the preparation on page 5. Refer to the illustration and instructions below that suits your application. -
Page 7: Manual Operation
This operator includes both a floor level disconnect chain to disconnect the door from the door operator and a disconnect chain with manual hoist to electrically disable the operator controls. 1. Refer to Model H instructions for hoist operation. 2. Refer to Model J instructions for manual operation. -
Page 8: Entrapment Protection Accessories
Connect operator end of coil cord to junction box (not provided) fastened to the wall approximately halfway up the door opening. A D J U S T M E N T WARNING WARNING... -
Page 9: Brake Adjustment
A D J U S T M E N T BRAKE ADJUSTMENT WARNING WARNING A solenoid is standard on 3/4 and 1 horsepower models, and is optional on 1/3 and 1/2 horsepower models. The brake is To avoid SERIOUS PERSONAL INJURY or DEATH from... -
Page 10: Safety Warnings
P O W E R W I R I N G & G R O U N D W I R I N G NING WARNING WARNING To reduce the risk of SEVERE INJURY or DEATH: • ALL electrical connections MUST be made by a qualified individual. -
Page 11: Control Station Wiring & Installation
C O N T R O L S T A T I O N W I R I N G A N D I N S T A L L A T I O N CONTROL WIRING CONNECTIONS EXTERNAL RADIO WIRING CONNECTIONS 1. -
Page 12: Standard Power & Control Connection Diagrams
S T A N D A R D P O W E R & C O N T R O L C O N N E C T I O N D I A G R A M S OPEN Maintenance Alert LED CLOSE... -
Page 13: Phase Wiring Diagram
L O G I C ( V E R . 3 . 0 ) 1 P H A S E W I R I N G D I A G R A M OPEN Maintenance CLOSE Alert LED (RD) (WH) STOP Open 3-Button... -
Page 14: Phase Wiring Diagram
L O G I C ( V E R . 3 . 0 ) 3 P H A S E W I R I N G D I A G R A M OPEN Maintenance Alert LED CLOSE (RD) (WH) STOP Open 3-Button... -
Page 15: Control Board
C O N T R O L B O A R D CONTROL BOARD ILLUSTRATION Ø14LGØ657–A Ø14GPØ657–A C3Ø Auxilliary Board Motor Direction Jumper Connectors D3Ø2 P1Ø Single Phase & Three Phase Jumper Programmed Chip POWER Maintenance Alert TIMER J3ØØ TIMER DEFEAT DEFEAT System button for... -
Page 16: Programming
P R O G R A M M I N G LOGIC CONTROL PUSHBUTTONS OPEN, CLOSE, STOP SELECTOR DIAL Open, Close and Stop buttons are mounted directly on the Logic Control board. Thus, making it easy to program as well as have door control at the electrical box. -
Page 17: Programming
P R O G R A M M I N G FAILSAFE WIRING TYPES SELF-MONITORING SAFETY DEVICE OPTIONS To use the operator in any of the Failsafe wiring modes, or Timer TYPE To Close wiring modes (TS, T, FSTS), a LiftMaster self monitoring FSTS 3-Button Station, 1-Button Station, 1 &... -
Page 18: Programming Remotes
P R O G R A M M I N G PROGRAMMING REMOTES SINGLE BUTTON CONTROL (SBC) REMOTE This function programs a remote as a Wireless Single Button STANDARD SINGLE BUTTON REMOTE Control. In B2 mode, operation is 1. Press and release the RADIO button (LED will light). OPEN/STOP/CLOSE/REVERSE/STOP. -
Page 19: Maintenance Alert System (Mas)
P R O G R A M M I N G MAINTENANCE ALERT SYSTEM (MAS) SELECTOR DIAL Feature: An internal cycle counter will activate a flashing LED on the three button control station when the preset number of cycles or months has elapsed (whichever occurs first). Setting this feature is optional. -
Page 20: Mid Stop
P R O G R A M M I N G OPEN MID STOP Feature: Door will open to an installer set height that is less than fully open. SELECTOR DIAL Benefit: The door opens to a midpoint between open and close reducing heating and cooling costs. -
Page 21: Automatically Learned Programming
P R O G R A M M I N G TIMER TO CLOSE PROGRAM TIMER TO CLOSE BY EXAMPLE (Method 2): SELECTOR DIAL Additional Benefit: Allows the installer to walk through a real life example to set the Timer to Close. To Program: 1. -
