Storing Tv Broadcasts In Your Vcr - Panasonic NV-HV60 Series Operating Instructions Manual

Storing TV Broadcasts in Your VCR

The VCR is fitted with its own tuner (just like a normal TV) and
can be preset to receive up to 99 TV broadcast stations.
Pre-programmed TV Channels
(NV-HV60GL/Australia)
The local TV broadcast channels 2, 7, 9, 10 and 28 are
factory-preset in this VCR.
That is, if you can receive television broadcasts on VHF
channels 2, 7, 9, 10 and UHF channel 28, these are already
tuned on the programme positions with the matching
numbers. However, it is possible to cancel these settings and
tune the local TV broadcast channels to any desired
programme position.
Plug in Auto Tuning
(NV-HV60GN/New Zealand)
When the VCR is turned on after connecting the aerial cable
and the mains lead, Auto Tuning starts.
AUTO TUNING
IN PROGRESS,
PLEASE WAIT.
CH 22 SEARCH 21
END: MENU
During Plug in Auto Tuning
Auto tuning searches for TV stations from VHF minimum to
UHF maximum and memorizes every tuned programme
position.
• If you turn the VCR off during Auto Tuning, Auto Tuning will
stop halfway.
• If the VCR starts playback during Auto Tuning, Auto Tuning
will stop halfway.
To Cancel Auto Tuning Mid-Operation:
Press [MENU] (7) during Auto Tuning. Auto Tuning is
cancelled.
To Restart Plug in Auto Tuning:
1 Press [EJECT] (40) and remove the video cassette.
2 Keep both [Channel] (32) I and J on the VCR
pressed simultaneously for 3 seconds or more during
the VCR on.
• The channel displayed on the VCR display disappears for
a moment then changes to 1.
3 Disconnect the mains lead and then reconnect it.
4 Turn off the VCR and then turn it on.
• Auto Tuning commences.
If Auto Tuning stops halfway by turning the VCR off or a
power failure:
1 Disconnect the mains lead and then reconnect it.
2 Turn off the VCR and then turn it on.
• Auto Tuning commences.
AUTO TUNING IS
COMPLETED.
END: MENU
After Plug in Auto Tuning
Disappears 1
Auto Tuning Using the On Screen Display
Introduction
The VCR is tuned automatically by Plug in Auto Tuning.
However, Auto Tuning using the On Screen Display should be
performed according to the following method if necessary.
Preparations
• Confirm that the TV is on and the VCR viewing channel is
selected.
• Turn on the VCR and select any programme position except
A1 or A2.
• Set [VCR/TV] switch (22) to [VCR].
Operations
1 Press [MENU] (7) to display
the Main menu on the TV
screen.
2 Press [Cursor] (37) (34) to
select [TUNER PRESET] then
press [OK] (23).
3 Press [Cursor] (37) (34) to
select [AUTO TUNE] then press
[Cursor] (37) (21) to start the
Auto Tuning.
• When Auto Tuning is
completed, the On Screen
Display disappears and
programme position 1 is
selected.
Channels that can be Received
VHF
NV-HV60GL 0-12
NV-HV60GN 1-11
Notes:
• Auto Tuning searches for TV stations from VHF minimum to
UHF maximum and memorizes every tuned programme
position. Other programme positions are skipped.
• Auto Tuning takes five or more minutes to complete its
search.
• If the VCR is not correctly tuned by Auto Tuning, follow the
procedure on page 8.
7
MENU
CLOCK SET
TUNER PRESET
SYSTEM
OPTION
SELECT : , OK
END :MENU
MENU
CLOCK SET
TUNER PRESET
SYSTEM
OPTION
SELECT : , OK
END :MENU
TUNER PRESET
CH 1
CLEAR [ OFF ]
AUTO TUNE
SEARCH 3
[ ]
FINE
SELECT: END :MENU
AUTO TUNING
IN PROGRESS,
PLEASE WAIT.
CH 1 SEARCH 100
END: MENU
The number displayed here
is the number of channels
still to be auto tuned.
UHF CATV
28-69 45-470MHz
21-69 45-470MHz