Integra DRX-5 Basic Manual page 43

> Specifications > Settings
■ 3� Distance
Set the distance from each speaker to the listening position.
Setting Item Default Value
Front Left 12.0ft/3.60m
Center 12.0ft/3.60m
Front Right 12.0ft/3.60m
Height Left 9.0ft/2.70m
Height Right 9.0ft/2.70m
Surround Right 7.0ft/2.10m
Surr Back Right 7.0ft/2.10m
Surr Back Left 7.0ft/2.10m
Surround Left 7.0ft/2.10m
Subwoofer 12.0ft/3.60m
• Default values vary depending on the regions.
> Listening Modes > Playback Function
Setting Details
Specify the distance between each speaker and
the listening position.
Specify the distance between each speaker and
the listening position.
Specify the distance between each speaker and
the listening position.
Specify the distance between each speaker and
the listening position.
• The setting cannot be changed if anything
other than "No" is set in "Configuration" - "Zone
Speaker" and Zone 2 is on.
Specify the distance between each speaker and
the listening position.
• The setting cannot be changed if anything
other than "No" is set in "Configuration" - "Zone
Speaker" and Zone 2 is on.
Specify the distance between each speaker and
the listening position.
Specify the distance between each speaker and
the listening position.
• The setting cannot be changed if anything
other than "No" is set in "Configuration" - "Zone
Speaker" and Zone 2 is on.
Specify the distance between each speaker and
the listening position.
• The setting cannot be changed if anything
other than "No" is set in "Configuration" - "Zone
Speaker" and Zone 2 is on.
Specify the distance between each speaker and
the listening position.
Specify the distance between each speaker and
the listening position.
• Distance units can be switched by pressing Mode on the remote controller. When the unit is set as
feet, you can set between 0.1 ft and 30.0 ft in increments of 0.1ft. When the unit is set as meters, you
can set between 0.03 m and 9.00 m in increments of 0.03 m.
■ 4� Level Calibration
Setting Item Default Value
Front Left 0.0 dB
Center 0.0 dB
Front Right 0.0 dB
Height Left 0.0 dB
Height Right 0.0 dB
Surround Right 0.0 dB
> Basic Manual
Troubleshooting Appendix
Setting Details
Select a value between "－12.0 dB" and "＋12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select the
desired level.
Select a value between "－12.0 dB" and "＋12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select the
desired level.
Select a value between "－12.0 dB" and "＋12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select the
desired level.
Select a value between "－12.0 dB" and "＋12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select the
desired level.
• The setting cannot be changed if anything
other than "No" is set in "Configuration" - "Zone
Speaker" and Zone 2 is on.
Select a value between "－12.0 dB" and "＋12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select the
desired level.
• The setting cannot be changed if anything
other than "No" is set in "Configuration" - "Zone
Speaker" and Zone 2 is on.
Select a value between "－12.0 dB" and "＋12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select the
desired level.
|
11