Pioneer AVH-P4000DVD Installation Manual

AVH-P4000DVD
Printed in Thailand
Напечатано в Таиланде
<CRD4280-A/N> RE <KSNNX> <07K00000>
Connecting the units
WARNING Note
• To avoid the risk of accident and the potential • This unit cannot be installed in a vehicle without
violation of applicable laws, the front DVD or TV ACC (accessory) position on the ignition switch.
(sold separately) feature should never be used
while the vehicle is being driven. Also, Rear
Displays should not be in a location where it is a
visible distraction to the driver.
• In some countries or states the viewing of images
on a display inside a vehicle even by persons
other than the driver may be illegal. Where such
regulations apply, they must be obeyed and this
unit's DVD features should not be used.
ACC position No ACC position
CAUTION
• Use this unit in other than the following
• PIONEER does not recommend that you conditions could result in fire or malfunction.
install or service your display yourself. — Vehicles with a 12-volt battery and negative
Installing or servicing the product may grounding.
expose you to risk of electric shock or other — Speakers with 50 W (output value) and 4 ohm
hazards. Refer all installation and servicing
to 8 ohm (impedance value).
of your display to authorized Pioneer service • To prevent short-circuit, overheating or
personnel. malfunction, be sure to follow the directions
• Secure all wiring with cable clamps or below.
electrical tape. Do not allow any bare wiring — Disconnect the negative terminal of the
to remain exposed.
battery before installation.
• Do not drill a hole into the engine — Secure the wiring with cable clamps or
compartment to connect the yellow lead adhesive tape. To protect the wiring, wrap
of the unit to the vehicle battery. Engine adhesive tape around them where they lie
vibration may eventually cause the insulation against metal parts.
to fail at the point where the wire passes from — Place all cables away from moving parts, such
the passenger compartment into the engine
as gear shift and seat rails.
compartment. Take extra care in securing the — Place all cables away from hot places, such as
wire at this point. near the heater outlet.
• It is extremely dangerous to allow the display — Do not pass the yellow cable through a hole
lead to become wound around the steering into the engine compartment to connect to a
column or gearshift. Be sure to install the
battery.
display in such a way that it will not obstruct — Cover any disconnected cable connectors with
driving. insulating tape.
• Make sure that wires will not interfere with — Do not shorten any cables.
moving parts of the vehicle, such as the — Never cut the insulation of the power cable of
gearshift, parking brake or seat sliding
this unit in order to share the power to other
mechanism. equipment. Current capacity of the cable is
• Do not shorten any leads. If you do, the limited.
protection circuit may fail to work properly. — Use a fuse of the rating prescribed.
— Never wire the speaker negative cable directly
to ground.
WARNING
— Never band together multiple speaker's
negative cables.
LIGHT GREEN LEAD AT POWER CONNECTOR
IS DESIGNED TO DETECT PARKED STATUS
AND MUST BE CONNECTED TO THE POWER
SUPPLY SIDE OF THE PARKING BRAKE SWITCH.
IMPROPER CONNECTION OR USE OF THIS
LEAD MAY VIOLATE APPLICABLE LAW AND MAY
RESULT IN SERIOUS INJURY OR DAMAGE.
Connecting the units
• Control signal is output through blue/white cable
when this unit is powered on. Connect it to an
external power amp's system remote control or
the vehicle's auto-antenna relay control terminal
(max. 300 mA, 12 V DC). If the vehicle is equipped
with a glass antenna, connect it to the antenna
booster power supply terminal.
• Never connect blue/white cable to external power
amp's power terminal. Also, never connect
it to the power terminal of the auto antenna.
Otherwise, battery drain or malfunction may
result.
• IP-BUS connectors are color-coded. Be sure to
connect connectors of the same color.
• Black cable is ground. This cable and other
product's ground cable (especially, high-current
products such as power amp) must be wired
separately. Otherwise, fire or malfunction may
result if they are accidentally detached.
Connecting the units
Parts supplied
Parts marked (*) are pre-installed.
This product Power cord USB cable
Holder* Side bracket (2 pcs.)* Trim ring
Frame Flush surface screw Binding screw
(5 × 6 mm) (8 pcs.) (5 × 6 mm) (8 pcs.)
(4 pcs. are pre-installed.)
Binding screw* Rubber bush Double-ended screw
(3 × 6 mm) (8 pcs.)
Touch panel pen