Jøtul GF 3 CF 2 Installation And Operation Instructions Manual page 8

All brick flues or any flue previously used with solid
fuel or gas appliances must be left with the appropri-
ate debris collection volume below the flue spigot of
the stove of 12 litres minimum 12 litres minimum 12 litres minimum 12 litres minimum 12 litres minimum, and depth of 250mm
minimum below the spigot as shown in fig. 9.. Block,
clay, cement or steel lined (connected to the top of the
appliance opening) flues either new or previously used
with GAS appliances may have the smaller debris
collection volume of 2 litres minimum and depth of 2 litres minimum and depth of 2 litres minimum and depth of 2 litres minimum and depth of
2 litres minimum and depth of
75mm minimum below the flue spigot. 75mm minimum 75mm minimum 75mm minimum 75mm minimum
Make sure that there will be at least 50mm
clearance between the end of the spigot and knee of
the fireback for flue gases. Also make sure that the
spigot will pass through the closure plate by a mini-
mum of 15 mm. It can be extended by up to 150 mm (6")
to ensure this requirement is met using a purpose-
made extension or suitable piece of flue pipe. Cut a
closure plate from sheet aluminum or steel to just
cover the appliance opening to be used. It is also
possible to use other fireproof materials providing
they are properly supported and sealed and can be
removed annually for inspection and clearing of the
flue. Cut a spigot hole as shown in the fig. 9. Fix the
closure plate to the wall or appliance and seal it
correctly to the wall. The plate must
rectly to the wall using adhesive sealant, screws and/
or tape able to withstand at least 3 degrees C
appliance will not work correctly and may cut out
repeatedly if the sealing of the appliance and flue is
not correct.
Remember, if the closure plate extends beyond
the sides or top of the stove, a non-combustible
decorative panel can be fitted to cover the area. The
closure plate can then be fitted to this. Marble in-fill
panels are a common example. Install the appliance
and connect to the gas supply and carry out a smoke
test on the flue as described in the relevant section of
this manual.
Minimum Clearances from
Combustible Material to the Vent
System
All pipe components must be installed according to
approval and the instructions of the manufacturer.
Adhere to the instructions of the manufacturer as
regards clearance from to the vent system to combus-
tible material.
When moving the chimney the clearance from
combustible material to the upper side of horizontal
pipe must be minimum 100 mm. The clearance from the
bottom of the vent pipe to combustible material must
be minimum 75 mm.
8
must must be sealed cor- must must
at least 3 degrees C. The at least 3 degrees C at least 3 degrees C at least 3 degrees C
Assembly Prior To Installation
The product is delivered in 1 package. In the firebox
you will find the propane fuel conversion kit, four
decorative pipe brackets, and a log set that includes a
bag of textured embers.
1. Remove the Top Plate of the stove by simply lifting
it straight off of the stove body.
2. To open the firebox, disengage the two Glass Frame
Latches located on top of the firebox. Pull each
handle forward to clear the latch from the notch in
the frame.See fig. 10.
3. Remove the parts wrapped in packaging. Use gloves
to handle the ceramic logs, as they can cause skin
irritation.
4. Familiarize yourself with the installation require-
ments specified in this manual, before beginning
the installation. If the product is going to be used
with Propane G31 rather than G20 natural gas, it
should be converted now. See the instructions
supplied with the conversion kit.
Figure 10. Pull spring latch to disengage from glass frame.
Glass
Frame
Latch