Installation Completed; Optional Extras - Jøtul S17-I400 Installation Manual

17. Rotate the smoke bell to the desired position. Tighten the
screws. If a steel chimney is used: The outlet on the smoke
bell must be symmetrical in its rear position.
18. Then install the flue pipe in the product's smoke bell. Use
gasket rope between the smoke bell and the flue pipe.
19. The surround can be made for top outlet or rear outlet.
Installation using a rear outlet: Mark where the hole in the
chimney is to be located and mount the flue insert and flue
pipe according to regulations.
24. Installation using a top outlet: Follow the steps to point
20. Test mount the side panels (part 4/9). Check that the insert
is centrally positioned in relation to the side panels and the
base. There should be approx. 1-2 mm of clearance between
the panels and insert. Fig. 13.
21. Mount the side panels (part 4/9). The panels should be
mounted behind the insert front and adhered to the wall
with acrylic sealant. Fig. 13-2A.
22. Fit the slate tile (part 3/12) into place, see fig. 13-2B. See fig.
13-3 for the installed side panels and slate tile.
23. Lift the cowl into place (part 5/10) and ensure it is properly
aligned (fig. 15-2). For installation of the Jøtul S 17 C, please
follow fig. 16 carefully.
24. The cowl is heavy at the front. Secure the cowl by screwing
the bracket on the top of the cowl to the wall. NB! If using a
top smoke outlet, make sure the securing bracket is not in
the way of the smoke pipe.
pt. 28
25. See when using a steel chimney.
26. Put on the top grate (part 6/11).
27. With top smoke outlet: Cut a hole in the top grate for the
smoke pipe, see fig. 17A and B. The top grate should be
mounted for final installation of the smoke pipe.
28. If a steel chimney is used: If a top-mounted steel chimney is
used, an uninsulated pipe is fitted from the burn chamber
to approximately 10 mm through the top stones.
the gasket is sealed between the smoke pipe and the smoke
outlet. Then fit the steel chimney in accordance with the
operating instructions.
Replace the exhaust deflector (Fig. 6A), and baffle (fig. 6B). Place
the rear burn plate (Fig. 5F) between the ribs of the rear plate.
The side burn plates Fig. 5E) are inserted at an angle at the front
edge and then swivelled into the back edge. An air duct Fig. 5D),
and log retainer (fig. 5C) are positioned last.

5.0 Installation completed

See the General user and maintenance manual for Jøtul I 400 for
use and maintenance of the insert!
5.1 Minor damage
Once the insert has been installed you should fill in any nicks
27.
or irregularities in the concrete. You can use the accompanying
cement filler.
• In order to achieve the best result the surround should
be rubbed down with fine sandpaper, smoothing any
unevenness or sharp edges prior to painting.
• Then apply one coat.
• Mix the powder (cement filler) with water to form a smooth
paste (like toothpaste).
• Smooth away any unevenness, allow to dry and rub down
with fine sandpaper.
• If the hole is deep, we recommend that the filler be applied
in two stages to prevent it sinking.
• Apply a second coat of the desired colour.
5.2 Painting
Painting can take place the day after installation. Use latex paint.
If you prefer a little surface texture, a little tile cement may be
mixed into the paint.
5.3 Cracks
Check that
In some instances, small cracks may appear at the joints after a
few months' use due to settling of the building. These cracks can
be easily repaired:
• Open up the crack with a tool, e.g. a screwdriver, to create
more room for the grouting cement.
• First remove any dust using a vacuum cleaner. Then inject
some acrylic grout, and smooth it off using a wet, soapy
fingertip.
• After a couple of days the joint can be repainted.
6.0

Optional extras

6.1 Floor plate in front of the product
Jøtul S 17 C: Cat no. 300488
Jøtul S 17 W: Cat. no. 30489
6.2 Ash collection system
Cat. no. 341280
6.3 External Air Supply for the Jøtul I 400
Cat. no. 341279
6.4 Outside air connection Ø100
Cat. no. 341296
ENGLISH
21