Dell 5330dn User Manual page 118

Close Bin1 Door
Close Fuser Door
Tray [x] Open
Tray [x] Open
Close Tray [x]
HCF Open
HCF Open
Close Door
Tray [x] Empty
Load [Size][Type]
HCF Empty
Load [Size][Type]
MPF Empty
Load [Size][Type]
Press Select
Paper Mismatch/
Tray [x]/MPF
Load [Size][Type]
Continue ,
Cancel
Paper Jam 0
Check Toner Cover
MP Tray
Check MPF Door
Paper Jam 0
Check Tray[x]
Paper Jam 1
Open/Close Door
Paper Jam 2...
Duplex jam 0...
Duplex jam 1...
Standard Bin Full/
Standard Bin is 90%
Full
Optional Bin1 Full
Open Heat
Open Heat Error
Power Cycle
Low Heat/
Low heat Error
Power Cycle
Over Heat
Overheat Error
Power Cycle
LSU Motor Error/
LSU Motor Error/
Power Cycle
Hsync Error/
LSU Hsync Error
Power Cycle
Fuser Error
Fuser Fan Locked
Power Cycle
SMPS Error
SMPS Fan Locked
Power Cycle
Fuser Error/
Fuser Not Installed
Check Rear Door
Inner Temp. Error/
Inner Temp. Error
Power Cycle
Deve Motor Error/
Deve Motor Locked
Power Cycle
Power Saver
Warming Up
Downloaded from ManualsPrinter.com Manuals
The rear door of output expander is not
securely latched.
The fuser door is not securely latched.
The displayed tray is open.
HCF(High Capcity Feeder) is open.
There is no paper in the tray.
There is no paper in the HCF.
There is no paper in the multi-purpose
feeder.
The paper size specified in the printer
properties does not match the paper
being loading.
Paper has jammed around the toner
cartridge area.
Paper has jammed in the feeding area of
the multi-purpose feeder.
Paper has jammed in the feeding area of
the paper tray.
Paper has jammed in the paper exit area
or around the toner cartridge area.
Paper has jammed in the paper exit area. Clear the jam. See
Paper has jammed during duplex
printing.
Paper has jammed during duplex
printing.
The output tray is full.
The output tray of output expander is
full.
There is a problem in the fuser unit.
There is a problem in the fuser unit.
There is a problem in the fuser unit.
A problem has occurred in the LSU(Laser
Scanning Unit).
A problem has occurred in the LSU(Laser
Scanning Unit).
There is a problem in the cooling fan of
the printer.
There is a problem in the SMPS fan of the
printer.
The fuser unit is not installed or not
detected.
There is a problem in your printer system. Unplug the power cord and plug it back
There is a problem in the development
motor of the printer.
The printer is in power save mode.
Your printer is warming up now.
Close the door until it locks into place.
Open the rear door and close the fuser
door until it locks into place.
Close the tray until it locks into place.
Close the HCF until it locks into place.
Load paper in the tray. See "Loading
Print Media in the Paper Tray".
Load paper in the HCF. See "Using the
High Capacity Feeder".
Load paper in the multi-purpose feeder.
See "Using the Multi-purpose Feeder".
Load the correct paper in the tray.
Clear the jam. See "Around the toner
cartridge".
Clear the jam. See "Multi-purpose feeder
Jam".
Clear the jam. See "Paper Feed Jam (tray
1)" or "Paper Feed Jam (optional trays)".
Clear the jam. See "In the paper exit
area" or "Around the toner cartridge".
"In the paper exit
area" or "Around the toner cartridge".
Clear the jam. See "Duplex jam 0".
Clear the jam. See "Duplex jam 1".
The output tray can hold up to 250
sheets of plain paper. Once the paper is
removed from the output tray, the printer
resumes printing.
The output expander can hold up to 600
sheets of plain paper. Once the paper is
removed from the output expander, the
printer resumes printing.
Unplug the power cord and plug it back
in. If the problem persists, please call for
service.
Unplug the power cord and plug it back
in. If the problem persists, please call for
service.
Unplug the power cord and plug it back
in. If the problem persists, please call for
service.
Unplug the power cord and plug it back
in. If the problem persists, please call for
service.
Unplug the power cord and plug it back
in. If the problem persists, please call for
service.
Open and then close the rear door.
Unplug the power cord and plug it back
in. If the problem persists, please call for
service.
Install the fuser unit or open and then
close the rear door.
in. If the problem persists, please call for
service.
Unplug the power cord and plug it back
in. If the problem persists, please call for
service.
When data is received, it switches to on-
line automatically.
Please wait a few minutes.