Toshiba VF-S15 Instruction Manual page 186

 Table of input terminal functions 2
Function
Code
No.
52 IDC PID integral/differential clear
53 IDCN Inversion of PID integral/differential clear
54 DR PID characteristics switching
55 DRN Inversion of PID characteristics switching
56 FORCE Forced run operation
57 FORCEN Inversion of forced run operation
58 FIRE Fire speed operation
59 FIREN Inversion of fire speed operation
60 DWELL Acceleration/deceleration suspend signal
61 DWELLN Inversion of acceleration/deceleration
suspend signal
62 KEB Power failure synchronized signal
63 KEBN Inversion of power failure synchronized signal
64, 65 Factory specific coefficient
70, 71 Factory specific coefficient
74 CKWH Integrating wattmeter(kWh) display clear
75 CKWHN Inversion of integrating wattmeter display clear
76 TRACE Trace back trigger signal
77 TRACEN Inversion of trace back trigger signal
78 HSLL Light-load high-speed operation prohibitive
signal
79 HSLLN Inversion of light-load high-speed operation
prohibitive signal
80 HDRY Holding of RY-RC terminal output
81 HDRYN Inversion of holding of RY-RC terminal output
82 HDOUT Holding of OUT-NO terminal output
83 HDOUTN Inversion of holding of OUT-NO terminal output
88 UP Frequency UP
89 UPN Inversion of frequency UP
90 DWN Frequency DOWN
91 DWNN Inversion of frequency DOWN
92 CLR Clear frequency UP/DOWN
93 CLRN Inversion of clear frequency UP/DOWN
96 FRR Coast stop command
97 FRRN Inversion of coast stop command
98 FR Forward/reverse selection
99 FRN Inversion of forward/reverse selection
*1: Factory specific coefficient parameters are manufacturer setting parameters. Do not change the value of these parameters.
Function
ON: Integral/differential clear, OFF: Clear canceled
Inversion of IDC
ON: Inverted characteristics of  selection
OFF: Characteristics of  selection
Inversion of DR
ON: Forced run operation if specified faults are occurred
( frequency)
OFF: Normal operation
Inversion of FORCE
ON: Fire speed operation ( frequency)
OFF: Normal operation
Inversion of FIRE
ON: Acceleration/deceleration suspend
OFF: Normal operation
Inversion of DWELL
ON: Deceleration stop with synchronizing when power failure
OFF: Normal operation
Inversion of KEB
ON: Integrating wattmeter(kwh) monitor display clear
OFF: Disabled
Inversion of CKWH
ON: Trigger(start) signal of trace function
OFF: Disabled
Inversion of TRACE
ON: Light-load high-speed operation prohibited
OFF: Light-load high-speed operation permitted
Inversion of HSLL
ON: Once turned on, RY-RC are held on.
OFF: The status of RY-RC changes in real time according to
Inversion of HDRY
ON: Once turned on, OUT-NO are held on.
OFF: The status of OUT-NO changes in real time according
Inversion of HDOUT
ON: Frequency increased
OFF: Frequency increase canceled
Inversion of UP
ON: Frequency decreased
OFF: Frequency decrease canceled
Inversion of DWN
OFF
Inversion of CLR
ON: Coast stop (Gate OFF)
OFF: Coast stop canceled
Inversion of FRR
ON: Forward operation command
OFF: Reverse operation command
Inversion of FR
K-31
Action
-
-
conditions.
to conditions.
ON: Clear frequency UP/DOWN
E6581611
Reference
6.24
6.30
6.23
6.19.2
*1
*1
6.36
6.35
6.21
7.2.2
6.10.4
11
3.1.1
6.34.8
7.2.1