Checking The Connections Of Leads; Audio Adjustments; Displaying The "Audio" Setting Screen; Using Fader/Balance Adjustment - Pioneer AVH-X8890BT Owner's Manual

System settings
3 Set the external storage device to this product.
 Refer to Inserting and ejecting an SD memory card on page
8
 Refer to Plugging and unplugging a USB storage device on
page 9
4 Turn the source off.
 Refer to Selecting a source on page 11
5 Display the "System" setting screen.
 Refer to Displaying the "System" setting screen on page
37
6 Touch [System Information].
7 Touch [Firmware Update].
8 Touch [Continue] to display the data transfer
mode.
Follow the on-screen instructions to finish updating the
firmware.
p If an error message appears on the screen, touch the display
and perform the above steps again.
Checking the connections of
leads
Check that the leads are properly connected between this
product and vehicle.
1 Display the "System" setting screen.
 Refer to Displaying the "System" setting screen on page
37
2 Touch [System Information].
3 Touch [Connection Status].

Illumination
Displays the status of headlights or small lamps of the
vehicle.

Audio adjustments

Displaying the "Audio" setting
screen
1 Press the button.
2 Touch , and then .

Using fader/balance adjustment

1 Display the "Audio" setting screen.
 Refer to Displaying the "Audio" setting screen on page 41
2 Touch [Fader/Balance].
p Only the balance can be adjusted when "On" is selected in
"Rear Speaker". Touch [Balance] and skip to step 4.
 Refer to Setting the rear speaker output on page 41.
3 Touch or to adjust the front/rear speaker
balance.
p Set "Front" and "Rear" to "0" when using a dual speaker
system.
4 Touch or to adjust the left/right speaker
balance.
 You can also set the value by dragging the point
on the displayed table.
Switching sound muting/
attenuation
You can automatically mute or attenuate the AV source volume
and the iPhone or smartphone application volume when the
navigation outputs the guidance voice.
The default setting is "ATT".
1 Display the "Audio" setting screen.
 Refer to Displaying the "Audio" setting screen on page 41
2 Touch [Mute Level].
3 Touch the item.
 ATT:
The volume becomes 20 dB lower than the current volume.

Mute:
The volume becomes 0.
 Off:
The volume does not change.

Adjusting source levels

SLA (source level adjustment) lets you adjust the volume level of
each source to prevent radical changes in volume when switch-
ing between sources.
p Settings are based on the FM tuner volume level, which
remains unchanged.
p This function is not available when the FM tuner is selected
as the AV source.
1 Compare the FM tuner volume level with the
level of the source.
2 Display the "Audio" setting screen.
 Refer to Displaying the "Audio" setting screen on page 41
3 Touch [Source Level Adjuster].
4 Touch or to adjust the source volume.
p If you directly touch the area where the cursor can be moved,
the SLA setting will be changed to the value of the touched
point.
p "+4" to "–4" is displayed as the source volume is increased
or decreased.
p The default setting is "0".

Setting the rear speaker output

A rear speaker output of this product can be turned on or off.
The default setting is "On".
1 Display the "Audio" setting screen.
 Refer to Displaying the "Audio" setting screen on page 41
2 Touch [Rear Speaker] to switch "On" or "Off".
p If "Off" is selected, the rear speaker adjustment is not availa-
ble in "Speaker Level", "Time Alignment" and "Crossover".

Setting the subwoofer output

This product is equipped with a subwoofer output mechanism,
which can be turned on or off.
The default setting is "On".
1 Display the "Audio" setting screen.
 Refer to Displaying the "Audio" setting screen on page 41
2 Touch [Subwoofer] to switch "On" or "Off".
p If "Off" is selected, the rear speaker adjustment is not availa-
ble in "Speaker Level", "Time Alignment" and "Crossover".
41