SQUEEGEE CLEANING/CHECK/REPLACEMENT AND SQUEEGEE BLADE REPLACEMENT (All models)
CAUTION!
It is advisable to wear protective gloves when cleaning the squeegee because there may be sharp debris.
Disassembly and cleaning
1.
Drive the machine on a level floor.
2.
Turn.the.ignition.key.(80).to."0".
3.
Lower.the.squeegee.(25).with.the.lever.(10).
4.
Loosen.the.knobs.(26).and.remove.the.squeegee.(25).
5.
Disconnect.the.vacuum.hose.(15).from.the.squeegee.
6.
Clean.the.steel.squeegee.(Fig..1).or.the.aluminium.squeegee.(Fig..2)..Clean.the.compartments.(A,.Fig..1.or.2).and.the.hole.
(B).especially..Check.the.front.blade.(C).and.the.rear.blade.(D).for.integrity,.cuts.and.tears;.if.necessary.replace.them.(see.the.
procedure.in.the.following.paragraph).
7.
Install.the.squeegee.in.the.reverse.order.of.removal.
Check and replacement
1.
Clean.the.steel.squeegee.(Fig..1).or.the.aluminium.squeegee.(Fig..2),.as.shown.in.the.previous.paragraph.
2.
Check.that.the.edges.(E,.Fig..1.or.2).of.the.front.blade.(C).and.the.edges.(F).of.the.rear.blade.(D).lay.down.on.the.same.level,.
along.their.length;.otherwise.adjust.their.height.according.to.the.following.procedure:
•
Release.the.tie.rod.(G,.Fig..1.or.2).and.loosen.the.wing.nuts.(H,.Fig..1),.or.disengage.the.fasteners.(M,.Fig..2).and.adjust.the.
rear.blade.(D,.Fig..1.or.2),.then.tighten.the.wing.nuts,.or.engage.the.fasteners,.and.then.engage.the.tie.rod.
•
Loosen.the.knobs.(I).and.adjust.the.front.blade.(C,.Fig..1.or.2);.then.tighten.the.knobs.
3.
Check.the.front.blade.(C,.Fig..1.or.2).and.rear.blade.(D).for.integrity,.cuts.and.tears;.if.necessary.replace.them.according.to.the.
following.procedure..Check.that.the.front.corner.(J).of.the.rear.blade.is.not.worn;.otherwise,.overturn.the.blade.to.replace.the.worn.
corner.with.an.integral.one..If.the.other.corners.are.worn.too,.replace.the.blade.according.to.the.following.procedure:
•
Release.the.tie.rod.(G),.remove.the.wing.nuts.(H).or.disengage.the.fasteners.(M),.remove.the.retaining.strip.(K),.then.replace/
overturn.the.rear.blade.(D)..Then.install.the.blade.in.the.reverse.order.of.removal.
•
Unscrew.the.knobs.(I).and.remove.the.retaining.strip.(L),.then.replace.the.front.blade.(C)..Install.the.blade.in.the.reverse.order.
of.removal.
After.the.blade.replacement.(or.overturning),.adjust.the.height.as.shown.in.the.previous.step.
4.
Connect.the.vacuum.hose.(15).to.the.squeegee.
5.
Install.the.squeegee.(25).and.screw.down.the.knobs.(26).
6.
If.necessary,.adjust.the.squeegee.balance.adjusting.knob.(27).
SERVICE MANUAL -
FOCUS
II L17 - S20 - L20 - L20 Cyl. - BOOST
®
RECOVERY WATER SYSTEM
L20
®
ENGLISH
S301552
29