No
Key name
Function
・
Plug AC cord into power outlet while pressing
ON/STANDBY Key and MENU/SET Key same
time on Main Unit.(Be sure to insert the CD
before this operation)
・
Switches to mode according to key input.
See 4.1 and 4.2.
・
If an error occurs, display the error and stop
4
CD heat run mode
operation at that point. Number of operations
held. See 4.3 to 4.5.
・
Heat run no. cleared when STOP key pressed.
・
Mode canceled and tray opened after CD OPEN/
CLOSE key pressed.
・
Unplug AC cord to clear this mode too.
・
After CD heat run mode has started, re-read TOC
and press the CD PLAY/PAUSE key.(Be sure to
finish reading the TOC before push CD PLAY/
PAUSE key) Count this as the 0th heat run
repetition.
①
Play from the first to last track on disc.
②
If disc being used has less than 20 tracks, play
all tracks. If disc has 21 or more tracks, skip to
final track after playback of first track has
finished.
③
After disc playback has finished, move pickup
to innermost position and open tray.
④
When loader open status detected, close tray
Normal heat run
again, re-read TOC and start playback from
4.1
mode
the first track on the disc.
⑤
The heat run repetition no. is incremented
(increased by 1) when the tray is opened.
⑥
Conduct
①
to
⑤
repeatedly.
・
After CD heat run mode has started, re-read TOC
and press the CD STOP/BAND key once in the
stop mode.(Be sure to finish reading the TOC
before push CD STOP/BAND key)
・
TOC reading
⇒
Search for first track on disc
Automatic
4.2
tray open
⇒
tray close
⇒
mounting mode
repeat. No. heat run repetitions displayed on
time display section.
・
Increment the heat run repetition no. (increase
by 1) at the point when the loader has finished
opening.
Display
・
lit
・
Normal display except when
lit.
・
lit
① , ②
・
In cases other than when
is lit, same display as
during normal playback.
③
・
Upper : "_ CD _ _ _ _ _ _ _ _ XXXX_"
・
Lower : "_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _"
・
XXXX : No. of heat run repetitions
④
・
Upper : "_ CD _ _ _ 01Tr _ _ _ _ : _ _"
・
Lower : "_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _"
While tray opened
・
Same as for regular heat run. See 6.1
When tray closed
・
Same as for regular heat run. See 6.1.
⇒
TOC reading
⇒
RCD-M37 / RCD-M37DAB / D-E500 / D-M37
No
キー名称
・ 本体 ON/STANDBY キーと MENU/SET キーを同時に
押しながら、AC コードをコンセントへ接続する.
・キー入力に応じたモードへ移行する.( 必ずディスク
を入れておくこと )
4.1 ∼ 4.2 参照.
・エラーが発生したら、エラー表示をしてその場で動
4
CD ヒートラン モード
作を停止する。動作回数は保持しておく.
4.3 ∼ 4.5 参照.
・STOP キーを押した場合、ヒートラン回数をクリアする.
・CD OPEN/CLOSE キーが押されたら、モードを解除
してトレイをオープンする.
・AC コードを抜くことでもモードを解除する.
・CD ヒートランモードが起動し TOC を読み取り後、
CD PLAY/PAUSE キーを押す.(CD PLAY/PAUSE
キーを押す前に、TOC READ が完了しているこ
と ) この時、ヒートラン繰り返し回数を 0 回目とす
る.
① ディスクの先頭トラックから最終トラックまで再生す
る.
② 使用ディスクが 20 トラック以内の場合は全トラックを
再生する.21 トラック以上なら1トラック目終了後、
最終トラックにスキップする.
③ ディスクの再生終了後、ピックアップを最内周に移
動させトレイを開く.
4.1 通常ヒートランモード
④ ローダー OPEN 状態を検出したら、再度トレイを
閉じ再度 TOC を読み取り後、ディスクの先頭
トラックから再生を開始する.
⑤ ヒートラン回数はトレイを OPEN したところで
インクリメント ( ヒートラン回数を 1 つ増やす ) する.
⑥ ①∼⑤を繰り返し実行する.
・CD ヒートランモードが起動し TOC を読み取り後、 停
止中に CD STOP/BAND キーを 1 回押す.(CD
STOP/BAND キーを押す前に、TOC READ が完了
③
.
していること)
・TOC 読込み⇒ディスクの先頭トラックをサーチ⇒
4.2 チャッキングモード
トレイ OPEN ⇒トレイ CLOSE ⇒ TOC 読込み⇒を繰り
返す。時間表示部にヒートランの繰り返し回数を表
示する。
・ヒートラン回数はローダーを OPEN し終えたところで
インクリメント (increment:ヒートラン回数を 1 つ増やす )
する.
21
機能
表記
・
を点灯
・
を点灯している以外は通常と同じ表示.
・
を点灯
①、②
・
を点灯している以外は通常再生中と同じ表示.
③
・上段:"_ CD _ _ _ _ _ _ _ _ XXXX_"
・下段:"_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _"
・XXXX:ヒートラン繰り返し回数
④
・上段:"_ CD _ _ _ 01Tr _ _ _ _ : _ _"
・下段:"_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _"
トレイオープン中
・通常ヒートラン時と同じ. 6.1 ③を参照
トレイクローズ中
・通常ヒートラン時と同じ. 6.1 ④を参照