Table of Contents
Advertisement
03
! When connecting to an HDMI/DVI-compatible monitor using the HDMI OUT 2 terminal, switch the HDMI
output setting to OUT 2 or OUT 1+2. See
Switching the HDMI output
Also, MAIN/HDZONE must be set to MAIN beforehand
! For input components, connections other than HDMI connections are also possible (see
player with no HDMI output
on
page 28
).
! If you want to listen to the sound of the TV over the receiver, connect the receiver and TV with audio cables.
— When the TV and receiver are connected by HDMI connections, if the TV supports the HDMI ARC (Audio
Return Channel) function, the sound of the TV can be input to the receiver via the HDMI OUT terminal, so
there is no need to connect an audio cable. In this case, set ARC at HDMI Setup to ON (see
page 82
).
After setting the ARC, some time may be required for the connected device to be recognized and the sound to
be produced.
— If you use a coaxial digital audio cable or RCA (analog) audio cable, you'll need to tell the receiver which digi-
tal or analog audio input you connected the TV to (see
— Please refer to the TV's operation manual for directions on connections and setup for the TV.
! If the TV to be connected using HDMI supports 4K/60p, you can switch the 4K/60p signal input setting in
accordance with TV performance. When the 4K/60p setting is changed to 4:4:4, the video image may not be
output normally unless the HDMI cable supports 4K/60p 4:4:4 24 bit (18 Gbps transmission). In such a case,
select 4:2:0
(page 88
).
! You cannot input 4K/60p 4:4:4 24 bit video from HDMI IN 3 to the IN 6 terminal. Use the BD IN, HDMI IN 1 or
HDMI IN 2 terminal.
! The HDMI OUT 2 terminal outputs 4K/60p 4:4:4 24 bit video when MAIN/HDZONE is set to MAIN. When it is
set to HDZONE, the 4K/60p 4:4:4 24 bit video is not output.
on
page 88
.
(page 111
).
Connecting your DVD
HDMI Setup
The Input Setup menu
on
page 59
).
Connecting your equipment (In case of VSX-930)
Connecting your DVD player with no HDMI output
This diagram shows connections of a TV (with HDMI input) and DVD player (or other playback component with no
HDMI output) to the receiver.
HDMI/DVI-compatible monitor
on
VIDEO OUT
HDMI IN
HDMI OUT
2
1
HDZONE/MAIN
MAIN
ARC CONTROL
SELECTABLE
VIDEO IN
COMPONENT VIDEO
ASSIGNABLE
L
(SAT/CBL)
VIDEO
1
DVD
P
R
R
DVD
P
B
SAT/
L
CBL
Y
R
ASSIGNABLE
SAT/CBL
ANALOG
(CD)
1
AUDIO IN
! If you want to listen to the sound of the TV over the receiver, connect the receiver and TV with audio cables
(page 27
).
— When the TV and receiver are connected by HDMI connections, if the TV supports the HDMI ARC (Audio
Return Channel) function, the sound of the TV can be input to the receiver via the HDMI OUT 1 terminal, so
there is no need to connect an audio cable. In this case, set ARC at HDMI Setup to ON (see
page 82
).
! When connecting to a DVD player with an optical digital audio cable or a coaxial digital audio cable, perform-
ing input terminal settings are necessary
! If HDZONE is set to on, video images connected using a video cable or component cable are not output from
the HDMI terminal. To output video images, turn HDZONE off
28
DVD player, etc.
Select one
Select one
COMPONENT VIDEO OUT
AUDIO OUT
VIDEO
PR
R
ANALOG
L
Y
PB
HDMI IN
1 6 -
ASSIGNABLE
1
BD
2
3
4
6
/MHL
(OUTPUT 5 V
( DVD )
( SAT/CBL )
0.9 A MAX)
HDMI OUT
1
HDMI IN
ASSIGNABLE
1 6 -
2
1
1
BD
2
3
4
6
/MHL
HDZONE/MAIN
MAIN
(OUTPUT 5 V
(DVD)
(SAT/CBL)
0.9 A MAX)
SELECTABLE
ARC CONTROL
VIDEO IN
COMPONENT VIDEO
ASSIGNABLE
L
(SAT/CBL)
VIDEO
1
P
DVD
R
DVD
R
P
B
SAT/
L
CBL
Y
R
ASSIGNABLE
SAT/CBL
ANALOG
1
(CD)
AUDIO IN
(page 59
).
(page 89
).
DIGITAL OUT
OPTICAL
COAXIAL
DIGITAL IN
OPTICAL
( TV )
1
ASSIGNABLE
COAXIAL
( SAT/CBL )
1
ASSIGNABLE
DIGITAL IN
OPTICAL
1
(TV)
ASSIGNABLE
COAXIAL
1
(SAT/CBL)
ASSIGNABLE
HDMI Setup
on
Advertisement
Table of Contents
