Table of Contents
Advertisement
13
3
If you selected 7.2ch/5.2.2ch, 7.2ch SB/FW, or Speaker B in Step 2, select the placement of
the surround speakers.
In a 7.2-channel surround system with surround speakers placed directly at the sides of the listening position,
the surround sound of 5.1-channel sources is heard from the side. This function mixes the sound of the surround
speakers with the surround back speakers so that the surround sound is heard from diagonally to the rear as it
should be.
Depending on the positions of the speakers and the sound source, in some cases it may not be possible to
achieve good results. In this case, set the setting to ON SIDE or IN REAR.
! ON SIDE – Select when the surround speakers is positioned right beside you.
! IN REAR – Select when the surround speaker is positioned obliquely behind you.
4
When 'Setting Change?' is displayed, select Yes.
If No is selected, the setting is not changed.
You will return to the Manual SP Setup menu.
In case of VSX-830
! Default setting: 5.2ch
1
Select 'Speaker System' from the Manual SP Setup menu.
See
Making receiver settings from the System Setup menu
2
Select the speaker system setting.
! 5.2ch – Select when connecting surround speaker and playing a maximum 5.2 ch surround.
! Front Bi-Amp – Select this setting if you're bi-amping your front speakers (see
page 41
).
3
When 'Setting Change?' is displayed, select Yes.
If No is selected, the setting is not changed.
You will return to the Manual SP Setup menu.
Speaker Setting
In case of VSX-930
Use this setting to specify your speaker configuration (size, number of speakers and crossover frequency). It
is a good idea to make sure that the settings made in
Auto MCACC)
on
page 57
are correct. Note that this setting applies to all MCACC presets, and cannot be set
independently.
1
Select 'Speaker Setting' from the Manual SP Setup menu.
2
Choose the set of speakers that you want to set, then select a speaker size.
Use k/l to select the size (and number) of each of the following speakers:
! SW – LFE signals and bass frequencies of channels set to SMALL are output from the subwoofer when YES
is selected. Choose the PLUS setting if you want the subwoofer to output bass sound continuously or you
want deeper bass (the bass frequencies that would normally come out the front and center speakers are also
routed to the subwoofer). If you did not connect a subwoofer choose NO (the bass frequencies are output
from other speakers).
— If you have a subwoofer and like lots of bass, it may seem logical to select LARGE for your front speakers
and PLUS for the subwoofer. This may not, however, yield the best bass results. Depending on the speaker
placement of your room you may actually experience a decrease in the amount of bass due low frequency
cancellations. In this case, try changing the position or direction of speakers. If you can't get good results,
listen to the bass response with it set to PLUS and YES or the front speakers set to LARGE and SMALL
alternatively and let your ears judge which sounds best. If you're having problems, the easiest option is to
route all the bass sounds to the subwoofer by selecting SMALL for the front speakers.
on
page 106
if you're not already at this screen.
Bi-amping your speakers
Automatically conducting optimum sound tuning (Full
! Front – Select LARGE if your front speakers reproduce bass frequencies effectively, or if you didn't connect a
subwoofer. Select SMALL to send the bass frequencies to the subwoofer.
! Center – Select LARGE if your center speaker reproduces bass frequencies effectively, or select SMALL to
send bass frequencies to the other speakers or subwoofer. If you didn't connect a center speaker, choose NO
(the center channel is sent to the front speakers).
! TMd – Select LARGE if your top middle speakers reproduce bass frequencies effectively, or select SMALL to
send bass frequencies to the other speakers or subwoofer. When setting up the Dolby Enabled Speaker on
the front speaker, please select Dolby Sp (Front). When setting up the Dolby Enabled Speaker on the sur-
round speaker, please select Dolby Sp (Surr). If you didn't connect the top middle speakers, choose NO (the
top middle channel is sent to the front speakers).
— You can adjust this setting only when Speaker System setting is 7.2ch/5.2.2ch.
— If you change the setting from Dolby Sp (Surr) or Dolby Sp (Front) to SMALL or LARGE, the set value
for Speaker Distance may be changed. This is because the maximum value of Speaker Distance when
set to Dolby Sp (Surr) or Dolby Sp (Front) is bigger than the maximum value of Speaker Distance when
set to SMALL or LARGE. If the value of Speaker Distance set to Dolby Sp (Surr) or Dolby Sp (Front)
exceeds the maximum value of Speaker Distance for SMALL or LARGE, Speaker Distance for SMALL or
LARGE is set to its maximum value.
! FW – Select LARGE if your front wide speakers reproduce bass frequencies effectively, or select SMALL to
send bass frequencies to the other speakers or subwoofer. If you didn't connect front wide speakers, choose
NO (the front wide channel is sent to the front speakers).
— You can adjust this setting only when Speaker System setting is 7.2ch SB/FW.
— If the surround speakers are set to NO, this setting will automatically be set to NO.
on
! Surr – Select LARGE if your surround speakers reproduce bass frequencies effectively. Select SMALL to send
bass frequencies to the other speakers or subwoofer. If you didn't connect surround speakers choose NO (the
sound of the surround channels is sent to the front speakers or a subwoofer).
! SB – Select the number of surround back speakers you have (one, two or none). Select LARGEx2 or LARGEx1 if your
surround back speakers reproduce bass frequencies effectively. Select SMALLx2 or SMALLx1 to send bass frequen-
cies to the other speakers or subwoofer. If you didn't connect surround back speakers choose NO.
— You can adjust this setting only when Speaker System setting is 7.2ch/5.2.2ch, 7.2ch SB/FW or
Speaker B.
— If the surround speakers are set to NO, the surround back speakers will automatically be set to NO.
If you select NO for the subwoofer, the front speakers will automatically be fixed to LARGE. Also, the center, top
middle, surround, surround back and front wide speakers can't be set to LARGE if the front speakers are set to
SMALL. In this case, all bass frequencies are sent to the subwoofer.
3
Select 'X. OVER' and set the crossover frequency.
Frequencies below this point will be sent to the subwoofer (or LARGE speakers).
! This setting decides the cutoff between bass sounds playing back from the speakers selected as LARGE, or
the subwoofer, and bass sounds playing back from those selected as SMALL. It also decides where the cutoff
will be for bass sounds in the LFE channel.
! With Full Auto MCACC setup or Auto MCACC setup (ALL or Speaker Setting), the setting here will not
apply and the crossover frequency will be automatically set. Crossover frequency is a frequency aimed at
achieving the optimal sound field taking into account the bass capacity of all connected speakers and human
aural characteristics.
4
When you're finished, press RETURN.
You will return to the Manual SP Setup menu.
107
The System Setup and Other Setup menus
Advertisement
Table of Contents
