Related Manuals for Panasonic NV-HV62GL
Summary of Contents for Panasonic NV-HV62GL
-
Page 1: Table Of Contents
Operating Instructions Video Cassette Recorder NV-HV62GL/GN Contents Warning and Important Information Controls and Components Connections Tuning the TV to Your VCR Storing TV Broadcasts in Your VCR Setting the Clock of Your VCR Settings Using the On Screen Display Option Setting... -
Page 2: Warning And Important Information
Note: • In any of the above-mentioned conditions, do not operate the VCR for at least 1 hour. This VCR is not equipped with a dew sensor. Press [VCR-ON/OFF] (1) to switch the VCR from ON to standby mode or vice versa. In the standby mode, the VCR is still connected to the mains. -
Page 3: Controls And Components
A: Current time (a: It flashes only when the current time is displayed.) B: Tape counter C: OTR Recording D: Remaining tape time • When you turn off the main unit, VCR display will be dimmed. (38) Infra-red Remote Control Receiver window (39) [REC/OTR]... -
Page 4: Connections
Notes: • If you are using a Panasonic TV, this setting has already been made, and so you do not need to perform the above setting procedure. However, this remote control may not work with some Panasonic TVs. -
Page 5: Tuning The Tv To Your Vcr
• Even if the RF output channel has been changed, it is not necessary to perform Auto Tuning. Storing TV Broadcasts in Your VCR The VCR is fitted with its own tuner (just like a normal TV) and can be preset to receive up to 99 TV broadcast stations. Pre-programmed TV Channels... - Page 6 CLEAR AUTO TUNE numbers: SEARCH FINE 90 for CH-5A, 91 for CH-9A. (Example for NV-HV62GL) • For other channels that require tuning, repeat steps 3, 4, SELECT: END : MENU Press [MENU] (9) twice to exit the On Screen Display.
-
Page 7: Setting The Clock Of Your Vcr
3 years. After 3 years, clock back up in the event of a power failure can only be guaranteed for maximum of 1 hour. Preparations • Confirm that the TV is on and the VCR viewing channel is selected. • Turn on the VCR. Operations 1 Press [MENU] (9) to display the Main menu on the TV screen. -
Page 8: Option Setting
(See to the right.) Clock # Counter # Remaining Tape Time # # NAVI CHECK indicator # Clock • When the VCR is checking the programme data, the message [CHECKING DATA] is displayed. • When the programme data cannot be found, the message [DATA NOT FOUND] appears. -
Page 9: Playback
4 Press [MENU] (9) twice to exit the On Screen Display. Playback Preparations • Confirm that the VCR is on. • Confirm that the TV is on and the VCR viewing channel is selected. • Insert a recorded video cassette. For Normal Playback: Press [PLAY] (8). -
Page 10: Recording
Keep [STOP] (12) pressed for at least 3 seconds. LSQT0869 Recording Preparations • Confirm that the VCR is on. • Confirm that the TV is on and the VCR viewing channel is selected. Operations 1 Insert a video cassette with an intact erasure prevention tab. - Page 11 • The recording pause mode will be automatically cancelled after 5 minutes and return to the stop mode. • The tape recorded in the EP mode on this VCR cannot be played back on the other VCR without EP mode function.
-
Page 12: Recording From An External Source
[STOP] (12) to finish recording. camera Note: • If you leave the VCR in the recording pause mode for more than 5 minutes in step 3 or 6, the VCR automatically switches over to stop mode to protect the video heads. -
Page 13: Timer Recording
Preparations • The VCR must be turned on, or in timer recording standby mode. • Confirm that the TV is on and the VCR viewing channel is selected. • Insert a video cassette with an intact erasure prevention tab. • Check that the clock is set to the correct time. If it has not been set, refer to page 7. -
Page 14: To Check And Cancel A Timer Programme
Preparations • The VCR must be turned on, or in timer recording standby mode. • Confirm that the TV is on and the VCR viewing channel is selected. • Insert a video cassette with an intact erasure prevention tab. 1 Press [I-TIMER] (23) to display the menu for Intelligent Timer on the TV screen. -
Page 15: Search Functions
• The tape length of the inserted cassette must be set correctly. (See page 8.) • The VCR must not be in the timer recording standby mode. • A programme at least 15 minutes must be recorded on the tape. -
Page 16: Time Stamp Function
• When you press [REC] (15) on the remote control during recording. Conditions for correct operation of the Index search function: • The VCR must be in the stop mode or in the playback mode. • Each programme recorded on the tape must be at least 5 minutes long. Preparations •... -
Page 17: Before Requesting Service
• The TV has not been tuned to the VCR. #Tune the TV to the VCR. See page 5. • The video heads are clogged or worn. #Consult Panasonic Customer Care Centre for advice on 132600. (NV-HV62GL only) #Consult your dealer for further advice. -
Page 18: Adjusting The Playback Picture
• If you play back a cassette that was recorded on another VCR, the picture quality may be inferior and it may be necessary to adjust the tracking. Also, on some TVs, the picture may shake in the special playback functions. -
Page 19: Specifications
Colour signal; converted subcarrier phase shift recording VIDEO IN (PHONO); 1.0 Vp-p, VIDEO OUT (PHONO); 1.0 Vp-p, RF Modulate; UHF Channel AU28–69 (NV-HV62GL) NZ21–69 (NV-HV62GN) j6 dBV, AUDIO IN (PHONO); j6 dBV, AUDIO OUT (PHONO); 1 track (Normal-mono only), 2 channels (Hi-Fi sound-stereo) Colour;... - Page 20 LSQT0869 Matsushita Electric Industrial Co., Ltd. F0205Ah0 Web Site: http://www.panasonic.co.jp/global/...