Changing The Unit's Settings; Common Procedures; Tuning - Panasonic DMR-EX71S Operating Instructions Manual

Changing the unit's settings

You can change the unit's settings using Setup menu.
≥The settings remain intact even if you switch the unit to standby.

Common procedures

1
While stopped
Press [FUNCTION MENU].
2
Press [3, 4] to select "To Others"
and press [OK].
3
Press [3, 4] to select "Setup" and
press [OK].
Tabs
Setup

Tuning

Disc
Picture
Sound
Display
Connection
Others
4
Press [3, 4] to select the tab and
press [1].
5
Press [3, 4] to select the menu and
press [OK].
6
Press [3, 4] to select the option and
press [OK].
To return to the previous screen
Press [RETURN].
To exit the screen
Press [EXIT].
Tuning
Edit Profiles
You can create four profiles of channels for making viewing and
recording easier. Editing these profiles does not affect the channel
setting itself.
≥Timer recording may not work correctly if you edit the profiles
during timer recording standby.
Press the "Green" button to select the profile.
Edit Profiles
TV 123... Profile 1
1 Das Erste
2 ZDF
3 RTL Television
4 SAT.1
5 VOX
6 ProSieben
7 RTL2
8 kabel eins
9 Super RTL
Sorting Mode Profile Select Add
SELECT
RETURN
To add channels to a profile
1 Press the "Blue" button to select the channel type.
≥Every time you press the button, you change between:TV TV
encrypted Radio Radio encrypted TV.
≥Encrypted channels are marked with the key symbol in the
corresponding table.
≥The channels can be sorted in numerical or alphabetical order
with "Red" button.
2 Press [3, 4] to select the channel in the left column and press
the "Yellow" button.
≥Repeat the steps 1 – 2 to add other channels.
3 Press [OK] to save the profile.
To change the order of channels of a profile
1 Press [1] .
§
2 Press [3, 4] to select the channel in the right column to move
and press the "Green" button.
3 Press [3, 4] to select the new position of the channel and press
the "Green" button.
≥Repeat the steps 2 – 3 to move other channels.
RQT9193
4 Press [OK] to save the profile.
60
Menus Options
Remote Control DVD 1
Clock
Power Save Off
Quick Start On
DivX Registration
System Update
Initialize
TAB
SELECT
RETURN
OK
TV/Radio
Page +
Page -
To delete channels on a profile
1 Press [1] .
§
2 Press [3, 4] to select the channel in the right column and press
the "Yellow" button.
≥Repeat this step to delete other channels.
≥Press the "Blue" button to delete all the channels from the
profile.
3 Press [OK] to save the profile.
Deleting a channel from a profile does not affect the channel
itself. You can still select the channel from the left column.
To change the name of a profile in the "Profile" column
1 Press [1] .
§
2 Press the "Red" button.
( 39, Entering text)
When the station name of the left column is highlighted
§
Signal Condition
You can check the quality and strength of digital broadcast signals.
Realign the aerial if you are receiving a poor signal.
Press [3, 4] to select "Signal Condition" and press [OK].
The quality and strength of the signal are shown.
Press [W X CH] to select the channel.
Astra 19.2˚E, 10987 MHz, H, 27500 ksym/s, 3/4
Signal Quality 0 10
Signal Strength 0 10
CH +
CH –
RETURN
Signal Quality
Below 2 (display red):
The signal quality is so poor that there may be interference in the
pictures and sound.
2–5 (display orange):
The signal quality is basically adequate, but brief interference in the
pictures and sound is possible in isolated case.
Over 5 (display green):
Optimum picture and sound quality.
Signal Strength
The display for signal strength is grey. "0" means signal strength 0%,
"10" means signal strength 100%.
If the signal is too strong, the display will change from grey to red.
Reduce the signal amplification at your aerial.
≥When the signal is weak:
– adjust the position and direction of the satellite dish.
– check that the current digital broadcast channel is correctly
broadcasting.
Auto-Setup Restart
You can restart auto channel setting if set up (
reason.
When the confirmation screen appears
Press [2, 1] to select "Yes" and press [OK].
You can also use the following method to restart Auto-Setup.
When the unit is on and stopped
Press and hold [X CH] and [CH W] on the main unit until the
country setting screen appears.
All the settings except for the ratings level, ratings password and
clock settings return to the factory preset. The timer recording
programmes are also cancelled.
[Note]
≥Stored tuning data is erased and overwritten by new tuning data
when the "Auto-Setup Restart" is executed.
8) fails for some