Page 22: Maximum Run Timer (Mrt)
A U T O M A T I C A L L Y L E A R N E D P R O G R A M M I N G MAXIMUM RUN TIMER (MRT) Feature: The operator will learn the distance it takes to open or close the door plus approximately 12 - 14". -
Page 23: Resetting Factory Defaults - Clearing Memory
O P T I O N A L P R O G R A M M I N G RESETTING FACTORY DEFAULTS - CLEARING MEMORY SELECTOR DIAL To reset most of the user installed settings back to factory defaults: 1. Turn the selector dial to DIAGNOSTIC 2. -
Page 24: Troubleshooting
T R O U B L E S H O O T I N G DIAGNOSTIC CHART The logic control board has several LED's to assist in the installation and troubleshooting of the operator. The following chart should assist in verifying the operator is functioning properly. Turn the selector dial to DIAGNOSTIC to keep the door from moving while troubleshooting. -
Page 25: Troubleshooting Guide
TROUBLESHOOTING GUIDE FAULT POSSIBLE CAUSE ➤ THE OPERATOR WILL a) Operator control station is wired wrong Use the OPEN, CLOSE and STOP LEDs to help check correct wiring. NOT RESPOND TO ANY Verify that the board is accepting commands by using the onboard COMMANDS station. -
Page 26: Troubleshooting Error Codes
TROUBLESHOOTING ERROR CODES LiftMaster Logic 3.0 operators incorporate a self diagnostic and press the OPEN button. To read out each individual error feature built into the MAS LED. In addition to indicating when code (if more than one exists) press CLOSE. It is possible to have routing maintenance is due, the MAS LED can be used to more than one error at a time. -
Page 27: Illustrated Parts - Electrical Box
I L L U S T R A T E D P A R T S - E L E C T R I C A L B O X... -
Page 28: Repair Parts Kits - Electrical Box Logic Control 3
H5011L3 (Operator) = K-H5011L3 (Electrical box service kit) K10-30637 Rail PCB Mount with Standoffs K75-32269 Cover MOTOR KITS 10-30636 Electrical Box 20-1033B-LP2 Models H, J, HJ 3311L3, 3321L3 21-14182 Transformer, 115/230V 20-3033B-4P Models H, J, HJ 3323L3, 3343L3 21-5460 Transformer, 460V 21-5575 Transformer, 575V... -
Page 29: Illustrated Parts - Model J
I L L U S T R A T E D P A R T S - M O D E L J... -
Page 30: Repair Parts Kits - Model J Logic Control 3
R E P A I R P A R T S K I T S - M O D E L J L O G I C C O N T R O L 3 Refer to the parts lists below for replacement kits available for your operator. If optional modifications and/or accessories are included with your operator, certain components may be added or removed from these lists. -
Page 31: Illustrated Parts - Model H
I L L U S T R A T E D P A R T S - M O D E L H... -
Page 32: Repair Parts Kits - Electrical Box Logic Control 3
86-RP10-112 Roll Pin, 5/16" X 1-3/4" 86-RP10-208 Roll Pin, 5/16" X 2-1/2" K72-19974 OUTPUT SHAFT ASSEMBLY KIT ITEM PART # DESCRIPTION 11-19485 Output Shaft, H/J 15-19478 Sprocket Assembly 15-19480 Dual Sprocket 32/14 15-48B18LGE Sprocket 48B18 X 1" Bore 15-50B12LGH Sprocket 50B12 X 1" Bore 158A0056 Ring, 1"... -
Page 33: Illustrated Parts - Model Hj
I L L U S T R A T E D P A R T S - M O D E L H J... -
Page 34: Repair Parts Kits - Model Hj Logic Control 3
R E P A I R P A R T S K I T S - M O D E L H J L O G I C C O N T R O L 3 Refer to the parts lists below for replacement kits available for your operator. If optional modifications and/or accessories are included with your operator, certain components may be added or removed from these lists. - Page 35 O P E R A T O R N O T E S...
-
Page 36: Control Connection Diagram
EXTERNAL INTERLOCK Note: 11 and 4 are both the same common. Remove Factory Installed Jumper Either is acceptable. When Interlock is Used Sensing Device 2 OR MORE All Wiring Types © 2005, The Chamberlain Group, Inc. 01-19457B All Rights Reserved...