Specifications - Panasonic AJ-D440 Operating Instructions Manual

Specifications

GENERAL
Power supply: AC 120 V, 50 – 60 Hz
Power consumption: AJ-D440; 120 W
AJ-D450; 150 W
Operating ambient temperature: 41 F to 104 F (5 C to 40 C)
Operating ambient humidity: 10% to 90% (no condensation)
Weight: AJ-D440; 33 lbs (15 kg)
AJ-D450; 34.98 lbs (15.9 kg)
Dimensions (W H D): 16-3/4
Recording format: DVCPRO format
Recording tracks: Digital video
Time code;
Digital audio;
Cue Track;
Control (CTL);
Tape speed: 33.820 mm/sec
Recording time: 184 minutes (with AJ-5P92LP)
66 minutes (with AJ-P66MP)
Tape: 1/4-inch thin magnetic layer metal tape
FF/REW time: Less than 3 min (with AJ-5P92LP)
Less than 2 min (with AJ-P66MP)
Editing accuracy*:
Tape timer accuracy:
Servo lock time: Less than 0.5 sec. (color framing/
VIDEO
(Digital video)
Sampling frequencies: Y; 13.5 MHz/P
Quantizing: 8 bits
Error correction: Reed-Solomon product code
(Digital IN/analog component OUT)
Video bandwidth: Y; 30 Hz to 5.5 MHz ( 1.0 dB)
P
S/N ratio: Better than 56 dB
K factor: Less than 2%
(Analog component IN/component OUT)
Video bandwidth: Y; 30 Hz to 5.5 MHz (–1.5 dB to +1.0 dB)
P
S/N ratio: Better than 55 dB
K factor: Less than 2%
(Analog composite IN/composite OUT)
Video bandwidth:
Y; 30 Hz to 4.5 MHz (–1.5 dB to +1.0 dB)
DG: Less than 4%
DP: Less than 3
Y/C delay: Better than 20 ns
K factor: Less than 3%
S/N ratio: Better than 48 dB
(Video input connector)*
Analog component input*: BNC 3 (Y, P
Y; 1.0 Vp-p, 75
P
Analog composite input*: BNC 2, loop-through, 75 on/off
S VIDEO input*: S terminal (4-pin) 1
Y; 1.0 Vp-p, 75
C; 0.286 Vp-p (burst), 75
Reference input: Analog composite
BNC 2, loop-through, 75 on/off
Serial digital component input Complies with SMPTE259M-C standard,
(option)*:
* Items marked with an asterisk ( * ) indicate AJ-D450 only.
6-15/16 16-3/8 inches
(424 175 415 mm)
Recorded in sub-code area
2channels
1 track
1 track
0 frame (using time code)
1 frame (using continuous CTL signal)
standby ON)
, P ; 3.375 MHz
B R
, P ; 30 Hz to 1.0 MHz ( 1.0 dB)
B R
, P ; 30 Hz to 1.0 MHz
B R
(–2.0 dB to +1.0 dB)
, P )
B R
, P ; 0.486/0.7 Vp-p switchable, 75
B R
(75% color bar, 7.5% setup)
BNC 2, active through
(Video output connector)
Analog component output:
Analog composite output:
S VIDEO output:
Serial digital component output
(option):
(Video signals adjustment)
Video output gain:
Video output chroma gain:
Video output hue:
Video output setup:
Video output sync phase:
Video output SC phase:
AUDIO
(Digital audio)
Sampling frequencies:
Quantizing:
Frequency response:
Dynamic range:
Distortion:
Crosstalk:
Wow & flutter:
Headroom:
De-emphasis:
(Cue track)
Frequency response:
(Audio input connector)*
Analog input (CH1/CH2):
Digital input (CH1/CH2) (option):
Serial digital input (option):
(Audio output connector)
Analog output (CH1/CH2):
Digital output (CH1/CH2)
(option):
Serial digital output (option):
Monitor output:
Headphones:
Other input/output connector
Time code input*:
Time code output:
RS-422A input/output:
RS-232C:
Encoder remote:
Weight and dimensions when shown are approximately.
Specifications are subject to change without notice.
– 66 –
BNC 3 (Y, P , P )
B R
Y; 1.0 Vp-p, 75
P , P ; 0.486/0.7 Vp-p switchable, 75
B R
(75% color bar, 7.5% setup)
BNC 3
Video1/video2/video3 (superimpose
on/off)
S terminal (4-pin) 1
Y; 1.0 Vp-p, 75
C; 0.286 Vp-p (burst), 75
Complies with SMPTE259M-C standard,
BNC 3
3 dB
Control from ENCODER
3 dB
30 REMOTE connector
15 IRE
2 s
180
48 kHz
16 bits
20 Hz to 20 kHz ( 1.0 dB)
Better than 85 dB (1 kHz, emphasis OFF,
"A" weighted)
Less than 0.1% (1 kHz, emphasis OFF,
standard level)
Less than –80 dB (1 kHz, between
2 channels)
Below measurable limits
20 dB
T1=50 s/T2=15 s (on/off automatic)
300 Hz to 6 kHz 3 dB
XLR 2, 600 high impedance selectable,
+4/0/–20/–60 dBu
BNC 1, AES/EBU format
Complies with SMPTE259M-C, 272M
standard (BNC)
XLR 2, low impedance, +4/0/–20 dBu
BNC 1, AES/EBU format
Complies with SMPTE259M-C, 272M
standard (BNC)
Phono 1, 600 , –8 dBV
Variable level, 1/4" phone, 8
BNC 1, 0.5 to 8 Vp-p
BNC 1, 2.0 Vp-p
D-sub 9-pin, RS-422A interface
D-sub 25-pin, RS-232C interface
D-sub 15-pin